Adze PETROGRAD, half round N1
The semicircular adze was created in accordance with the recommendations of the Union of Carpenters, for which we sincerely thank Vladimir Popov and Evgeny Malenkov.
Forged tempered to hardness - 58-60HRc. Made of spring steel 65G (Germany 66Mn4, Ck67, USA 1066).
Blade width - 60 mm. Total length - 450 mm. Weight 1.2 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Adze PETROGRAD, half round N2
Adze N2 created on the basis of a study of ancient tools, made in the northern regions of Russia and now stored in our Museum of Ancient Instruments.
Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 70 mm. Total length - 500 mm. Weight - 1.3 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Adze PETROGRAD, half round N3
Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia
Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Adze PETROGRAD, straight N1, 460mm/75mm
Straight adze.
Forged tempered to hardness of 58-60HRc. The blade are made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The blade width is 74 mm. Total length - 450 mm. Weight - 1.1 kg.
The adze handle is made of maple wood and covered with tung oil and has a curved finish and is fixed on a wooden wedge.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Adze PETROGRAD, straight N5, 490mm/85mm
Straight adze.
Forged tempered to hardness of 58-60HRc. The blade are made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The blade width is 85 mm. Total length - 500 mm. Weight - 1.22 kg.
The adze handle is made of maple wood and covered with tung oil and has a curved finish and is fixed on a wooden wedge.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Adze PETROGRAD, straight N6, 490mm/35mm
Adze PETROGRAD, straight N6, 490mm/35mm. The forged hardened blade has a hardness of 58-60 HRc. The shank is made of 65G spring steel. The handle is made of maple wood and is coated with oil. The flap is securely fastened to two wedges. Hatchet PETROGRAD, N9. All testers are equipped with leather covers that protect the cutting edge from damage during transportation and storage of the tool. Designed for picking narrow grooves, recesses and for work in hard-to-reach places.
Weight 1.1kg. The ax is 480mm long.
Production - factory of joinery and carpentry tools PETROGRAD
Made in Russia
Carving adze PETROGRAD, model N1
Wood carving adze PETROGRAD.
This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of Tesla.
Developed and designed carving adze - V. Sasin.
The ergonomic handle allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.
Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool - it is 9 profile.
The eye has a wedge shape. The adze handle slides and splits into 3 wedges.
Sharpening the cutting edge - chamfer outside. It is preferable to use this adze at the finishing stages, for stripping, for smooth formation of the transition from the vertical wall to the flat bottom.
Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Carving adze PETROGRAD, model N2, 270mm/45mm
Carving adze PETROGRAD.
This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.
Developed and designed carving adze - V. Sasin.
The ergonomic handle of maple allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.
Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool - it is 9 profile.
The eye has a wedge shape. The adze handle slides and splits into 3 wedges.
Sharpening the cutting edge - double-sided. This model is considered universal, since the geometry of sharpening is a cross between number 1 and number 3. But not without flaws. It is more deeply able to pierce the wood and sometimes gets stuck.
Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Carving adze PETROGRAD, model N4, 270mm/45mm
Carving adze PETROGRAD.
This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.
Developed and designed carving adze - V. Sasin.
The ergonomic handle of maple allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.
Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 45mm. Cutting edge bending radius - 100mm. If to speak it is applicable to the carving tool - it is 2 profile.
The eye has a wedge shape. The adze handle slides and splits into 3 wedges.
Sharpening the cutting edge - external. It is more deeply able to pierce the wood and sometimes gets stuck.
Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Carving adze PETROGRAD, model N5, 270mm/45mm
Carving adze PETROGRAD.
This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.
Developed and designed carving adze - V. Sasin.
The ergonomic handle of maple allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.
Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool - it is 9 profile.
The eye has a wedge shape. The adze handle slides and splits into 3 wedges.
Sharpening the cutting edge - double-sided. This model is considered universal, since the geometry of sharpening is a cross between number 1 and number 3. But not without flaws. It is more deeply able to pierce the wood and sometimes gets stuck.
Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Adzes
Popular goods
Textile 6 pocket Tool Roll, PETROGRAD, for carving knives
This tool roll is designed to store short chisels and knives in an amount of up to 6 pieces. The bag is made of black cotton fabric. The maximum tool length is 180 mm. The length of the tool roll in expanded form -360mm. Compartment for chisels has a strap - to close the cutting part of the knives. Lacing is provided for fixing the twist bag. Made in Russia.
Marking knife PETROGRAD, model N2, arrow form
Marking knives PETROGRAD have a unilateral right or left sharpening and bevel at an angle of 30 and 45 degrees. The blade of the knife is made of high carbon steel and hardened to 59HRC, it passes through the entire handle - this allows you to use it not only as a marking knife, but also as a power knife jamb. Blade thickness - 1.7mm, width - 19mm. The lining is made of beech wood, covered with tung oil and fastened with brass rivets. The length of the knife is 165mm, the blade is 70mm.
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 60 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 60 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete JT, 90°
Checkering tool has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Cutter JT is designed for the passage of long lines and correction of existing ones. Due to the length does not go with a given path for which he received the name jointer. The handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The teeth provide good removal of all hard wood. The cutter is just the same as cutting: deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth.
The width of the working part is 4 mm, the length of the working part is 32 mm, the apex angle is 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete L- 9, 60°
Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-20, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 90°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Bit for checkering tool C-1, 60°
Насадка на резец для чекеринга C-1, 60° (одна РК) имеет 1 пирамидальный зуб. Уголы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резецы С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
