Checkering tool complete T-24, 60°

Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.

At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

500p(7.69)
Отзывов: 1
Рейтинг :

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete B-2

Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete B-3

Checkering tool B-3 is a single blade with teeth. Profile cutter convex semicircular designed to perform the edging pattern. The tool leaves a concave semicircular groove. Good for beginners, as forgiving some mistakes in the work. All cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. maximum groove depth 2.8 mm, width 2.8 mm.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete BBT 11/16`

Rubber mounted, chatter-free cutters, shave out excess wood without "digging in". Leaves barrel channel smooth and ready for barrel, without gouging, rasping or final sanding.

2440p(37.53)
Отзывов: 1
Рейтинг :

Checkering tool complete BBT 3/4`

Rubber mounted, chatter-free cutters, shave out excess wood without "digging in". Leaves barrel channel smooth and ready for barrel, without gouging, rasping or final sanding.

3020p(46.45)
Отзывов: 1
Рейтинг :

Checkering tool complete C-1, 60°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 60 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 60 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L- 9, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L- 9, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-10, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-10, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-11, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-11, 90°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-12, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete L-12, 60°

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete N2-16, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete N2-16, 90°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter №2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tool complete N2-18, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p(13.07)
Отзывов: 1
Рейтинг :

Checkering tools

In this category you will find tools for marking and applying checkering.

Checkering is a type of decoration or even a type of wood carving in the form of parallel notches, diamonds and lines. It is very popular to apply this decoration to rifle stocks and handless, knife handles, vases and other items where a secure grip is required.

The minimum tool set required for applying checkering includes cutters of the same size or pitch. First groove cutter - one-edge cutter, parallel-groove cutter with left-hand or right-hand cutting edge (RC), and a graver for cleaning and trimming where other cutters are missing. You may also need tools for easy checker layout, especially those parallel to curved shapes.

Videos

youtube video
youtube video

Strop PETROGRAD, for carving tools, 150mm*30mm

The bar with glued leather is designed for finishing semi-circular chisels, drawknives, etc. One of the flat sides can also be used for fine-tuning of flat tools. The size of the bar is 150x30 mm. Min radius - 3 mm, max. radius -6 mm. It can be used with polishing pastes. Material - ash, leather - reversal 2mm. Leather color may differ from the image on the site. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv)

Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv). A complete analogue of the Norwegian drawknife Meddragskniv. The thickness of the blade is 6 mm, the radius of the groove is 35 mm, the distance between the handles is 400 mm, the angle of grinding is 30 degrees. Forged, hardened 65G steel (Germany 66Mn4, Ck67, USA 1066) blade, cutting edge hardness - 55-58HRC. Total weight ~ 1.1kg. Handle length - 140mm. Handles are made of beech.
Designed for finishing the lunar groove after adze (removes the effect of scaly). The shape of the shoulder allows you to rotate it when working to grind the entire surface of the groove. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.

12300p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 38mm

Forged carpentry chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

8700p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 50mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

The blade is forged manually from steel ШХ15 (USA analog is 52100, G52986, J19965; Germany  analog of 1.3505, 100Cr6, 102Cr6) and hardened to 58-61 HRC. Carpentry chisels are intended for timber framing for processing deep grooves in logs and timber as an indispensable tool for the construction of frame structures in the style of timber frame, post-and-beam half-timbered, fachwerkhaus, Log house.

  • Chisel blade fastened to the handle with a conical socket.
  • The thickness of the blade at the neck is 11 mm, the thickness in the area of the descent is 7 mm.
  • The handles are made of ash and crimped with a stainless ring to harden the butt when working with a mallet or hammer.
  • Available in widths of 19 mm, 25 mm, 38 mm, 40 mm and 50 mm ( see full catalogue).
  • Blade length 200-250 mm, full length 320 mm.
  • The wedge-shaped blade prevents jamming in the wood.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

9200p
Отзывов: 1
Рейтинг:

Carving set PETROGRAD, N9

Set of 3 wood carving tools. Best choice for starting wood carving spoons. This set is all what you will need to star wood carving your first spoon. All blades a razor sharp and ready to cut out of the box.

The set N9 includes:
  • Carving knife PETROGRAD, Bogorodsky type, 155mm/40mm
  • Carving knife PETROGRAD, skew 40 deg, 165mm/35mm
  • Spoon knife ( hook knife ) model N1, D 27mm, right one
  • Wooden case for 3 wood carving knives
Wood carving knives was produced by Petrograd toolwork in Saint Petersburg Russia
7900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl VII, handle n11

Hand forged outdoor axe Roslavl VII with curved handle.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

10500p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 20mm

Стамеска ПЕТРОГРАДЪ, серия Волга, 20 мм. Производятся шириной от 3мм до 50мм. Кованые стамески Волга спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков.
Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при доработке шиповых соединений и соединений на ласточкин хвост. Толщина лезвия переменная и увеличивается от РК к рукояти.
Полотно из инструментальной высоколегированной стали, закалено до 61HRc. Спинка столярной стамески или рабочая сторона выровнена на плоскошлифовальных станках. Стамески Волга производства фабрики Петроградъ заточены и готовы к работе. Заводской угол заточки 25град.
Деревянная рукоять выполнена из твердых пород древесины, усилена латунным кольцом для силовой работы с киянкой.
3100p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 32mm

Стамеска ПЕТРОГРАДЪ, серия Волга, 32мм. Производятся шириной от 3мм до 50мм. Кованые стамески Волга спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков.
Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при доработке шиповых соединений и соединений на ласточкин хвост. Толщина лезвия переменная и увеличивается от РК к рукояти.
Полотно из инструментальной высоколегированной стали, закалено до 61HRc. Спинка столярной стамески или рабочая сторона выровнена на плоскошлифовальных станках. Стамески Волга производства фабрики Петроградъ заточены и готовы к работе. Заводской угол заточки 25град.
Деревянная рукоять выполнена из твердых пород древесины, усилена латунным кольцом для силовой работы с киянкой.
3400p
Отзывов: 1
Рейтинг:
new

Spoon knife, PETROGRAD, type 1/22, left-handed

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3000p
Отзывов: 1
Рейтинг:
new

Книга "Резьба деревянной ложки своими руками", Игорь Васильева

Книга "Резьба деревянной ложки своими руками", Игорь Васильева посвящена процессу создания деревянной ложки. Начиная от подготовительных работ и заканчивая финишным покрытием.

850p
Отзывов: 1
Рейтинг: