new

Cup Chuck D35mm for Woodturning Lathe M20х1.5mm, PETROGRAD

Chuck diameter 35mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М20х1.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :
new

Adaptor Petrograd, Spindel D10mm x M33*3.5mm

Adapter for lathe chucks, М33 * 3.5mm / holder D10mm. It is used for mounting a chuck with M33x3.5 connecting thread in the tailstock quill. The shank with a diameter of 10mm can be clamped into both a drill chuck and a collet. Material - steel 20.
Convenient for gluing segment rings, and coaxial gluing of halves of projects.

Production of the PETROGRAD factory.
Made in Russia.

1500p(23.07)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D35mm for Woodturning Lathe 1` - 8 UNC

Chuck diameter 35mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it.. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D35mm for Woodturning Lathe M33х3.5mm

Chuck diameter 35mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М33х3.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06) out of stock
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D45mm for Woodturning Lathe M33х3.5mm

Патрон-чашка, Петроградъ, D45мм, М33х3.5мм. Диаметр патрона 45мм. Стальной незакаленный патрон для точения в центрах. Резьба М33х3.5мм. 

Изготовлен на фабрике столярных и плотницких инструментов ПЕТРОГРАДЪ.
Производство (Россия)

2800p(43.06) out of stock
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D25mm for Woodturning Lathe 1` - 8 UNC

PETROGRAD Cup Chuck D25mm for Woodturning Lathe 1` - 8 UNC. Chuck diameter 25mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread 1 '- 8 UNC (8tpi). Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D25mm for Woodturning Lathe M33х3.5mm

PETROGRAD Cup Chuck D25mm for Woodturning Lathe M33х3.5mm. Chuck diameter 25mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М33х3.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D45mm for Woodturning Lathe 1` - 8 UNC

Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread 1 '- 8 UNC (8tpi). Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D55mm for Woodturning Lathe M33х3.5mm

Chuck diameter 55mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М33х3.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

PETROGRAD Cup Chuck D55mm for Woodturning Lathe 1` - 8 UNC

Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread 1 '- 8 UNC (8tpi). Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.

Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)

2800p(43.06)
Отзывов: 1
Рейтинг :

Chucks

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1200p
Отзывов: 1
Рейтинг:

Mallet PETROGRAD, round, D65mm*250mm, 300 g

Wooden mallet, round shape. Solid wood mallets made by woodturning. Mallet weight 300 gramm. Mallets made of beech wood and covered with tung oil. Round mallets used for working with mortise chisels and woodcarving chisels. It used when cutting joints and when carving large elements or sculptures (work from under the mallet).
700p
Отзывов: 1
Рейтинг:

Adze PETROGRAD, half round N3

Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia

Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

9700p
Отзывов: 1
Рейтинг:

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

600p
Отзывов: 1
Рейтинг:

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 60 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 60 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 25mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 38mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6500p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 50mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

The blade has forged manually from steel ШХ15 (USA analog is 52100, G52986, J19965; Germany  analog of 1.3505, 100Cr6, 102Cr6) and hardened to 58-61 HRC. Carpentry chisels are intended for timber framing for processing deep grooves in logs and timber as an indispensable tool for the construction of frame structures in the style of timber frame, post-and-beam half-timbered, fachwerkhaus, Log house.

  • Chisel blade fastened to the handle with a conical socket.
  • The thickness of the blade at the neck is 11 mm, the thickness in the area of the descent is 7 mm.
  • The handles are made of ash and crimped with a stainless ring to harden the butt when working with a mallet or hammer.
  • Available in widths of 19 mm, 25 mm, 38 mm, 40 mm and 50 mm ( see full catalogue).
  • Blade length 300 mm, full length 410 mm.
  • The wedge-shaped blade prevents jamming in the wood.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7000p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 38mm

Forged carpentry chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7600p
Отзывов: 1
Рейтинг: