Plane blade, PETROGRAD, 50mm*175mm

The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 50 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2900p(44.6)
Отзывов: 1
Рейтинг :

Plane blade, PETROGRAD, 60mm*175mm

The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 60 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

3100p(47.68)
Отзывов: 1
Рейтинг :

Stanley standart plane blade, PETROGRAD, 51mm * 3.2mm

Replacement blades for Stanley, Dictum and similar planers are designed to replace a worn blade or expand the capabilities of your tool. They allow replacing native knives on Stanley / Dictum planers, 4, semi-jointing planes 5.
The piece of iron is made of steel 9XC. Hardened to 59-61 HRC. Knife length - 175 mm, width 50mm, minimum thickness 3.5mm.
Knives have two sides - one hard, one soft (production feature)
Each knife is tested with a hardness tester.
The hard side has 2 points from the diamond cone - test, and control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without impairing the working qualities of the tool.
Knives for wooden planers are made at the factory of joinery and carpentry tools PETROGRAD
Production - Russia

3200p(49.22)
Отзывов: 1
Рейтинг :

Stanley standart plane blade, PETROGRAD, 51mm * 2.5mm

Replacement blades for Stanley, Record and similar planers are designed to replace a worn blade or expand the capabilities of your tool. They allow replacing native knives on Stanley / Record planers, 4, semi-jointing planes 5.
The piece of iron is made of steel 9XC. Hardened to 59-61 HRC. Knife length - 175 mm, width 50 mm, minimum thickness 2.5 mm.
Each knife is tested with a hardness tester.
The hard side has 2 points from the diamond cone - test, and control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without impairing the working qualities of the tool.
Knives for wooden planers are made at the factory of joinery and carpentry tools PETROGRAD
Production - Russia

3200p(49.22) out of stock
Отзывов: 1
Рейтинг :

Scrub plane blade, PETROGRAD, 30mm*175mm

The scrub plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 30 mm, thickness minimum 2.2 mm, thickness maximum 3.5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

3200p(49.22)
Отзывов: 1
Рейтинг :

Blank blade for moulding plane, `strip`, w/o sharpening, 10mm*180mm

The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

item item code shank width mm minimum shank thickness  mm flag length mm flag width mm flag max thickness   mm overall length mm
Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm М00014997  10  3,2  - 10 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm М00015123  10  3,2 40   16 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm М00014666 10 3,2 40 20 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm М00014590 10 3,2 40 24 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm М00014667 10 3,2 40 30 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm М00015124 10  3,2   40 36   4,6 180
800p(12.3) out of stock
Отзывов: 1
Рейтинг :
%

Blank blade for moulding plane, `flag`, w/o sharpening, 24mm*180mm

The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

item item code shank width mm minimum shank thickness  mm flag length mm flag width mm flag max thickness   mm overall length mm
Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm М00014997  10  3,2  - 10 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm М00015123  10  3,2 40   16 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm М00014666 10 3,2 40 20 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm М00014590 10 3,2 40 24 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm М00014667 10 3,2 40 30 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm М00015124 10  3,2   40 36   4,6 180
900p(13.84) out of stock
Отзывов: 1
Рейтинг :

Blank blade for moulding plane, `flag`, w/o sharpening, 36mm*180mm

The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

item item code shank width mm minimum shank thickness  mm flag length mm flag width mm flag max thickness   mm overall length mm
Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm М00014997  10  3,2  - 10 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm М00015123  10  3,2 40   16 4,6  180
Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm М00014666 10 3,2 40 20 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm М00014590 10 3,2 40 24 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm М00014667 10 3,2 40 30 4,6 180
Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm М00015124 10  3,2   40 36   4,6 180
900p(13.84) out of stock
Отзывов: 1
Рейтинг :

Plane blade, PETROGRAD, 30mm*110mm

The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 80 mm, width 30 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2700p(41.53)
Отзывов: 1
Рейтинг :

Plane blade, PETROGRAD, 40mm*175mm

The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 175 mm, width 40 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2800p(43.06)
Отзывов: 1
Рейтинг :

Plane blade, PETROGRAD, 65mm*175mm

The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 175 mm, width 65 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

3200p(49.22)
Отзывов: 1
Рейтинг :
new

Stanley standart plane blade, PETROGRAD, 60mm * 3.2mm

Нож для рубанка, стандарт Stanley/Dictum, 60мм, толщина 3.2мм предназначен для  Stanley, Dictum и похожей конструкции. Используются для замены изношенного ножа или расширения возможностей вашего инструмента. Позволяют заменить родные ножи на выглаживающих рубанках Dictum номер 4 1/2. Производство фабрика Петроградъ (Россия).

3200p(49.22) out of stock
Отзывов: 1
Рейтинг :

Toothing plane blade, PETROGRAD, 40mm*175mm

 Предназначен для подготовки заготовок под склейку, наклеивания шпона и т.п. Также может использоваться для обработки свилеватой и твердой древесины.
Ширина ножа 40мм. Масса 0,150 кг.

Толщина железка - от 5.5мм (у РК) до 3.5мм (у хвостовика)
Ранее изготовлялись железки толщиной 3.5мм/2.2мм, часть рубанков может быть укомплектована именно такими ножами.
Это не брак, тонкие ножи работают также хорошо, как и толстые

 

Все железки ПЕТРОГРАДЪ имеют клиновидный спуск с углом 0,5 градуса. Это выгодно отличает их от других рубаночных ножей, и делает их идеально подходящими для деревянных рубанков с клиновой фиксацией ножа. Рабочая сторона ножа, закалённая до твёрдости 59-61 HRc, помечена небольшими точками, остающимися от проверки ножа твёрдомером. Эти точки, имеющиеся на каждом ноже, являются свидетельством проверки ножей и не влияют на работоспособность изделия.

ВАЖНО! Обратная сторона ножа, не помеченная контрольными точками, не является рабочей!

Производитель оставляет за собой право изменять толщину ножа без ухудшения рабочих качеств инструмента.

4500p(69.21)
Отзывов: 1
Рейтинг :

Scrub plane blade, PETROGRAD, 50mm*175mm

Knife for a semi-jointer, PETROGRAD, sherhebel pit, 50mm * 175mm. Also suitable for the PETROGRAD # 4 planer. The piece of iron is made of steel 9XC. Hardened to 59-61 HRC. Has dimensions: total length 175 mm, width 50 mm, minimum thickness 2.2 mm, maximum thickness 3.5 mm. Sharpening angle 30 °. All glands are wedge-shaped with a wedge angle of 0.5 °.
What sets it apart from others is ideal for wedge-fixed wooden planers. The knife has two sides - one hard, one soft (production feature).
Each knife is tested with a hardness tester. The hard side has 2 points from the diamond cone - test, and control test.

Production - Russia

3400p(52.29)
Отзывов: 1
Рейтинг :

Blades for hand planes

All hand plane blades by Petrograd toolworks(Russia) maded localy, have a wedge-shaped descent with an angle of 0.5 degrees. This sets them apart from other blades and makes them ideal for wedge-retained wooden planers.

The working side of the blade, hardened to a hardness of 59-61HRc, is marked with small holes remaining from checking with a hardness tester. These notches, which are present on each blade, are evidence that the blade had been checked and do not affect the performance of the product.

The assortment of hand plane blades by Petrograd toolworks is constantly replenishing and today it has 18 of it, ranging from blades for classic smoothing planers to exotic types blades for router planes, rabbet planes and moulding type planes and etc.

By purchasing a hand plane blade by Petrograd toolworks, you are buying a high-quality and reliable thing that will serve and delight you for years.

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-18, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-18, 90°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N3-18, 90°

Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N4-18, 90°

Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete S-1, 90°

Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.

It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.

Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.

The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, right-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The right version of knife is designed to work with the right hand towards yourself or left hand to outside.

  • Knife blade width - 12mm.
  • Spoon cutter length - 235 mm
  • Handle length - 160 mm
  • Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

3600p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 1, single stright bevel

Straight and flat leather Knife type 1 with a single bevel (up or right). This model has one flat side and one bevel side. It's simple knife for paring and skiving.

  • for straight cuts
  • for skiving
  • for paring

Flat Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and ready to work out of the box.
This type of knives is used in handicraft, leather work, and shoemaking.

  • blade made of tool alloy steel 9ХФ
  • blade thickness - 1.7 mm
  • edge lenght - 40 mm
  • blade lenght - 70mm
  • handle made of wood *
  • oil covered **
2600p
Отзывов: 1
Рейтинг:

Bit for checkering tool S-1, 90°

Насадка на резец для чекеринга S-1, 90° (одна РК) имеет 1 пирамидальный зуб. Углы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резцы S-предназначен для обработки углов и изгибов, а также труднодоступных мест. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

570p
Отзывов: 1
Рейтинг:

Axe Anika, model Tomohawk

Топор Аника, Томагавк, с чехлом. Ультра-легкий топор Томагавк с обухом-молотком. Идеальный инструмент для передвижений налегке и хозяйственной деятельности в лесу. Заточка с микроподводом для работ по сухой и сырой древесине. Вес головы — около 600 грамм. Вес топора — около 800 грамм. Общая длина — 400-450 мм.
7900p
Отзывов: 1
Рейтинг: