%

Marking knife PETROGRAD, model N4, right bevel

Marking knife PETROGRAD, model N4, right bevel. A knife for the right hand and an awl on the handle produced by PETROGRAD. It can also be used to work in the marquetry technique. Knife bevel angle 30 degrees. RK sharpening angle 30 degrees. Cutting edge width 28mm. Knife thickness 5.5mm. The total length of the knife is 180mm. The blade is made of high carbon steel and hardened to 58-61HRC.
Manufacture of carpentry and carpentry tools factory Petrograd

3200p(49.22)
Отзывов: 1
Рейтинг :

Marking knife PETROGRAD, model N2, arrow form

Marking knives PETROGRAD have a unilateral right or left sharpening and bevel at an angle of 30 and 45 degrees. The blade of the knife is made of high carbon steel and hardened to 59HRC, it passes through the entire handle - this allows you to use it not only as a marking knife, but also as a power knife jamb. Blade thickness - 1.7mm, width - 19mm. The lining is made of beech wood, covered with tung oil and fastened with brass rivets. The length of the knife is 165mm, the blade is 70mm.

2500p(38.45) out of stock
Отзывов: 1
Рейтинг :
%

Marking knife PETROGRAD, model N4, double bevel

Marking knife PETROGRAD, model N4, double bevel. Knife with double-sided sharpening and an awl on the handle produced by PETROGRAD. It can also be used to work in the marquetry technique. Knife bevel angle 30 degrees. RK sharpening angle 30 degrees. Cutting edge width 28mm. Knife thickness 5.5mm. The total length of the knife is 180mm. The blade is made of high carbon steel and hardened to 58-61HRC.
Manufacture of carpentry and carpentry tools factory Petrograd

3200p(49.22) out of stock
Отзывов: 1
Рейтинг :
%

Marking knife PETROGRAD, model N4, left bevel

Marking knife PETROGRAD, model N4, left bevel. A knife for the left hand and an awl on the handle produced by PETROGRAD. It can also be used to work in the marquetry technique. Knife bevel angle 30 degrees. RK sharpening angle 30 degrees. Cutting edge width 28mm. Knife thickness 5.5mm. The total length of the knife is 180mm. The blade is made of high carbon steel and hardened to 58-61HRC.
Manufacture of carpentry and carpentry tools factory Petrograd

3200p(49.22) out of stock
Отзывов: 1
Рейтинг :

Marking knife PETROGRAD, model N5, arrow form

Marking knives  PETROGRAD have a swept blade that is sharpened on 2 faces, which makes it comfortable to use both right-handed and left-handed. One-sided sharpening. The 2.3mm thick blade is made of high carbon steel and hardened to 58-61HRC. The handle is made of curly maple and saturated with linseed oil. Before the blade on the handle made a comfortable stop to prevent sliding of the hand. The length of the handle is 170mm.Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia

1500p(23.07) out of stock
Отзывов: 1
Рейтинг :

Marking knife PETROGRAD, model N5, skew form

Marking knife N5, right bevel. This knife is a carpentry tool for precision marking, it has one-sided sharpening. Blade of marking tool is made of high carbon steel and hardened. Best for marking woodwork joints, may be used for cutting veneer.

Knife blade was sharpened and ready to work out of the box.

  • high carbon steel
  • hardened to 59-61 HRc
  • blade length - 23mm
  • blade thickness - 2.3mm
  • sharpening angle - 30 degrees
  • skew angle - 40 degrees
1500p(23.07) out of stock
Отзывов: 1
Рейтинг :

Marking knife PETROGRAD, model N3, flexible, arrow form

Dovetail Marking knife N3 has flexible blade with arrow form. This knife is a carpentry tool for precision marking, it has one-sided sharpening. Blade of marking tool is made of high carbon steel and hardened. Best for marking dovetail joints. Arrow form give easy two side marking: forward and backwark.

Knife blade was sharpened and ready to work out of the box.

  • high carbon steel ( like 60SG2A steel (Germany 66Mn4, Ck67, USA 1066))
  • hardened to 59-61 HRc
  • blade length - 40 mm
  • blade width - 9 mm
  • blade thickness - 0.73 mm
  • sharpening angle - 30 degrees
  • skew angle - 60 degrees
1300p(19.99) out of stock
Отзывов: 1
Рейтинг :
%

Marking knife PETROGRAD, model N6, whale form

Нож разметочный ПЕТРОГРАДЪ, модель N6, кит. Нож для правой или левой руки, с двусторонней заточкой производства ПЕТРОГРАДЪ. Этот нож прорезает на дереве глубокую тонкую линию и подрезает волокна. Предназначен для высокоточной разметки и направления захода стамески, долота или пилы.

3200p(49.22) out of stock
Отзывов: 1
Рейтинг :

Marking knife PETROGRAD, model N3, flexible, skew form

The alloy steel flexible blade knife is the ideal tool for marking dovetail joints. In addition to marking operations, they can be used for various types of work: for cutting veneer as a knife for marquetry, for cutting clay and plasticine, paper.

A knife with a beveled blade.
The bevel angle is 45 °.
Sharpening angle of the blade with an angle of 30 °.
Blade thickness - 0.7mm,
Width - 9mm.
Blade length - 40 mm,
Knife length - 200 mm.
The handle is made of hardwood, covered with oil.

Manufactured by the Petrograd factory (Russia).
1300p(19.99) out of stock
Отзывов: 1
Рейтинг :

Marking knives

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N2-18, 60°

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N3-18, 60°

Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Checkering tool complete N4-18, 60°

Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 1, single stright bevel

Straight and flat leather Knife type 1 with a single bevel (up or right). This model has one flat side and one bevel side. It's simple knife for paring and skiving.

  • for straight cuts
  • for skiving
  • for paring

Flat Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and ready to work out of the box.
This type of knives is used in handicraft, leather work, and shoemaking.

  • blade made of tool alloy steel 9ХФ
  • blade thickness - 1.7 mm
  • edge lenght - 40 mm
  • blade lenght - 70mm
  • handle made of wood *
  • oil covered **
2600p
Отзывов: 1
Рейтинг:

Straight Gouge Rubankov, N3, 6mm

Straight Gouge Rubankov, N3, 6mm


Straight Gouge Rubankov, N3, 6mm (0.43 inches)
Carving chisel "Rubankov" Straight Gouge N3, 6mm (0.43 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 6mm ( 0.43 inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

4000p
Отзывов: 1
Рейтинг:

Straight Gouge Rubankov, N2, 14mm, fishtail

A professional level cutting tool designed for processing hardwoods and hardwoods. The basis of any set of carving tools is straight chisels. Straight chisels "fish tail" (FT) are suitable for solving problems from creating curly shapes to the selection of lamps, allow you to work in hard-to-reach places where a regular straight chisel cannot handle. They can be used beveled up or down to create concave or convex surfaces.
RUBANKOV chisels are forged from low-alloy high-carbon steel. Hardened to a hardness of 59-61 HRc.
The faceted handle is made of precious wood and covered with oil. The impact side is rounded so as not to crush calluses on the palms. The brass ring has an exquisite look and the effect of the handle from cracking when working with a mallet. The internal profile of the chisel is polished, the detected edge is sharpened and ready for work.
These models are percussion, they can be paired with a mallet.
The declared geometric dimensions vary in handling, as the tool is made and hoarded by hand.
The length of the metal sheet is 145 mm. Overall length with handle 280mm.
Web width - 14mm.

Made at the PETROGRAD joinery and carpentry tools factory.
Production Russia.
4200p
Отзывов: 1
Рейтинг:

Straight Carving Chisel Rubankov, N1, 10mm

Straight carving gouge N1 has 10mm wide blade(0.39 inches) and slight profile for better carving abilities. It is universal wood carving chisel that perfectly suits for carving hard or soft wood. Best choice for relief wood carving.

  • cutting edge width - 10mm (0.39 inches)
  • blade lenght is 145mm (5.71inches)
  • Made of alloy steel
  • hand forged
  • hardened to 59-61HRc
Gouge is sharpened, honed and fully ready to work out of the box.

Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

4000p
Отзывов: 1
Рейтинг:
new

Carving set PETROGRAD n19, 6 tools, chisel handles

Набор мини стамесок для резьбы по дереву, ПЕТРОГРАДЪ, N19, 6 предметов. Авторский набор мини-стамесок для миниатюрной резьбы по дереву. Эти прекрасные инструменты подойдут для моделистов, любителей миниатюрной резьбы и для максимальной деталировки резьбы. Набор включает три плоские прямые стамески, две косые стамески и одну полукруглую стамеску. Производство Россия.

9500p
Отзывов: 1
Рейтинг:

Petrograd Bushcraft Straight Gouge, n7, 30mm

Прямая стамеска для вырезания ложки, профиль Н7, ширина 30 мм. Эта стамеска была специально разработана с оглядкой на нужды ложкарей, ее профиль и общие габариты, даже внешний вид, подобраны исходя из эргономики изготовления деревянной ложки. Прямые стамески подходит для множества задач от создания фигурных форм до подбора фона Стамеска подойдет и для классической резьбы при съеме материала. Производство фабрика Петроградъ (Россия)

3800p
Отзывов: 1
Рейтинг: