new

Screwdriver PETROGRAD, for brass screws, 8mm*1.0mm*125mm

Screwdriver PETROGRAD, for working with planers, 8mm * 1.0mm * 125mm (weapon). The total length of the screwdriver is 125 mm, the blade width is 8 mm, the blade thickness is 1.0 mm. The screwdriver is specially designed for thin splines. The material of the blade is hardened tool steel to a hardness of 56 -58 HRc, the handle is made of fine wood, covered with oil and assembled on brass rivets.

PETROGRAD screwdrivers are presented in four models. Screwdrivers can be used both as weapons and for various other tasks.

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

1200p(16.66)

Screwdriver PETROGRAD, 8mm*1.2mm*210mm, for plane frog

PETROGRAD screwdrivers are represented by three models. Screwdrivers can be used to adjust the hand tools (planers, saws), and as a gun care screwdriver. The material of the blade is 9XC (DIN - 150Cr14) steel hardened to 56-58 HRc, the handle is made of maple and assembled on brass rivets.

The first model of PETROGRAD screwdriver has a straight tip for installing handles. The total length is 125 mm, the tip size is 10 mm * 1.4 mm. The screwdriver is specifically designed for tightening the screws of the handles and the clamping screw on the planes (except No1), also suitable for other tasks. Exactly fits the size of the slot of the plane screws, which gives the necessary strength without sliding and stalling the slot on the soft brass screws. 

The second model of a PETROGRAD screwdriver has a straight tip for mounting a chip breaker. Total length 125 mm, tip size 12 mm * 1.6 mm. The screwdriver is specially designed for tightening the chipbreaker screw on planes, also suitable for other tasks. Exactly fits the size of the slot of the plane screws, which gives the necessary strength without sliding and stalling the slot on the soft brass screws. 

The third model of a PETROGRAD screwdriver has a straight tip for installing a frog. Total length 210 mm, tip size 8 mm * 1.2 mm. The screwdriver is specially designed for tightening the frog's screws on planes, and is also suitable for other tasks. Exactly fits the size of the slot of the planer screws, which gives the necessary strength without sliding and stalling the slot on the soft brass screws. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1200p(16.66)

Screwdriver PETROGRAD, for plane handles, 10mm*1.4mm*125mm

PETROGRAD screwdrivers are represented by three models. Screwdrivers can be used to adjust the hand tools (planers, saws), and as a gun care screwdriver. The material of the blade is 9XC (DIN - 150Cr14) steel hardened to 56-58 HRc, the handle is made of maple and assembled on brass rivets.

The first model of PETROGRAD screwdriver has a straight tip for installing handles. Total screwdriver length 125 mm, tip width 10 mm, tip thickness 1.4 mm. The screwdriver is specifically designed for tightening the screws of the handles and the clamping screw on the planes (except No1), also suitable for other tasks. Exactly fits the size of the slot of the plane screws, which gives the necessary strength without sliding and stalling the slot on the soft brass screws. 

 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1200p(16.66)

Screwdriver PETROGRAD, for chipbreaker, 12mm*1.6mm*125mm

PETROGRAD screwdrivers are represented by three models. Screwdrivers can be used to adjust the hand tools (planers, saws), and as a gun care screwdriver. The material of the blade is 9XC (DIN - 150Cr14) steel hardened to 56-58 HRc, the handle is made of maple and assembled on brass rivets.

The second model of a PETROGRAD screwdriver has a straight tip for mounting a chip breaker. Total screwdriver length 125 mm, tip width 12 mm, tip thickness 1.6 mm. The screwdriver is specially designed for tightening the chipbreaker screw on planes, also suitable for other tasks. Exactly fits the size of the slot of the plane screws, which gives the necessary strength without sliding and stalling the slot on the soft brass screws. 

 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1200p(16.66)

Screwdrivers

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

3 800p

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

1 350p

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

 

1 670p

Flat U-shaped drawknife is designed for joinery, woodcarving, as well as for carpentry. Ideal for making Windsor chairs. Handles are in the same plane with the blade that allows easy control of the tool, and their direction at an angle to the cutting edge allows for less stress on the wrists.. The 3.5 mm thick blade has a straight cutting edge, made of carbon steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 57-59 HRC. Handles 100mm long made of maple, impregnated with oil and reinforced with a brass ring. Blade length - 135 mm, width 20 mm. Sharpening angle - 30grad. Includes leather case to protect the blade. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

 

3 000p

Honing guide PETROGRAD is designed to hold the tool at a given angle when manually grinding on abrasive stones. Min clamping length - 60mm, max. width - 82mm, max. thickness - 7mm. Equipped with self-centering clamp for precise blade positioning. It is used for sharpening chisels, plane blades, etc. The limited applicability for Japanese compound blades. It has a roller that does not damage the stone and makes it easy to grind. Made in Japan

2 080p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

340p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

370p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

450p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

520p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

750p