Checkering set, type N2, 90°/18lines, 8 tools + gauge, in roll bag

Set N2 (90 degrees, 18 lines) includes 8 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 90 degree cutters, this type is making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 2 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 90° ( two cutting edges )
  • gouge N3-18, 90° ( right router, left cutting edges )
  • gouge N4-18, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • gouge for corners 90° (or Carving chisel, PETROGRAD, V-type, 90 degrees)
  • gouge for marking rifle handles
  • checkering gauge
  • roll bag for carving tools model N1 ( 12 pockets )

Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools: 8 tools
Type of checkers: 90 degrees
Number of lines: 18 lines on 1 inch
Handle material: Beech*
Handle lenght: 120 mm
Total lenght: 240 mm
Total weight: 0.4 kg

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

9000p(0)
Отзывов: 1
Рейтинг :

Checkering set, type N1, 60°/18lines, 6 tools

Checkering Set N1 (60 degrees, 18 lines) includes 6 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 60 degree cutters, this type is making more open semi-flat checkers that grants good grip and less prone to clogging than flat ones.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 60° ( two cutting edges )
  • gouge N3-18, 60° ( right router, left cutting edges )
  • gouge N4-18, 60° ( left router, right cutting edges )
  • gouge C-1, 60° ( one cutting edge )
  • Checkering gauge
  • roll bag for carving tools ( 6 pockets )

Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools: 6 tools
Type of checkers: 60 degrees
Number of lines: 18 lines on 1 inch
Handle material: Beech*
Handle lenght: 120 mm
Total lenght: 240 mm
Total weight: 0.3 kg

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.

6300p(0)
Отзывов: 1
Рейтинг :

Checkering set, type N3, 90°/18lines, 10 tools + gauge, in roll bag

Full tool set for checkering N3 (90 degrees, 18 lines) includes 10 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. This is most full set of tools for making checkers a on rifle handles. Gouges with 90 degree cutters in this set are making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 3 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 90° ( two cutting edges )
  • gouge N3-18, 90° ( right router, left cutting edges )
  • gouge N4-18, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • gouge L- 9, 90° ( right router with wide space, left cutting edge )
  • gouge R- 9, 90° ( left router with wide space, right cutting edge )
  • gouge for corners 90° (or Carving chisel, PETROGRAD, V-type, 90 degrees)
  • gouge for marking rifle handles
  • checkering guage
  • roll bag for carving tools model N1 ( 12 pockets )
Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools: 10 tools
Type of checkers: 90 degrees
Number of lines: 18 lines on 1 inch
Handle material: Beech*
Handle lenght: 120 mm
Total lenght: 240 mm
Total weight: 0.55 kg

  1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
    It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
    Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
    The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
    The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °
  2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
  3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm
  4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
  5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle
  6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees
10800p(0)
Отзывов: 1
Рейтинг :
new

Checkering set, type N2, 60°/20lines, 8 tools + gauge, in roll bag

Checkering tool set N2, 8 tools + layout and roll bag for storage. Gouges by Petrograd toolsworks for making checkers. Set of tools with 60 degree cutters, this type is making more open semi-flat checkers that grants good grip and less prone to clogging than flat ones.

Checkering tool set 2 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge C-1, 60° ( one cutting ed ge )
  • gouge S-1, 60° ( one cutting edge )
  • gouge N2-20, 60° ( two cutting edges )
  • gouge N3-20, 60° ( right router, left cutting edges )
  • gouge N4-20, 60° ( left router, right cutting edges )
  • gouge for corners 60° (or Carving chisel, PETROGRAD, V-type, 60 degrees)
  • Checkering layout guide / butt scribe
  • Checkering gauge
  • Roll bag for carving tools ( 6 pockets )

Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools: 8 tools
Type of checkers: 60 degrees
Number of lines: 20 lines on 1 inch
Handle material: Beech*
Handle lenght: 120 mm
Total lenght: 240 mm
Total weight: 0.4 kg
9000p(0)
Отзывов: 1
Рейтинг :
new

Checkering set, type N1, 90°/16lines, 6 tools + gauge, in roll bag

Checkering Set N1 (90 degrees, 16 lines) includes 6 tools for making checkers on wood. Set of gouges with 90 degree cutters, this type is making more sharp pointed checkers that grants stronger grip.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 90° ( one cutting edge )
  • gouge N2-16, 90° ( two cutting edges )
  • gouge N3-16, 90° ( right router, left cutting edges )
  • gouge N4-16, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • Checkering gauge
  • roll bag for carving tools ( 6 pockets )

Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tools made by Petrograd toolworks in Saint Petersburg Russia.

Number of tools: 6 tools
Type of checkers: 90 degrees
Number of lines: 16 lines on 1 inch
Handle material: Beech*
Handle lenght: 120 mm
Total lenght: 240 mm
Total weight: 0.3 kg
6300p(0) out of stock
Отзывов: 1
Рейтинг :

Checkering set, type N1, 90°/18lines, 6 tools + gauge, in roll bag

Checkering tool Set N1 (90 degrees, 18 lines) includes 6 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 90 degree cutters, this type is making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 90° ( two cutting edges )
  • gouge N3-18, 90° ( right router, left cutting edges )
  • gouge N4-18, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • roll bag for carving tools ( 6 pockets )
  • Checkering gauge
Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools:6 tools
Type of checkers:90 degrees
Number of lines:18 lines on 1 inch
Handle material:Beech*
Handle lenght:120 mm
Total lenght:240 mm
Total weight:0.3 kg

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.

6300p(0)
Отзывов: 1
Рейтинг :

Наборы для чекеринга

Видеоматериалы

youtube video
youtube video

Нож для резьбы по дереву, ПЕТРОГРАДЪ, Богородский, 200мм/60мм

Нож резчицкий ПЕТРОГРАДЪ, Богородский, 190мм/60мм. Резчицкие ножи общего назначения, а также для большого удаления материала. Отличный нож как для начинающих так и для профессионалов. Все ножи заточены и готовы к работе.
Для выбора нужного ножа нажмите на название товара
2700p
Отзывов: 1
Рейтинг:

Нож для резьбы по дереву, ПЕТРОГРАДЪ, финский, 180мм/40мм

Резчицкие ножи с острым кончиком предназначены для деталировки и работы в труднодоступных местах. Длина лезвия 45мм или 60мм, скругленный обух. Угол заточки 23±2°. Удобная овальная рукоять из ценных пород древесины, покрыта маслом. Длина рукояти - 115мм. Отличный нож как для начинающих так и для профессионалов. Лезвие толщиной 2,5мм выполнено из высокоуглеродистой стали с закалкой до твердости 59-61 HRc. Все резцы заточены и готовы к работе. Производство Петроград (Россия).
Для выбора нужного ножа нажмите на название товара
2500p
Отзывов: 1
Рейтинг:

Резец для чекеринга C-1, 60° (одна РК)

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Резец для чекеринга C-1, 90° (одна РК)

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Топор кованый ПЕТРОГРАДЪ, модель Рославль 7, топорище н11, РК - сканди

Топор кованный походный с изогнутой рукоятью. Общая длина - 370 мм. Высота топора - 140 мм. Длина режущей кромки - 120 мм. Топор выкован вручную из стали 65Г. Заточка прямая. Общая масса - 0,7 ± 0,05 кг. В комплекте кожаный чехол для защиты лезвия. Топорище выполнено из древесины клёна, длиной 320 мм. Топор отлично сбалансирован и подойдет для огромного вида работ, как походный топор, для небольших плотницких и столярных работ и просто как универсальный топор. 

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

13000p
Отзывов: 1
Рейтинг:
new

Нож для резьбы по дереву, ПЕТРОГРАДЪ, Ложкорез, модель N1/22, левый

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3200p
Отзывов: 1
Рейтинг:
new

Нож для резьбы по дереву, ПЕТРОГРАДЪ, флажок 45град, 180мм/40мм

Нож для резьбы по дереву, ПЕТРОГРАДЪ, косая заточка 45град. Предназначен для широкого спектра работ. Рукоять выполнена из ясеня, угол скоса 45 градусов, инструментальная сталь. Производство фабрика Петроградъ (Россия).

2500p
Отзывов: 1
Рейтинг:

Стамеска ПЕТРОГРАДЪ, серия Нева, 6мм

Стамеска ПЕТРОГРАДЪ, серия Нева, 6мм. Стамески спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков. Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при подрезке и подчитки шиповых соединений: ласточкин хвост, шип-проушина, впол дерева, сковородней и прочие. Производятся с различной шириной полотна от 3мм до 26мм. Толщина лезвия переменная и увеличивается от режущей кромки к рукояти. Производство фабрика Петроградъ (Россия)

3300p
Отзывов: 1
Рейтинг:
new%

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25. Отличается от других топоров удлиненной режущей кромкой. Благодаря этой особенности топор можно брать близким к полотну хватом и не бояться поранить руку при работе. Такой хват очень удобен при тёске и ошкуривании бревен. Удлиненная рукоять позволяет без лишних усилий рубить ветки и сучья. Производство фабрика Петроградъ (Россия).

15000p
Отзывов: 1
Рейтинг:
new

Масло камелии, KAPLEUM, Лаванда, 60 мл.

Масло камелии, KAPLEUM, Лаванда, 60 мл. Неформальная творческая группа GILDIA.PRO предлагает новый продукт, изготовленный на основе отлично зарекомендовавшего себя масла Камелии – KAPLEUM.

 

720p
Отзывов: 1
Рейтинг: