Wooden rabbet hand plane is light and all round good for tool making and other woodwork.

• The sole is made of hornbeam wood, main body made of maple and soaked with tung oil.
• Blade dimensions: width 20 mm, total length 175 mm, skew angle ~10 degrees.
• Blade maximum thickness 3.4 mm, minimum shank thickness 2 mm, shank width 5.5 mm.
• Blade set angle is 55 degrees (Middle Pitch).
• The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC.

 All blades are wedge-shaped with an angle of 0.5 degrees. This form is favorably distinguishes this blades from other blades on makret. This form isperfect suited for wooden planes with wedge fixation.

Blades have two sides: one is hard, the other is soft (production feature).
Every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.
Hand planes had manufactured by Petrograd toolworks in Saint Petersburg Russia.

Classic bench plane with brass cap and wedge shaped blade. This is a common wooden hand plane for surface flattening. Sole of hand plane was made of hard wood. We had replace the wooden wedge with brass cap mechanism for more secure fix and for minimizing vibrations of hand plane blade during the work.

• lenght of sole - 230mm
• width of blade - 50mm

Fixing cap is mounted on a strong steel stud, the knob acts as a lever. This design of the clamping cap allows for quick and accurate adjustment of the blade overhang. Body of hand plane was coated with oil. Blade installation angle - 50 °. The blade made of alloy tool steel and hardened to a hardness of 59-61HRC.

• blade installation angle - 50 °
• blade dimensions: length - 175mm
• blade width - 50mm
• blade shape - wedge
• The minimum thickness of the blade is 2.2 mm, the maximum thickness is 3.5 mm
• The blade sharpening angle is 25 ° and the micro chamfer on the edge is 30 °

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil and wax. The wedge is also made of maple. The installation angle of the knife is 50°. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 65 mm, knife thickness minimum 3.5 mm, maximum thickness - 4.8 mm. Sharpening angle 25° with microbevel 30°. Dimensions of jointer plane 600 * 90 * 175 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil and wax. The wedge is also made of maple. The installation angle of the knife is 50°. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 65 mm, knife thickness minimum 3.5 mm, maximum thickness - 4.8 mm. Sharpening angle 25° with microbevel 30°. Dimensions of jointer plane 780 * 90 * 175 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

This shoulder plane can be used both for making a groove or a quarter, as well as for easy processing of edges and areas of abutment of parts to each other in the assembled state. The block is made of maple, the wedge is made of mahogany and soaked with tung oil. The width of the knife is 20 mm, the angle of inclination of the bed to the sole is 45 degrees. Absolutely every knife is tested with a hardness tester. The solid side has 2 points from the diamond cone - the test, and the control test. The knife has the following dimensions: the width of the working part is 20 mm, the angle of grinding is 30 degrees, the maximum thickness is 5.2 mm, the minimum thickness of the shank is 4 mm, the total length is 175 mm. The blade is made of steel 9ХС (DIN - 150Cr14), hardened to 59-61 HRC. All blades are wedge-shaped with a wedge angle of 0.5 degrees.

Dimensions of plane: 175x130x20 mm.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Traditional wooden small plane, the so-called "apron hand plane". This small hand plane uses for various types of work, it is always at hand, fit in the pocket of your clothes or apron.

• body of hand plane is made of hornbeam
• wedge made of mahogany
• hand plane dimensions: 150x45x69 mm
• coating - oil and wax

Blade installed in hand plane body with 45 degrees angle and fixed by wooden wedge.

• blade was made of alloyed tool steel 9XC (DIN - 150Cr14)
• hardned to 59-61 HRC.
• blade length - 79 mm
• blade width - 30 mm
• blade shape - wedge
• blade thickness minimum 4.8 mm
• maximum thickness - 5.2 mm.
• sharpening edge is 30 °

All PETROGRAD hand plane blades have a wedge-shaped descent with an angle of 0.5 degrees. This distinguishes them favorably from other plane blades, and makes them ideal for wooden planes with a wedge fixation. The working side of the knife, hardened to a hardness of 59-61 HRc, is marked with small indentations, which remain from the hardness gauge after checking the knife. These recesses, which are located on each blade, are evidence of checking blades and do not affect the performance of the product.

IMPORTANT! The reverse side of the knife, not marked with control points, is not working!
The manufacturer reserves the right to change the thickness of the knife without degrading the working qualities of the tool.

Hand made by Petrograd toolworks in Saint Petersburg Russia.

Circular Plane PETROGRAD with convex edge is intended for making of curvilinear surfaces. The body of the plane is made of maple and has an insert of brass for reliable fixation of the blade. Coating - tung oil. The wedge is also made of maple. Dimensions of plane 200*80*46 mm. Buckling radius 650 mm. Cross bend radius 250 mm.

The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 110 mm, width - 30 mm, thickness minimum 3.2 mm, maximum thickness - 4.5 mm. Radius of the cutting edge of a blade 50 mm. Sharpening angle 30°.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Circular plane PETROGRAD with straight cutting edge is intended for making of curvilinear surfaces. The body of the plane is made of maple and has an insert of brass for reliable fixation of the blade. Coating - tung oil. The wedge is also made of maple. Dimensions of plane 200*80*46 mm. Buckling radius 650 mm.

The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 110 mm, width - 30 mm, thickness minimum 3.2 mm, maximum thickness - 4.5 mm. Sharpening angle 30 °. 

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Рубанок-граттубель ПЕТРОГРАДЪ. Предназначен для легкого и быстрого создания соединения "скользящий ласточкин хвост". Тело рубанка выполнено из клёна. Нож изготовлен из стали 9ХС, закален до 61 HRC. Производство фабрика Петроградъ (Россия).

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil. The wedge is also made of maple. The installation angle of the knife is 50 ° -55 °. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 60 mm, knife thickness minimum 2.2 mm, maximum thickness - 3.5 mm. Sharpening angle 30 °. Dimensions of jointer plane 455 * 80 * 170 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

The tool of choice for major stock removal, a scrub is not usually used parallel to the grain, but at an angle of 30° or more. The blade edge is ground with a radius, so it takes an aggressive cut. This is the tool to use to get stock into a condition where you then can use a smooth plane.

The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 30 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Рубанок шерхебель с шириной ножа 50 мм, используется для промежуточного строгания между одинарным рубанком и шерхебелем с шириной ножа 30 мм. Благодаря широкому ножу с полукруглой режущей кромкой такой рубанок способен легко срезать большой объем материала, при этом сглаживая более грубые риски предыдущего рубанка. Это усовершенствованная модель рубанка комплектуется латунным прижимом с оригинальной гравировкой фабрики производителя. Производство фабрика Петроградъ (Россия)