Petrograd Carbide Burnisher, type 1, d3mm*20mm

Burnisher tool for card scrappers. Designed to set burr on curl and straight scraping cards. Pin made of silicon carbide and secured by the compound. Handle made of maple wood, reinforced with a brass ring and oil coated.

  • silicon carbide pin
  • pin diametre is 3.2mm
  • maple handle

The small dimensions and small diameter of the steel pin will be convenient when setting burr on small concave or straight card scrapers. Production of Petrograd toolworks. Made in Saint-Petersburg Russia.

* scraper is not included in the package.

900p(13.84)
Отзывов: 1
Рейтинг :
new

Petrograd Carbide Burnisher, type 1, d8mm*135mm

Наводка для цикль, ПЕТРОГРАДЪ, модель 1, рабочая часть D8мм*150мм. Предназначена для наведения грата на столярных циклях. Длинный стержень диаметром 8ии и удобная рукоять будут удобны при наводке как больших фигурных, так и прямых цикль.
1800p(27.68) out of stock
Отзывов: 1
Рейтинг :

Cabinet scraper PETROGRAD, 100*40*0.8mm

Designed for scraping wood. This is a simple yet highly effective tool. It allows you to process twisted areas of wood, leaving behind a perfectly smooth surface. Also ideal for removing old paintwork and adhesives. Unlike sandpaper, the rectangular scraper does not fill up the edges or clog the pores of the wood. After processing the cycles, finishing materials can be applied. Before using the cycle, it is necessary to align the planes and sharpen the ends, and then set the burr (burr). For burr aiming, we recommend using the special aiming Petrograd. The plate is made of carbon steel, 0.8 mm thick. The guide for the cycle is not included in the package.
Production of the factory of joinery and carpentry tools PETROGRAD

300p(4.61)
Отзывов: 1
Рейтинг :
%

Cabinet scraper PETROGRAD, 150*50*0.8mm

Dimensions: 50 x 150 x 0.8 mm. Carbon tool steel. Made in Czech Republic.

240p(3.69) out of stock
Отзывов: 1
Рейтинг :
new

Card scraper PETROGRAD, 150*65*0.8mm

Woodworking card scraper, square shape. Designed for scraping wood. Square card scraper made of carbon steel. Edge of carbon steel scraper can be prepared for turning the burr for clean cutting.

  • carbon steel
  • square shape
  • square edges
  • thick is 0.8 mm (0.031 inch)
  • lenght 150 mm (5.91 inch)
  • width 65 mm (2.56 inch)
Made at Petrograd toowlorks in Saint-Petrsburg Russia.

* Before using the cabinet scraper, we recomend to finish align the planes and sharpen the ends of card. After that ypu can set a burr on edge of card scraper for clean and smooth cuts. For burr aiming, we recommend using a burnisher by Petrograd toolworks.

** The burnisher guide is not included in the package.

Card scraper - a woodworking shaping and surface finishing tool. It is used to manually remove small amounts of wood without tear out, a specialy on tricky grain. Card scrapers are most suitable for working with hardwoods.

Profile: Square
Lenght: 150 mm
Width: 65 mm
Thick: 0.8 mm
Weight: 70 gramm
400p(6.15)
Отзывов: 1
Рейтинг :
new

Card scraper PETROGRAD, 128*63*0.8mm

Цикли прямоугольные ПЕТРОГРАДЪ. Ручная цикля для дерева, прямоугольная. Цикля предназначена для обработки древесины и лакокрасочных изделий. Ручная цикля это простой, но очень эффективный инструмент. Пластина цикли выполнена из углеродистой стали, толщиной 0.8 мм. Производство Петроград (Россия)
400p(6.15) out of stock
Отзывов: 1
Рейтинг :
new

Цинубка 20мм

Цинубка 20мм – это незаменимый инструмент для фанерования. Он позволяет вам проделать на склеиваемых поверхностях риски, за счет которых будет увеличена площадь соприкосновения, что даст более прочный клеевой шов. Производство Россия.

2550p(39.22)
Отзывов: 1
Рейтинг :

Cabinet scrapers

Hand planes by Petrograd toolworks(Russia) are beautiful and unsurpassed quality piece products for true connoisseurs of handicraft. All components are manufactured and processed by real professionals in their field.

All plane blades maded localy, have a wedge-shaped descent with an angle of 0.5 degrees. This sets them apart from other blades and makes them ideal for wedge-retained wooden planers.
The working side of the blade, hardened to a hardness of 59-61HRc, is marked with small holes remaining from checking with a hardness tester. These notches, which are present on each blade, are evidence that the blade had been checked and do not affect the performance of the product.

Hand plane body are made of selected wood, cured and only then processed by highly skilled craftsmen. You can see the work on the production of our planers on YouTube and in the company's social networks.

The assortment of hand planes by Petrograd toolworks is constantly replenishing and today it has 28 models of planes, ranging from classic smoothing planers to exotic types: router planes, rabbet planes and moulding type planes and etc.

By purchasing a hand plane by Petrograd toolworks, you are buying a high-quality and reliable thing that will serve and delight you for years.
new

Strop PETROGRAD, two-sided, 200mm*70mm

Double-sided bar with glued leather. The size of the bar is 200x70x25mm. It can be used with polishing pastes. Material - ash, leather - "reversal" 2mm. Skin color may differ from the image on the site. Made in Russia.

950p
Отзывов: 1
Рейтинг:

Strop PETROGRAD, for carving tools, 150mm*30mm

The bar with glued leather is designed for finishing semi-circular chisels, drawknives, etc. One of the flat sides can also be used for fine-tuning of flat tools. The size of the bar is 150x30 mm. Min radius - 3 mm, max. radius -6 mm. It can be used with polishing pastes. Material - ash, leather - reversal 2mm. Leather color may differ from the image on the site. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Checkering tool complete B-2

Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Leather 16 pocket Tool Roll, PETROGRAD

Leather tool roll PETROGRAD. The bag is made of a brown split is designed for storing and carrying carving and bench chisels with a handle diameter of not more than 35 mm and a total length of not more than 260 mm. The bag is equipped with ties for fixing the bag in a twisted state. Width 320 mm, total length in unfolded state 520 mm. The location of the pockets is two-sided. We recommend placing chisels in a bag with protective caps put on cutting edges.

The manufacturer reserves the right to make changes in the design of the bag that do not lead to deterioration of its qualities.

Made in Russia.

3600p
Отзывов: 1
Рейтинг:

Petrograd Bevel Gauge, 85mm*55mm

Шаблон угломер ПЕТРОГРАДЪ. 13 вырезов под углы - 15°, 20°,22.5° 25°, 27.5°, 30°, 32.5°, 35°, 37.5°, 40°, 45°, 90°, 120° глубина вырезов - 9 мм. Ширина шаблона - 54 мм, Длина шаблона 85 мм. На конце вырезов имеется отверстие, что позволяет использовать шаблон для определения других углов проводя интерполяцию (н-р угол 24° или 26°, используя вырез на 25°). Выполнен из латуни. Удобный и компактный шаблон используется для проверки углов при заточке стамесок, резцов, ножей рубанков и тп.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России.

1200p
Отзывов: 1
Рейтинг:
%

Polishing Paste 1200 grit 180 g

Waxy polishing pastes in the form of a rectangular bar. Dimensions - 60x60x15mm. Granularity - coarse, medium and fine. Brown 1200grit Weight - 180g. Used for grinding and polishing on wheels, belts, etc. Perfect for hand-held leather bars Petrograd.

Ingredients: a mixture of grinding powders, binders and auxiliary elements kerosene, stearin, sodium bicarbonate, silica gel.

Made in Russia.

720p
Отзывов: 1
Рейтинг:

Checkering tool complete T-24, 60°

Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.

At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

850p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 120 grit

Abrasive water stones. Grit: 120, 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

1800p
Отзывов: 1
Рейтинг:
new

Checkering set, type N1, 90°/16lines, 6 tools + gauge, in roll bag

Checkering Set N1 (90 degrees, 16 lines) includes 6 tools for making checkers on wood. Set of gouges with 90 degree cutters, this type is making more sharp pointed checkers that grants stronger grip.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 90° ( one cutting edge )
  • gouge N2-16, 90° ( two cutting edges )
  • gouge N3-16, 90° ( right router, left cutting edges )
  • gouge N4-16, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • Checkering gauge
  • roll bag for carving tools ( 6 pockets )
6100p
Отзывов: 1
Рейтинг:
new%

Carving knife PETROGRAD, model Hatchet N6

Инструмент представлен линейкой штихелей с расширяющимся клинком с шириной рабочей части 27 мм, 38 мм, 43 мм. Имеют широкий спектр применения при резьбе, является одним из основных ножей в геометрической резьбе, а также удобен и востребован в технике резьбы Whittling. Штихели выполнены из стали 9ХФ и имеют рукояти из клёна, покрытые тунговым маслом. угол заточки - 20 градусов, толщина клинка - 2 мм.
Сделано в России.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ

1400p
Отзывов: 1
Рейтинг: