new

Straight Gouge Rubankov, N2, 12mm

Carving chisel "Rubankov" Straight Gouge N2, 12mm (0.47inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 12mm (0.47 inches). The total lenght of the gouge is 280mm (11.02inches), blade lenght is 145mm (5.71inches), the lenght of the handle is 135mm (5.31inches). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood (may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

3400p out of stock
Отзывов: 1
Рейтинг :
new

Workbench 1060*500 mm, with tray, front vise - HV515, side vise - HV582

The dimensions of the workbench are 1060x500mm, the thickness of the board is 40mm. Strapping board 120mm high with dovetail connections. Front (front) vice and rear (longitudinal) vice are installed on the workbench. The front vise is made on the basis of a metal screw pair from York (Czech Republic), opening width - 225mm. The width of the movable jaw of the front vise is 350mm, the height is 110mm, and the thickness is 50mm. Longitudinal vise - sliding cracker. Made on the basis of a York screw with metal guides. This vice allows you to clamp workpieces not only for longitudinal planing, but also for sawing box spikes. Longitudinal vise stroke - 145mm. The jaw of the vise and the jaw of this model are straight, not decorated. To install the stops, a row of holes was drilled in the tabletop, 11 pieces, +2 hole was drilled in a cracker. In the strapping board on the working side, 3 horizontal holes for the stops are also drilled. Hole diameter - 19mm. At the back of the workbench there is a tray for small tools, tray depth - 35mm, width - 180mm, length - 980mm. To strengthen the pedestal between the legs, an additional upper pair of longitudinal crossbars is installed. The material of the workbench is a beech board, the pedestal and handles are solid beech. The worktop and the base are coated with Borma tung oil. The workbench must be installed on a flat horizontal surface to avoid warping and deformation of the workbench. The size of the pedestal is 1060x500x800mm, the section of the legs is 90x45mm. Workbench height - 850mm. The weight of the workbench is about 50kg. There are 2 configuration options available to order: a workbench with a pedestal and a separate workbench. Small changes may be made to the workbench design without affecting its quality. Bench stops are sold separately. All workbenches manufactured by Rubankov can be equipped with additional vertical vise and support board. The workbench can also be completed with a sub-bench for tools. Production - Rubankov workshop (Russia)
62000p out of stock
Отзывов: 1
Рейтинг :
new

Stright Gouge Rubankov, N8, 20mm

Carving chisel "Rubankov" Straight Gouge N8, 20mm (0.79 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 20mm ( 0.79 inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

3500p out of stock
Отзывов: 1
Рейтинг :
new

Marking knife PETROGRAD, model N5, skew form

Marking knife N5, right bevel. This knife is a carpentry tool for precision marking, it has one-sided sharpening. Blade of marking tool is made of high carbon steel and hardened. Best for marking woodwork joints, may be used for cutting veneer.

Knife blade was sharpened and ready to work out of the box.

  • high carbon steel
  • hardened to 59-61 HRc
  • blade length - 23mm
  • blade thickness - 2.3mm
  • sharpening angle - 30 degrees
  • skew angle - 40 degrees
1200p
Отзывов: 1
Рейтинг :
new

Straight Gouge Rubankov, N45, V-tool 90 degree, 12mm

Straight Gouge Rubankov, N13, V-tool 90 degree, 12mm. Professional grade carving tools designed for hard and soft wood carving. The basis of any set of cutting tools is the corners. Corner chisels are suitable for a variety of tasks: creating curly shapes, decorating wooden surfaces, prescribing patterns in geometric carvings.

RUBANKOV corner chisels are forged from low alloy high carbon steel.
The faceted handle is made of fine wood and coated with oil. The striking side is rounded to avoid corns on the palms. The brass ring gives a sophisticated look and prevents the handle from cracking when working with a mallet. The inner profile of the chisel is polished, the cutting edge is sharpened and ready to work.
These models are percussion models, they can be paired with a mallet.
The stated geometric dimensions may vary slightly, since the tool is manufactured and sharpened by hand.

The length of the metal blade is 145mm.
Total length with a handle 280mm.
Blade width - 12mm.
The angle of the internal profile of the chisel is 90 degrees.
Angle of sharpening of the cutting edge (RK) - 25 degrees.
Hardened to 59-61 HRc.
Manufactured at the PETROGRAD joinery and carpentry tools factory.
Production Russia.
4200p out of stock
Отзывов: 1
Рейтинг :
new

Bevel edge chisel, PETROGRAD, model Volga, 26mm

Bevel edge chisel Volga. These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess.

  • blade lenght - 150 mm
  • blade width - 26 mm
  • blade is made of high-alloyed chrome-manganese steel
  • hardened to 59-61 HRc
  • basic edge angle - 25 degrees
3000p
Отзывов: 1
Рейтинг :
new

Log Scriber PETROGRAD

Log Scriber PETROGRAD. Suitable for all types of felling and carpentry work. The ability to quickly and securely attach a pencil of any shape (round, oval, hex), a gas rod, a metal probe-copier (2 pcs. In the set) - with a diameter of 5 to 13 mm. The opening angle is fixed with a lamb.
Dimensions 340x175x110 mm (LxWxH). Maximum opening (distance between tips) - 350 mm. Weight 0.74 kg.
15700p
Отзывов: 1
Рейтинг :
new

Basket Weaving Stright awl d6mm, PETROGRAD

Awl for basket weaving, straight needle. This tool is an essentional for basket weaving and used for easely weaving rods in rows. Straight weaving awl allow you to move apart the rows and weave additional elements into them, its especially necessary with openwork weaving. Needle made of steel, point is flatten. The handle is made of maple and covered with oil.

  • diametr - 6 mm
  • not sharp *
  • handle made of maple
  • oil covered

* basket weaving awl should not be sharp to not spoil the surface of the rods.

Production of the Petrograd toolworks. Made in Saint Petersburg Russia

Head weight: 0.63 kg
Full weight: 0.7 kg
Type: weaving awl
Steel: 65Г or so
Hardness: -
Handle material: Maple*
Handle lenght: 105 mm
Point: flatt
Blade lenght: 105 mm
Total lenght: 210 mm
 * material of handles may changes from batch to batch.
800p
Отзывов: 1
Рейтинг :
new

Book "Woodwork. Furniture for the home - projects and drawings", Mark Ripley

The book by the renowned British cabinetmaker and furniture designer is a complete, practical guide to furniture making with fresh, innovative approaches and professional tricks. The laconic lines of the author's furniture are very attractive, his projects are available for production by fairly experienced amateur carpenters and carpentry craftsmen. There are projects for every taste and every opportunity, from a simple dining table to a grandiose bookcase with a multi-level facade in the style of Robert Adam. This impressive collection of furniture designs includes: - Chairs - Tables - Chests of drawers and sideboards - Bookcases and kitchen cabinets - Home furnishings.
730p
Отзывов: 1
Рейтинг :
new

Sharpening stone PETROGRAD, D15mm*153mm, 240 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х153mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

650p
Отзывов: 1
Рейтинг :

Sharpening set PETROGRAD N1, for woodworking tools, 3 stones

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

5240p
Отзывов: 1
Рейтинг:
new

Carving set PETROGRAD, N2

The set includes:

Carving knife PETROGRAD, Bogorodsky type, 155mm/40mm
Carving knife PETROGRAD, Finnish type, 175mm/60mm
Carving knife PETROGRAD, skew 30 deg, 155mm/40mm
Carving knife PETROGRAD, Swedish type, 175mm/60mm
Spoon knife, PETROGRAD, D 27mm, right-handed
Carving chisel, PETROGRAD, 10mm
Textile 6 pocket Tool Roll, PETROGRAD, 360*260mm, for carving knives

 

 

 

 

9500p
Отзывов: 1
Рейтинг:

Carving adze PETROGRAD, type N1, half round, external bevel

Wood carving adze by PETROGRAD toolworks.

This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.

Developed and designed carving adze - V. Sasin.

The ergonomic handle allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.

Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool  - it is 9 profile.

The eye has a wedge shape. The adze handle slides and splits into 3 wedges.

Sharpening the cutting edge - chamfer outside. It is preferable to use this adze at the finishing stages, for stripping, for smooth formation of the transition from the vertical wall to the flat bottom.

Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

9200p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

3440p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, right-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The right version of knife is designed to work with the right hand towards yourself or left hand to outside.

  • Knife blade width - 12mm.
  • Spoon cutter length - 235 mm
  • Handle length - 160 mm
  • Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

2900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl VII, curved handle

Hand forged outdoor axe Roslavl VII with curved handle.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

10000p
Отзывов: 1
Рейтинг:

Checkering set, type N3, 90°/18lines, 10 tools + gauge, in roll bag

Set N3 (90 degrees, 18 lines) includes 10 tools  for making checkers on wood.

Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Set number 3 includes:

gouge B-2 ( two cutting edges, spacer with tooths )
gouge S-1 ( one cutting edge )
gouge N2-18, 90° ( two cutting edges )
gouge N3-18, 90° ( right router, left cutting edges )
gouge N4-18, 90° ( left router, right cutting edges )
gouge C-1, 90° ( one cutting edge )
gouge L- 9, 90° ( right router with wide space, left cutting edge )
gouge R- 9, 90° ( left router with wide space, right cutting edge )
gouge for corners 90° (or Carving chisel, PETROGRAD, V-type, 90 degrees)
gouge for marking rifle handles
checkering guage
roll bag for carving tools model N1 ( 12 pockets )

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.

12630p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 3000 grit

Water stones. Grain size: 3000 and 6000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Japan.

 

2950p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 6000 grit

Water stones. Grain size: 3000 and 6000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Japan.

 

4180p
Отзывов: 1
Рейтинг:

Фабрика Петроградъ ( Petrograd toolworks )

to up