Tool set for weaving rod

Special set of tools for weaving baskets from a vine or manufacturing other wickerwork products: home furniture and containers for various purposes, such as boxes, baskets, vases and other various utensils.
The vine is a natural plant material that can bend easily and keep its shape under normal conditions. Often the material for weaving is willow, rattan and bamboo.

All of the tools are pretty basic and easy to use.
Skew knives are the basis tool for basketry. Knives in this tool set comes with different shapes and thin blades. All knives well sharpened for pleasant work.

Next tools in set is various awls. Awl need to work with rows of rods. It allow you to move apart the rows and weave additional elements into them, especially with openwork weaving. The awl are dull for not to spoil the rods surface.

And last tool is basketry mallet. It used for tapped the rows for alignment.

The set includes:

  • Handicraft knife PETROGRAD, oblique sharpening 20 degrees, 20mm / 163mm, universal.
  • Handicraft knife PETROGRAD, 60 degrees, 12mm / 100mm, universal.
  • Handicraft knife 45 degrees, Denisov's model, oblique sharpening.
  • Curved awl for basket weaving D6mm.
  • Awl for wicker weaving straight D8mm
  • Mallet for weaving Ysere.
  • Bag-twist fabric, PETROGRAD, model 1, for cutting tools, 12 pockets.

We are also recommend to purchase some pruning shears.

Basket weaving tool set are produced at Petrograd toolworks in Saint-Petersburg Russia

6500p(99.97) out of stock
Отзывов: 1
Рейтинг :
new

PETROGRAD Basket Weaving Tool Kit, n1

For the manufacture of wickerwork from a vine: home furniture and containers for various purposes, such as boxes, baskets, vases and other various utensils. The vine is a natural plant material that can bend easily and keep its shape under normal conditions. Often the material for weaving is willow, rattan and bamboo.
All of the tools are pretty basic, simple, and affordable.
Knives are, of course, the main tools in weaving. But all other tools speed up and improve the quality of weaving, make products of higher quality. Knives are used in different shapes, with a good sharpening, thin blade.
Also, various awls are used to work with weaving. They are needed to work with rows. They allow you to move apart the rows and weave additional elements into them, especially with openwork weaving. The awl should not be sharp so as not to spoil the surface of the rods.
The rows are tapped with an yser or mallet.
The set includes:
Handicraft knife PETROGRAD, oblique sharpening 20 degrees, 20mm / 163mm, universal.
Curved awl for basket weaving D6mm.
Awl for wicker weaving straight D6mm
Mallet for weaving Ysere.
Handicraft knife PETROGRAD, oblique sharpening 60 degrees, 20mm / 187mm, universal.
Handicraft knife PETROGRAD, oblique sharpening 30 degrees, 20mm / 167mm, universal.
Bag-twist fabric, PETROGRAD, model 1, for cutting tools, 6 pockets.

It is also recommended to purchase pruning shears Shogun-355, length 210 mm.

Production of the PETROGRAD factory. Russia

6000p(92.28)
Отзывов: 1
Рейтинг :
new

Basket Weaving Tool Kit, n2, PETROGRAD

For the manufacture of wickerwork from a vine: home furniture and containers for various purposes, such as boxes, baskets, vases and other various utensils. The vine is a natural plant material that can bend easily and keep its shape under normal conditions. Often the material for weaving is willow, rattan and bamboo.
All of the tools are pretty basic, simple, and affordable.
Knives are, of course, the main tools in weaving. But all other tools speed up and improve the quality of weaving, make products of higher quality. Knives are used in different shapes, with a good sharpening, thin blade.
Also, various awls are used to work with weaving. They are needed to work with rows. They allow you to move apart the rows and weave additional elements into them, especially with openwork weaving. The awl should not be sharp so as not to spoil the surface of the rods.
The rows are tapped with an yser or mallet.

The set includes:
Shilo PETROGRAD, 165mm, straight blade 80 * 5 * 5mm
Awl for wicker weaving straight D6mm
Curved awl for basket weaving D6mm
Handicraft knife PETROGRAD, oblique sharpening 20 degrees, 20mm / 163mm, universal
Handicraft knife PETROGRAD, oblique sharpening 30 degrees, 20mm / 167mm, universal
Handicraft knife PETROGRAD, oblique sharpening 60 degrees, 20mm / 187mm, universal
Ysere vine weaving mallet
Polyurethane mallet PETROGRAD, model 1, D70mm, recoilless
Secateurs Kamaki, closed handle, 210 mm straight blade
Sharpening abrasive PETROGRAD, 120 * 15 * 15mm, 4000grit
Box 312 * 184 * 75, MGK brown 1.5mm (for planers)

Production of the PETROGRAD factory. Russia

14000p(215.32)
Отзывов: 1
Рейтинг :

Tool sets for Wickerwork

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1200p
Отзывов: 1
Рейтинг:

Mallet PETROGRAD, round, D65mm*250mm, 300 g

Wooden mallet, round shape. Solid wood mallets made by woodturning. Mallet weight 300 gramm. Mallets made of beech wood and covered with tung oil. Round mallets used for working with mortise chisels and woodcarving chisels. It used when cutting joints and when carving large elements or sculptures (work from under the mallet).
700p
Отзывов: 1
Рейтинг:

Adze PETROGRAD, half round N3

Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia

Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

9700p
Отзывов: 1
Рейтинг:

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

600p
Отзывов: 1
Рейтинг:

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 60 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 60 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 25mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 38mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6500p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 50mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

The blade has forged manually from steel ШХ15 (USA analog is 52100, G52986, J19965; Germany  analog of 1.3505, 100Cr6, 102Cr6) and hardened to 58-61 HRC. Carpentry chisels are intended for timber framing for processing deep grooves in logs and timber as an indispensable tool for the construction of frame structures in the style of timber frame, post-and-beam half-timbered, fachwerkhaus, Log house.

  • Chisel blade fastened to the handle with a conical socket.
  • The thickness of the blade at the neck is 11 mm, the thickness in the area of the descent is 7 mm.
  • The handles are made of ash and crimped with a stainless ring to harden the butt when working with a mallet or hammer.
  • Available in widths of 19 mm, 25 mm, 38 mm, 40 mm and 50 mm ( see full catalogue).
  • Blade length 300 mm, full length 410 mm.
  • The wedge-shaped blade prevents jamming in the wood.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7000p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 38mm

Forged carpentry chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7600p
Отзывов: 1
Рейтинг: