Apron RUBANKOV, model 4, light-brown

Фартук Столярный Rubankov кожаный, светло-коричневый. Длина фартука - 800 мм, ширина - 680 мм. Нагрудный карман c 1 отделением. Размеры нагрудного кармана - длина 150 мм, ширина 175 мм. Лямки и поясной ремень оборудованы застежками и пряжками. Цвет фартука - светло-коричневый. На фартук нанесен логотип Rubankov. Материал - 100 % натуральная кожа, металлическая фурнитура.
Сделано в России.

10500p(161.49)
Отзывов: 1
Рейтинг :

Apron RUBANKOV, model 3, dark-brown

Фартук RUBANKOV, модель 3, тёмно-коричневый блестящий. Фартук выполнен из высококачественной кожи, чуть ниже колен, с передним разрезом для удобства работы. Верхняя лямка легко и быстро регулируется по длине. Нагрудный карман под карандаши, ручки, маленькую линейку или рулетку. Также имеется нижний сквозной карман. Для различного небольшого подручного инструмента или просто место отдыха для рук. Карманы прошиты и проклепаны латунными заклепками для усиления. Кожаный фартук это средство индивидуальной защиты. Предохраняет вас и вашу одежду от загрязнений и повреждений.

Производство фабрики Петроградъ

7200p(110.74)
Отзывов: 1
Рейтинг :

Apron RUBANKOV, textile, light-brown

Фартук Столярный Rubankov, тканевый. Длина фартука - 770 мм, ширина - 680 мм. Фартук надевается на плечи с крестообразным перехлестом ремней на спине, что обеспечивает плотное прилегание фартука к груди и не создает нагрузки на шею.У фартука три накладных кармана. Первый нагрудный карман с клапаном и фиксацией на кнопку для телефона ширина 90 мм длина 170 мм. Второй нагрудный карман для мелочей с 4 секциями для хранения карандаша, линейки, ширина 120 мм длина 130 мм. Третий карман для хранения мелочей или небольшого рубанка, рулетки или другого небольшого ручного инструмента. Ширина кармана 200 мм длина 190 мм. Одна петля под молоток. Лямки и поясной ремень имеют застежки и пряжки. Цвет фартука - бежевый. На фартук нанесен логотип Rubankov.

Материал - 100 % хлопок
Сделано в России

4500p(69.21)
Отзывов: 1
Рейтинг :
new

Apron, model 7, green textile

Apron model 7, green fabric. Apron length - 900 mm, width - 570 mm. The apron is worn on the shoulders with a cruciform overlap of the straps on the back, which ensures a snug fit of the apron to the chest and does not put stress on the neck. The apron has a patch pocket for small things with 4 sections for storing a pencil, ruler, tape measure and other small accessories. Leather straps are threaded through the waist rings and tied at the back. The apron color is green. The apron has the Rubankov logo. Material - 100% cotton
Made in Russia

3000p(46.14)
Отзывов: 1
Рейтинг :

Apron PETROGRAD, model 1, yellow

Apron PETROGRAD, model 1, yellow. The apron is made of high quality suede leather, up to the knees. With a front slit for easy handling. The apron is worn over the shoulders with a cruciform overlap of the straps on the back, which ensures a snug fit of the apron to the chest and does not put stress on the neck. Easily adjusts to any waist and ties at the pin. Front pocket sewn on from the inside to prevent chips from entering it. Convenient and reliable brass fittings. The apron has an embossed logo on the right side. The belts are stitched and additionally riveted.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia.

6000p(92.28)
Отзывов: 1
Рейтинг :
new%

Фартук ПЕТРОГРАДЪ, модель 1, коричневый

Фартук ПЕТРОГРАДЪ, модель 1, жёлтый. Фартук выполнен из высококачественной замшевой кожи, до колен. С передним разрезом для удобства работы. Фартук надевается на плечи с крестообразным перехлестом ремней на спине, что обеспечивает плотное прилегание фартука к груди и не создает нагрузки на шею. Легко подгоняется под любую талию и завязывается на пине. Спереди карман пришитый изнутри, для предотвращения попадания в него стружки. Удобная и надежная фурнитура из латуни. На фартуке с правой стороны есть тесненный логотип. Ремни прострочены и дополнительно собраны на заклепку. 

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ. 

Сделано в России.

5360p(82.44) out of stock
Отзывов: 1
Рейтинг :

Aprons

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1200p
Отзывов: 1
Рейтинг:

Mallet PETROGRAD, round, D65mm*250mm, 300 g

Wooden mallet, round shape. Solid wood mallets made by woodturning. Mallet weight 300 gramm. Mallets made of beech wood and covered with tung oil. Round mallets used for working with mortise chisels and woodcarving chisels. It used when cutting joints and when carving large elements or sculptures (work from under the mallet).
700p
Отзывов: 1
Рейтинг:

Adze PETROGRAD, half round N3

Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia

Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

9700p
Отзывов: 1
Рейтинг:

Checkering layout guide / butt scribe

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

600p
Отзывов: 1
Рейтинг:

Checkering tool complete B-1

Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.

Maximum roller height 1 mm, width 2.5 mm
Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 60 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 60 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 25mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6000p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 38mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

6500p
Отзывов: 1
Рейтинг:

Bench Chisel, PETROGRAD, model Istra short, 50mm

Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

The blade has forged manually from steel ШХ15 (USA analog is 52100, G52986, J19965; Germany  analog of 1.3505, 100Cr6, 102Cr6) and hardened to 58-61 HRC. Carpentry chisels are intended for timber framing for processing deep grooves in logs and timber as an indispensable tool for the construction of frame structures in the style of timber frame, post-and-beam half-timbered, fachwerkhaus, Log house.

  • Chisel blade fastened to the handle with a conical socket.
  • The thickness of the blade at the neck is 11 mm, the thickness in the area of the descent is 7 mm.
  • The handles are made of ash and crimped with a stainless ring to harden the butt when working with a mallet or hammer.
  • Available in widths of 19 mm, 25 mm, 38 mm, 40 mm and 50 mm ( see full catalogue).
  • Blade length 300 mm, full length 410 mm.
  • The wedge-shaped blade prevents jamming in the wood.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7000p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 38mm

Forged carpentry chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

7600p
Отзывов: 1
Рейтинг: