Масло ПЕТРОГРАДЪ ,для верстаков и рукоятей инструментов, 0.5л

Share / Save Link:

Oil PETROGRAD for workbenches and tool handles, 0.5l



820 p (11.38)
Rating :
Avg. value 0 (by rates of 0 users)

Description

Масло отделочное ПЕТРОГРАДЪ для верстаков и рукоятей инструментов, 0.5л. Грунтовочное, используется для нанесения первого слоя перед финишной отделкой. Рекомендуется для использования на твердой или хорошо впитывающей древесине. Рекомендуется для верстаков, столов, рукоятей, деревянных инструментов обработки и других деревянных деталей. Только для эксплуатации внутри помещений. Быстро и глубоко проникает в материал и также быстро полимиризуется.
Состав:
Масло тунговое, масло льняное, модифицированные масла (льняное, тунговое, сафлоровое, грецкого ореха), рициновое масло, воск карнаубский, микронизированный воск.
Способ применения:
На очищенную от грязи и обезжиренную подготовленную поверхность равномерно нанесите масло используя кисть или безворсовую ткань. Через 10 мин удалите остатки масла с поверхности сухой безворсовой тканью. По прошествии 8 часов (зависит от толщины слоя и окружающей температуры) нанесите второй слой покрытия. Необходимо обеспечить хорошую вентиляцию помещения, как при нанесении, так и по окончании работ.
Примечание:
Некоторые маслянистые, экзотические или ярко окрашенные породы древесины и излишнее количество могут препятствовать высыханию масла или сильно замедлить процесс сушки. В этом случае необходима хорошая вентиляция для ее ускорения.
- Не использовать для работы нитриловые перчатки.
- Безопасно для кожи рук
- При работе обязательно использовать защитные очки.
Хранение:
В герметичной таре. Его следует хранить вдали от источников огня и искр.
Производство - Россия.


l

Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

new

Журнал Мастер и мастерская 2020 2 (9)

300p(11.38) In stock

Bench chisel PETROGRAD. The length of the blade 120mm; width - 26mm. Overall length 250mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

1 530p

Set of bench chisels PETROGRAD. The length of the blade - from 120mm to 160mm; width - 6mm, 8mm, 10mm, 12mm, 16mm, 20mm, 26mm, 32mm. Overall length - from 250mm to 295mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

10 690p

Corner chisel PETROGRAD. Width of a blade is 10 mm. Used for final processing of grooves and angles of 90 degrees. Polished blade made from chrome-manganese steel, hardened to 56-58 HRc. The handle is made of a white hornbeam, which allows you to work both manually and with a mallet. The handle is compressed with a brass ring with a leather insert to prevent moisture ingress and for easy shock absorption. Included - plastic tip to protect the cutting edge. Blade length 120 mm, total length 255 mm. 

2 890p

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 170 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

3 300p

Marking knife PETROGRAD, with a flexible blade from steel 60SG2A (Germany 66Mn4, Ck67, USA 1066) is an ideal tool for marking the connections of the dovetail. The angle of formation of the arrow is 60 °, sharpening the blade with an angle of - 30 °. Blade thickness - 0.73mm, width - 9mm. Blade length - 40mm, knife length - 200mm. The handle is made of sapele wood covered with oil and shellac. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
900p

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
950p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

450p
new

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

4 910p
new%

Ножи-косяки с углом скоса 30 градусов. Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ. Длина лезвия указана в таблице, толщина клинка - около 2 мм. Лезвие  выполнено из стали 65Г с закалкой до твердости 59-61 HRc. Заточен и готов к работе. Ножи с косой заточкой имеют широкий спектр применения (в резьбе, для разметки, при работы с картоном, моделировании и в повседневной жизни, в быту). Нож комплектуется кожаным чехлом.

В настоящий момент идёт разработка дизайна модельного ряда резчицкого инструмента. Мы будем немного менять форму и размеры. 

Сделано в России

840p