Приспособление для заточки косых на гриндерах Robert Sorby и ПЕТРОГРАДЪ

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Forged corner carpenter chisel PETROGRAD 25*25 mm with a wooden handle are designed for hard work with wood. The blade is forged manually from steel ШХ15 (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6) and hardened to a hardness of 58-61 HRC. With the help of machining specified exact geometry. Designed for processing and cleaning the corners of deep grooves. The handles are made of ash and crimped with two stainless rings - one to prevent splitting wood near the handle, the second to harden the back of the bar when working with a mallet or hammer. A leather pad between the chisel and the grip allows you to dampen the blows. Available in 25 mm wide. Blade length 300 mm, total length 550 mm. The guarantee of 100% quality is a small hole on the back of the chisel - a trace from the diamond cone of the device for determining the hardness. This test passes every chisel.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.

• Blade width 120 mm
• Sharpening angle - 25 degrees
• Hardness - 55-58HRc
• Handle lenght - 350 mm
• Full weight - 07 kg

Carving axe Zvenigorod VII is quite small and easy to control. It's weight is about 650g, makes it maneuverable and allows you to work more accurate and precise.

The shape of the axe head was designed for carving operations where palm is resting extreamly close to axe head or even on the axe head. This design helps to exelent control of the axe even during long carving sessions. Grip above the head is used for trimming, stripping. This axe model was based on samples from museum "Rubankov" and finalized taking into account the wishes of wood carvers.

The axe head is hand forged from steel 65Г (spring steel) and hardened to 55 - 58 HRc at the cutting edge and along the entire beard, the rest part is normalized to HB280. This hardening allows you to hit the poll without the risk of creating a cracks in the metal.
Head has mounted to handle on 3 wedges, one along the head eye and two in cross section.

Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.

Axe handle is made of maple* and coated with Danish oil**. The hatchet handle has a longitudinal bend. In cross-section the handle has the shape of an egg, which is very convenient for good grip while carving. Handle has a hole for hanging.

Woodcarving axe Zvenigorod VII are product of Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.

Bent Gouge Rubankov, N7, 30mm (1.8 inches)

Carving chisel "Rubankov" Bent Gouge N7, 30mm ( 1.8 inches ). Perfectly suits for volume carving and deep hollow carving. The width of the cutting edge is 30mm ( 1.8inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

• Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
• All hook cutters are sharpened and ready to go.
• The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
• The handle of the hook knife is made of maple and coated with oil*.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

A set of blanks for making wooden spoons. The set includes two linden bars and 6 original patterns.

• Bars measuring 200x40x25mm and 200x30x22mm.
• Linden is a material for a beginner carver that does not require much work.
• Excellent sanding and tinting.
• Wood color is white.
• Great for subsequent painting.

Before starting work, it is recommended to copy the drawings for further use on other workpieces.

Wooden blanks by Petrograd toolworks. Made in Saint-Petersburg Russia.