Верстак  деревянный 980*260мм, настольный, Milkman's workbench

Share / Save Link:

Верстак деревянный 980*260мм, настольный, Milkman's workbench



11300 p (156.84) out of stock
Rating :
Avg. value 0 (by rates of 0 users)

Description

Деревянные винты при хранении и транспортировке оставлять не затянутыми во избежание коробления и повреждения при изменении влажности и температуры.Верстак настольный европейский Milkmans workbench Габариты: длина 980 мм, ширина 260 мм, толщина 40 мм. Верстак столярный из массива бука и украшен логотипом из бронзы, деревянные винты из граба и покрыты маслом. Данная модель деревянного верстака отлично подходит для домашней мастерской, при хранении практически не занимает места. Позволяет выполнять столярные проекты, заниматься резьбой по дереву. Для использования верстачную доску необходимо закрепить 2 струбцинами к любой плоской поверхности, для этого предусмотрены 2 монтажных отверстия с размерами ширина 35 мм, высота 14 мм глубина 30 мм l(для этого подходят два типа струбцин
Особенности конструкции: буковый щит собственного производства с симметрично размещенными двумя рядами монтажных отверстий под колки 19 мм. В комплектацию верстака входят 2 колка. С лицевой стороны верстачная доска имеет ряд отверстий (4 отверстия) с резьбой для установки винтов-прижимов. Диаметр деревянных винтов 25 мм. С торца установлены тиски с деревянным винтом и отверстием под колки 19 мм, губки которых закрыты кожаными накладками для предотвращения замятия заготовок.Обвязка собрана на прямой открытый шип-проушину и усилена нагелем из лиственных пород древесины.

Во избежание растрескивания и деформации верстачной доски, а также поломки деревянных винтов при транспортировке винты выкручены из верстака. Во фронтальные отверстия два коротких винта просто вкручиваются. Перед тем как установить длинный винт необходимо из сухарика выкрутить два самореза и вынуть две шпонки. Затем вкрутить деревянный винт до упора в сухарь и установить шпонки обратно, закрутить саморезы. Люфты сухарика и деревянных винтов сделаны для компенсации сезонных перепадов влажности. На рабочие качества и функционал не влияет, но предотвращает заклинивание подвижных элементов и излишнюю нагрузку на верстачную доску.
Верстак (Milkmans workbench) симметричный, две плоскости являются рабочими, то есть удобно пользоваться и левшам, и правшам.
Дополнительные характеристики настольного верстака:
Максимальная длинна зажимаемой в колках заготовки - 710 мм.
Габариты зажимаемой в тиски (сухарь) заготовки - 125x110 мм.
Габариты детали зажимаемой в продольные тиски с двумя винтами - 630х50 мм
Дизайн и исполнение мастер столярной мастерской RUBANKOV Сасин Владимир Иванович.
сделано в России.

l

Share / Save Link:

Видеоматериалы

Specs

Reviews

Instructions ()

Нет файлов

Publications

Bench chisel PETROGRAD. The length of the blade 120mm; width - 16mm. Overall length 250mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

1 340p

Bench chisel PETROGRAD. The length of the blade 120mm; width - 20mm. Overall length 250mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

1 370p

Set of bench chisels PETROGRAD. The length of the blade - from 120mm to 160mm; width - 6mm, 8mm, 10mm,12mm, 16mm, 20mm, 26mm, 32mm, 40mm, 50mm. Overall length - from 250mm to 295mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

14 970p

Set of firmer gouges PETROGRAD. The length of the blade from 120mm to 135mm; width -, 8mm, 10mm, 12mm, 16mm, 20mm, 26mm. Overall length - from 250mm to 295mm. The blade is made of high-alloyed chrome-manganese tool steel and hardened to 60HRc. The handle is made of hornbeam wood. The handle at the junction with the blade reinforced brass ring with leather gasket. Radius surfaces - black. Comfortable tool roll.

12 730p

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 170 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

3 300p

Flat U-shaped drawknife is designed for joinery, woodcarving, as well as for carpentry. Ideal for making Windsor chairs. Handles are in the same plane with the blade that allows easy control of the tool, and their direction at an angle to the cutting edge allows for less stress on the wrists.. The 3.5 mm thick blade has a straight cutting edge, made of carbon steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 57-59 HRC. Handles 100mm long made of maple, impregnated with oil and reinforced with a brass ring. Blade length - 135 mm, width 20 mm. Sharpening angle - 30grad. Includes leather case to protect the blade. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

 

3 000p
new

Carving knives with a bevel angle of 30, 37, 40 degrees double-sided sharpening. Blade length - 40 mm, width 13 mm, straight butt. A comfortable maple oval handle is saturated with oil and covered with shellac. The length of the handle - 115 mm. Knife for a wide range of works. The 2.5 mm thick blade is made of 65G (Germany 66Mn4, Ck67, USA 1066) steel,  hardened to 59-61 HRc. Sharpened and ready to go.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

900p
new

Mallet PETROGRAD, "barrel", striker size - mm D85
Excellent all-wooden mall weighing 500 g (error + -30 g)
The mallet is made of beech and covered with tung oil. The mallet has a barrel shape and a comfortable, chiseled, ergonomic handle. The handle is fixed on a wooden wedge. Mallets are widely used when working with bits and chisel chisels when cutting connections, as well as when carving large items or sculptures (work from the hammer).
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

770p

Outdoor axe. Total length - 440 mm. The length of the cutting edge 75 mm. The axe is forged by hand from 65G (Germany 66Mn4, Ck67, USA 1066) steel. Sharpening lens-shaped. Shock reinforced butt. Total weight - 0.9 kg. Includes leather case to protect the blade. The axe handle is made of maple wood. The axe is perfectly balanced and is suitable for cutting down, cutting off branches, driving wedges and other hiking needs. In Canada, supporters of rafting and canoeing called this axe - Canoe Axe. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia

 

7 400p
new

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

950p