Card scraper PETROGRAD, 150*65*0.8mm

Rating : (1)
Shipping: worldwide

From 400 p (6.15) out of stock


Woodworking card scraper, square shape. Designed for scraping wood. Square card scraper made of carbon steel. Edge of carbon steel scraper can be prepared for turning the burr for clean cutting.

  • carbon steel
  • square shape
  • square edges
  • thick is 0.8 mm (0.031 inch)
  • lenght 150 mm (5.91 inch)
  • width 65 mm (2.56 inch)
Made at Petrograd toowlorks in Saint-Petrsburg Russia.

* Before using the cabinet scraper, we recomend to finish align the planes and sharpen the ends of card. After that ypu can set a burr on edge of card scraper for clean and smooth cuts. For burr aiming, we recommend using a burnisher by Petrograd toolworks.

** The burnisher guide is not included in the package.

Card scraper - a woodworking shaping and surface finishing hand tool. It is used to manually remove small amounts of wood without tear out, a specialy on tricky grain. Card scrapers are most suitable for working with hardwoods.

Profile: Square
Lenght: 150 mm
Width: 65 mm
Thick: 0.8 mm
Weight: 70 gramm

Share / Save Link:



Instructions ()

Нет файлов


Recommended products

Стеллаж-витрина 2000*1000*500мм

Стеллаж-витрина 2000*1000*500мм предназначена для использования в торговых и выставочных залах. Надёжная конструкция обеспечивает хороший обзор и безопасное хранение экспонатов и образцов. Разборный каркас выполнен из массива бука и покрыт отделочным маслом. Каркас собран на шиповых соединениях с дополнительным усилением болтами. Раздвижные дверцы также выполнены из стекла толщиной 4мм. 
Количество полок - 5, размер поверхности - 900х400мм.
Три полки из пяти устанавливаются на полкодержатели, нагрузка на эти полки не должна превышать 10кг.
Допустимая нагрузка на полки, устанавливаемые на деревянные рамы - 20 кг.
Предусмотрена возможность устанавливать полки на разной высоте.
В боковые стойки встроены светодиодные ленточные источники света. Напряжение 220В, 50Гц.
Вес витрины около 85кг.
На заказ могут быть выполнены стеллажи любых других размеров.
Производитель оставляет за собой право вносить в конструкцию изменения, не влияющие на функциональность изделия.
Производство фабрики ПЕТРОГРАДЪ, Россия.

Отзывов: 1

carpentry Awl, 165mm, twisted blade 80*5*5mm, PETROGRAD

Carpentry power awl has a twisted square blade profile that allows you to mark the center of the holes and do not stray under the influence of wood fibers.

  • The blade is made of carbon steel and hardened in oil to HRC 55-60
  • Awl blade length is 80mm, the cross section is 5mm x 5mm
  • The shape of the handle allows you to abut the whole palm, compressed by a brass ring
  • Handle material - maple, impregnated with linseed oil
  • Full length 165mm

Carpentrs awl are produced at Petrograd toolworks. Made in Saint Petersburg Russia

Отзывов: 1

Carving adze PETROGRAD, type N1, half round, external bevel

Wood carving adze by PETROGRAD toolworks.

This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.

Developed and designed carving adze - V. Sasin.

The ergonomic handle allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.

Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool  - it is 9 profile.

The eye has a wedge shape. The adze handle slides and splits into 3 wedges.

Sharpening the cutting edge - chamfer outside. It is preferable to use this adze at the finishing stages, for stripping, for smooth formation of the transition from the vertical wall to the flat bottom.

Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

Отзывов: 1

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.


Отзывов: 1

Outdoor axe PETROGRAD, model Roslavl X, curved handle

Топор кованый ПЕТРОГРАДЪ, Рославль X, изогнутая рукоять. Топор Рославль Х отличается эффектной удлиненной формой полотна. Благодаря такой форме оголова топор можно брать хватом близким к полотну и не бояться повредить руку при работе. Изогнутая рукоять позволяет обеспечивает надежный захват. Плотницкий топор удобен при тёске и ошкуривании бревен. Также топор Рославль X отлично сбалансирован и подойдет для огромного вида работ, как походный топор, для не больших плотницких и столярных работ и просто как универсальный топор.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России.

Отзывов: 1

Outdoor axe PETROGRAD, model Roslavl VII, handle n11

Hand forged outdoor axe Roslavl VII with curved handle.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Отзывов: 1

Sharpening stone PETROGRAD, 200*70*20mm, 360 grit

Abrasive water stones. Grit: 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

Отзывов: 1

Spoon Gouge Rubankov, N5, 10mm

Резчицкая стамеска Rubankov клюкарза N5, 10мм. Резчицкая стамеска предназначена для резьбы по дереву. Клюкарза используется для выполнения глубокой барельефной резьбы. Также удачно подходит для выборки углублений при резьбе посуды, кукс, ложек и декорировании деревянной поверхности. 
Эта модель НЕ ЯВЛЯЕТСЯ УДАРНОЙ, ей не работают в паре с киянкой.

Изготовлена на фабрике столярных и плотницких инструментов "ПЕТРОГРАДЪ". Россия

Отзывов: 1

Marking knife PETROGRAD, model N5, arrow form

Marking knives  PETROGRAD have a swept blade that is sharpened on 2 faces, which makes it comfortable to use both right-handed and left-handed. One-sided sharpening. The 2.3mm thick blade is made of high carbon steel and hardened to 58-61HRC. The handle is made of curly maple and saturated with linseed oil. Before the blade on the handle made a comfortable stop to prevent sliding of the hand. The length of the handle is 170mm.Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia

Отзывов: 1

Edge guard for carpenter's chisel 60mm

Carpenter's chisel cover 60mm wide. Leather covers for chisels Petrograd. Designed to protect the cutting edge from damage and cuts during transportation. Assembled with steel rivets and stitched with thread.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia.
Отзывов: 1

Straight Gouge Rubankov, N3, 16mm

Straight Gouge Rubankov, N3, 16mm (0.63 inches)

Carving chisel "Rubankov" Straight Gouge N7, 16mm (0.63 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 16mm ( 0.63inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

Отзывов: 1