Share / Save Link:
Description
Picture framing hammer or glazier's hammer is a hammer with rotating head for strike nails in frame of picture. Because of its 360 degree rotating triangle head it can be easily position on back of a picture frame and precise strike on nail by slide over surface.
- hammer weight 180 grams
- steel rotating triangle head
- steel round head
- full head lenght 70mm
- round head diameter 15mm
- triangle head diameter 22mm
A well-conceived tool for smoothly driving in wire nails when fixing glass panels or backing boards of picture frames. The triangular hammer head has three flat surfaces, which allow you to safely slide the hammer along the glass panle or backing board. The head also rotates, which means you can hold the handle freely even with deep profile grooves. The round hammer head can be used to adjust nails or to drive staples into the frame mitre.
Frame hammers are produced by Petrograd toolworks in Saint Petersburg Russia
| Round Head diametr: | 15 mm |
|---|---|
| Triangle Head diametr: | 22 mm |
| Head lengh: | 70 mm |
| Head material: | steel |
| Shape: | round & triangle |
| Handle lenght: | 315 mm |
| Weight: | 0,18 kg |
*The company reserves the right to change the appearance of the product without further notice, if this does not affect the performance of the tool!
Share / Save Link:
Видеоматериалы
Specs
Reviews
Instructions ()
Publications
Popular goods
Carving knife PETROGRAD, Finnish type, 200mm/60mm
Carving knife PETROGRAD, skew type, 30 degrees
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ. Ножи-косяки с углом скоса 30, 40 градусов двухсторонняя заточка. Длина лезвия - 40 мм, ширина 13 мм, прямой обух. Удобная овальная рукоять из красного дерева пропитана маслом и покрыта шеллаком. Длина рукояти - 140 мм. Нож для широкого спектра работ. Лезвие толщиной 2,5 мм выполнено из стали 65Г с закалкой до твердости 59-61 HRc. Заточен и готов к работе.
Сделано в России
Adze PETROGRAD, type n3, Svedish style, half round, external bevel
Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia
Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Cutting knife PETROGRAD, double bevel 30 deg, 20mm/167mm
Knives jambs with a bevel angle of 30 degrees.
The blade length is shown in the table, the blade thickness is about 2 mm. The blade is made of 65G (Germany 66Mn4, Ck67, USA 1066) steel hardened of 59-61 HRc. Convenient rectangular handle of sapele soaked with oil. Sharpened and ready to go. Knives with a slanting sharpening have a wide range of applications (carving, marking, working with cardboard, marquetry, intarsia, veneering, working with leather, producing musical instruments, modeling and in everyday life).
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| item code | sharpening, deg | width, mm | length, mm | thickness, mm |
| М00013992 | left-sided | 20 | 180 | 2 |
| М00013991 | right-sided | 20 | 180 | 2 |
| М00013993 | double-sided | 20 | 180 | 2 |
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Bit for checkering tool N2-16, 90°
Насадка на резец для чекеринга N2-16, 90° (две РК). Обе стороны с зубчиками. Используется для нанесения канавок и их углубления после нанесения. Одно лезвие проходит вдоль направляющей линии, в то время как другое намечает следующую канавку. При переходе на следующую канавку инструмент углубляет ее и снова наносит следующую канавку. Резец 2 Представляет из себя комбинацию инструментов для расширения и углубления канавок. Обе вершинки являются резцами.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Outdoor axe PETROGRAD, model Roslavl V, curved handle
Small axe Roslavl V (hatchet) with curved handle. Axe has a superior cutting abilities, it's lightweight and short. Would be good choiсe for any outdoor activity like campings, spoon making, making bonfire and etc. This axe is ideal for those who want take a small axe for different ways of use when you are going out and about in the countryside or fishing or hunting.The axe is also excellent for delimbing a tree and making wooden stakes.
- Total lenght is 270 mm ( 10,63 inch )
- Height of axe is 130 mm ( 5,12 inch )
- Lenght of cutting edge is 90 mm ( 3,54 inch )
- Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
- Curved cutting edge was straight sharpened.
- Total weight of axe is 0,5 kg ( ± 0,05kg )
- Handle lenght is 270 mm ( 10,63 inch) and it is made from solid mapple with right grain position.
- The axe comes with leather case for protecting cutting edge.
Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.
Axe Roslavl V produced by Petrograd toolworks in Saint Petersburg Russia.
| Head weight: | 0.34 kg |
|---|---|
| Full weight: | 0.5 kg |
| Type: | outdoor hatchet |
| Steel: | 65Г |
| Hardness: | 55-58HRc |
| Handle material: | Maple* |
| Handle lenght: | 270 mm |
| Edge: | Curved |
| Sharpening angle: | 30 degrees |
| Blade lenght: | 90 mm |
| Total lenght: | 270 mm |
** coating oil may changes too
Chisel handle n18
Рукоять для стамесок n17. Ручка имеет восьмигранную эргономичную форму. Не шлифована, ничем не покрыта, с кольцом. Латунное кольцо придает изысканный вид и предотвращает рукоять от растрескивания. Рукоять изготовлена из ценных пород древесины. Ударная сторона закруглена, чтобы не наминать мозоли на ладонях. В рукояти имеется отверстие для хвостовика стамески.
Производство фабрики столярных и плотницких инструментов ПЕТРОГРАДЪ
Carving set PETROGRAD n18, 6 tools, chisel handles
Набор мини стамесок для резьбы по дереву, ПЕТРОГРАДЪ, N18, 6 предметов. Авторский набор резцов для миниатюрной резьбы по дереву. Эти прекрасные инструменты подойдут для моделистов, любителей миниатюрной резьбы и для максимальной деталировки резьбы. Набор включает четыре полукруглые стамески, одну плоскую стамеску и уголок. Производство Россия.
Chisel & file handle n26
Рукоять для стамесок и напильников n26, 132мм – это великолепная и продуманная ручка. Она может быть применима к стамескам, рашпилям, напильникам. Материал – массив ясеня высшего сорта. Рукоять обладает латунным кольцом. Производство фабрика Петроградъ (Россия).