Share / Save Link:
Center Steady, PETROGRAD, Model N2, D320mm
Description
Designed for machines with a center height of 160mm.
Billets with a diameter of no more than 200mm and no less than 15mm.
Made of 52mm plywood.
Designed for 11mm bed.
The distance between the guides of the bed is 49mm.
Has three points of support for the workpiece.
The wheels are soft and leave no marks on the workpiece.
The wheel bearings are dustproof.
Also, the rods have a symmetrical design and have the ability to roll inward with rollers.
The fixing of the rods, as well as the base of the steady rest, is done manually.
Conversion to a different diameter takes just a few seconds.
The lunette was developed by the head of production of the Petrograd company and the teacher of the Rubankov school, Dmitry Nikolayevich Pushin.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia
Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
The book `Practical course of woodturning art` + Atlas of drawings, M. Netyksa
The book is about woodturning art as a separate craft that includes not only the work on the lathe. This book was a basic textbook on turning wood and bone throughout the first half of the twentieth century. Moscow 1910 / Reprint edition of St. Petersburg 2017. Format 145x215 mm, hard tissue binding, 440 pages. Also included is an album of drawings attached to the 1910 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.
Table of contents.
Division I. Machines, equipment and tools
Division II. Work techniques and special devices
Division III. Various materials in turning
Division IV. Adhesives, putties and surface grinding
Division V. Decoration and Surface Finishing Turning Works
Lathe's tool rest PETROGRAD, S-type, arrm 330mm*D20mm, bar D15.8mm*105mm
Подручник для токарного станка S-образный, ПЕТРОГРАДЪ, 330мм удобен для точения чаш и тарелок. Материал - сталь. Диаметр стержня 15,8 мм. Идеально подходит для токарного станка имеющим диаметр стержня подручника 15,8.
Изготовлен на фабрике столярных и плотницких инструментов ПЕТРОГРАДЪ.
Производство (Россия)
Cup Chuck D35mm for Woodturning Lathe M20х1.5mm, PETROGRAD
Chuck diameter 35mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М20х1.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.
Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)
Popular goods
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-18, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Leather Knife PETROGRAD, type 1, single stright bevel
Straight and flat leather Knife type 1 with a single bevel (up or right). This model has one flat side and one bevel side. It's simple knife for paring and skiving.
- for straight cuts
- for skiving
- for paring
Flat Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and ready to work out of the box.
This type of knives is used in handicraft, leather work, and shoemaking.
- blade made of tool alloy steel 9ХФ
- blade thickness - 1.7 mm
- edge lenght - 40 mm
- blade lenght - 70mm
- handle made of wood *
- oil covered **
Straight Gouge Rubankov, N3, 6mm
Straight Gouge Rubankov, N3, 6mm
Straight Gouge Rubankov, N3, 6mm (0.43 inches)
Carving chisel "Rubankov" Straight Gouge N3, 6mm (0.43 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 6mm ( 0.43 inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.
Gouge is sharpened, honed and fully ready to work out of the box.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )
Straight Gouge Rubankov, N2, 14mm, fishtail
RUBANKOV chisels are forged from low-alloy high-carbon steel. Hardened to a hardness of 59-61 HRc.
The faceted handle is made of precious wood and covered with oil. The impact side is rounded so as not to crush calluses on the palms. The brass ring has an exquisite look and the effect of the handle from cracking when working with a mallet. The internal profile of the chisel is polished, the detected edge is sharpened and ready for work.
These models are percussion, they can be paired with a mallet.
The declared geometric dimensions vary in handling, as the tool is made and hoarded by hand.
The length of the metal sheet is 145 mm. Overall length with handle 280mm.
Web width - 14mm.
Made at the PETROGRAD joinery and carpentry tools factory.
Production Russia.
Straight Carving Chisel Rubankov, N1, 10mm
Straight carving gouge N1 has 10mm wide blade(0.39 inches) and slight profile for better carving abilities. It is universal wood carving chisel that perfectly suits for carving hard or soft wood. Best choice for relief wood carving.
- cutting edge width - 10mm (0.39 inches)
- blade lenght is 145mm (5.71inches)
- Made of alloy steel
- hand forged
- hardened to 59-61HRc
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )
Carving set PETROGRAD n19, 6 tools, chisel handles
Набор мини стамесок для резьбы по дереву, ПЕТРОГРАДЪ, N19, 6 предметов. Авторский набор мини-стамесок для миниатюрной резьбы по дереву. Эти прекрасные инструменты подойдут для моделистов, любителей миниатюрной резьбы и для максимальной деталировки резьбы. Набор включает три плоские прямые стамески, две косые стамески и одну полукруглую стамеску. Производство Россия.
Petrograd Bushcraft Straight Gouge, n7, 30mm
Прямая стамеска для вырезания ложки, профиль Н7, ширина 30 мм. Эта стамеска была специально разработана с оглядкой на нужды ложкарей, ее профиль и общие габариты, даже внешний вид, подобраны исходя из эргономики изготовления деревянной ложки. Прямые стамески подходит для множества задач от создания фигурных форм до подбора фона Стамеска подойдет и для классической резьбы при съеме материала. Производство фабрика Петроградъ (Россия)