Share / Save Link:
Center Steady, PETROGRAD, Model N2, D460mm
Description
Designed for machines with a center height of 230mm.
Billets with a diameter of not more than 340mm and not less than 15mm.
Made of 52mm plywood.
Designed for 11mm bed.
The distance between the guides of the bed is 63mm.
Has three points of support for the workpiece.
The wheels are soft and leave no marks on the workpiece.
The wheel bearings are dustproof.
Also, the rods have a symmetrical design and have the ability to roll inward with rollers.
The fixing of the rods, as well as the base of the steady rest, is done manually.
Conversion to a different diameter takes just a few seconds.
The lunette was developed by the head of production of the Petrograd company and the teacher of the Rubankov school, Dmitry Nikolayevich Pushin.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia
Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
The book `Practical course of woodturning art` + Atlas of drawings, M. Netyksa
The book is about woodturning art as a separate craft that includes not only the work on the lathe. This book was a basic textbook on turning wood and bone throughout the first half of the twentieth century. Moscow 1910 / Reprint edition of St. Petersburg 2017. Format 145x215 mm, hard tissue binding, 440 pages. Also included is an album of drawings attached to the 1910 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.
Table of contents.
Division I. Machines, equipment and tools
Division II. Work techniques and special devices
Division III. Various materials in turning
Division IV. Adhesives, putties and surface grinding
Division V. Decoration and Surface Finishing Turning Works
Lathe's tool rest PETROGRAD, S-type, arrm 330mm*D20mm, bar D15.8mm*105mm
Подручник для токарного станка S-образный, ПЕТРОГРАДЪ, 330мм удобен для точения чаш и тарелок. Материал - сталь. Диаметр стержня 15,8 мм. Идеально подходит для токарного станка имеющим диаметр стержня подручника 15,8.
Изготовлен на фабрике столярных и плотницких инструментов ПЕТРОГРАДЪ.
Производство (Россия)
Cup Chuck D35mm for Woodturning Lathe M20х1.5mm, PETROGRAD
Chuck diameter 35mm. Steel unhardened chuck for turning centers. A simple and reasonably safe chuck compared to a jaw chuck. Simple and reliable and compact. Allows you to work in close proximity to it. Thread М20х1.5mm. Parts are easily and securely fastened in the chuck, as the chuck has a small inner cone. It is also possible to work without a back center.
Made at the PETROGRAD joinery and carpentry tools factory.
Production (Russia)
Popular goods
Carving knife PETROGRAD, Finnish type, 200mm/60mm
Carving knife PETROGRAD, skew type, 30 degrees
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ. Ножи-косяки с углом скоса 30, 40 градусов двухсторонняя заточка. Длина лезвия - 40 мм, ширина 13 мм, прямой обух. Удобная овальная рукоять из красного дерева пропитана маслом и покрыта шеллаком. Длина рукояти - 140 мм. Нож для широкого спектра работ. Лезвие толщиной 2,5 мм выполнено из стали 65Г с закалкой до твердости 59-61 HRc. Заточен и готов к работе.
Сделано в России
Adze PETROGRAD, type n3, Svedish style, half round, external bevel
Adze N3 was created on the basis of samples of adzes from Sweden and Norway, whose house-building traditions have the same deep roots as in Russia
Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 75 mm. Overall length - 650 mm. Weight - 1.6 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Cutting knife PETROGRAD, double bevel 30 deg, 20mm/167mm
Knives jambs with a bevel angle of 30 degrees.
The blade length is shown in the table, the blade thickness is about 2 mm. The blade is made of 65G (Germany 66Mn4, Ck67, USA 1066) steel hardened of 59-61 HRc. Convenient rectangular handle of sapele soaked with oil. Sharpened and ready to go. Knives with a slanting sharpening have a wide range of applications (carving, marking, working with cardboard, marquetry, intarsia, veneering, working with leather, producing musical instruments, modeling and in everyday life).
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| item code | sharpening, deg | width, mm | length, mm | thickness, mm |
| М00013992 | left-sided | 20 | 180 | 2 |
| М00013991 | right-sided | 20 | 180 | 2 |
| М00013993 | double-sided | 20 | 180 | 2 |
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Bit for checkering tool N2-16, 90°
Насадка на резец для чекеринга N2-16, 90° (две РК). Обе стороны с зубчиками. Используется для нанесения канавок и их углубления после нанесения. Одно лезвие проходит вдоль направляющей линии, в то время как другое намечает следующую канавку. При переходе на следующую канавку инструмент углубляет ее и снова наносит следующую канавку. Резец 2 Представляет из себя комбинацию инструментов для расширения и углубления канавок. Обе вершинки являются резцами.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Outdoor axe PETROGRAD, model Roslavl V, curved handle
Small axe Roslavl V (hatchet) with curved handle. Axe has a superior cutting abilities, it's lightweight and short. Would be good choiсe for any outdoor activity like campings, spoon making, making bonfire and etc. This axe is ideal for those who want take a small axe for different ways of use when you are going out and about in the countryside or fishing or hunting.The axe is also excellent for delimbing a tree and making wooden stakes.
- Total lenght is 270 mm ( 10,63 inch )
- Height of axe is 130 mm ( 5,12 inch )
- Lenght of cutting edge is 90 mm ( 3,54 inch )
- Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
- Curved cutting edge was straight sharpened.
- Total weight of axe is 0,5 kg ( ± 0,05kg )
- Handle lenght is 270 mm ( 10,63 inch) and it is made from solid mapple with right grain position.
- The axe comes with leather case for protecting cutting edge.
Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.
Axe Roslavl V produced by Petrograd toolworks in Saint Petersburg Russia.
| Head weight: | 0.34 kg |
|---|---|
| Full weight: | 0.5 kg |
| Type: | outdoor hatchet |
| Steel: | 65Г |
| Hardness: | 55-58HRc |
| Handle material: | Maple* |
| Handle lenght: | 270 mm |
| Edge: | Curved |
| Sharpening angle: | 30 degrees |
| Blade lenght: | 90 mm |
| Total lenght: | 270 mm |
** coating oil may changes too
Chisel handle n18
Рукоять для стамесок n17. Ручка имеет восьмигранную эргономичную форму. Не шлифована, ничем не покрыта, с кольцом. Латунное кольцо придает изысканный вид и предотвращает рукоять от растрескивания. Рукоять изготовлена из ценных пород древесины. Ударная сторона закруглена, чтобы не наминать мозоли на ладонях. В рукояти имеется отверстие для хвостовика стамески.
Производство фабрики столярных и плотницких инструментов ПЕТРОГРАДЪ
Carving set PETROGRAD n18, 6 tools, chisel handles
Набор мини стамесок для резьбы по дереву, ПЕТРОГРАДЪ, N18, 6 предметов. Авторский набор резцов для миниатюрной резьбы по дереву. Эти прекрасные инструменты подойдут для моделистов, любителей миниатюрной резьбы и для максимальной деталировки резьбы. Набор включает четыре полукруглые стамески, одну плоскую стамеску и уголок. Производство Россия.
Chisel & file handle n26
Рукоять для стамесок и напильников n26, 132мм – это великолепная и продуманная ручка. Она может быть применима к стамескам, рашпилям, напильникам. Материал – массив ясеня высшего сорта. Рукоять обладает латунным кольцом. Производство фабрика Петроградъ (Россия).