PETROGRAD Workbench's hardware kit N1



Rating : (1)
Shipping: worldwide

9740 p (149.8) out of stock

Description

Joinery vice, model Moxon, capture width - 380mm. Dovetail vise, Moxon vise.
A special version of the vice with two screws for convenient work with the edges and ends of the panels. Overall dimensions: 580x145x120. The thickness of the jaws is 45mm.
Maximum width of the workpiece to be clamped (distance between screws) 380mm.
Maximum workpiece thickness (screw travel) - 30mm
The vise was designed by Sergey Aleksandrovich Klein based on the early work of Anry Ruobo and Joseph Moxon.
We did not strive to make an exact copy of the vice, we set ourselves the task of making a functional and affordable tool for comfort when working with a dovetail joint. This vice does not replace the classic workbench, but is a device that expands the arsenal of any craftsman.
We reserve the right to make minor design changes to improve vise performance.

Finishing oil PETROGRAD for workbenches and tool handles, 0.5l. Primer, used to apply the first coat before finishing. Recommended for use on hard or absorbent wood. Recommended for workbenches, tables, handles, woodworking tools and other woodworking parts. For indoor use only. It quickly and deeply penetrates the material and also quickly polymerizes.
Composition:
Tung oil, linseed oil, modified oils (linseed, tung, safflower, walnut), ricin oil, carnauba wax, micronized wax.
Mode of application:
Apply oil evenly to the prepared surface free of dirt and grease using a brush or lint-free cloth. After 10 minutes, wipe off the remaining oil from the surface with a dry, lint-free cloth. After 8 hours (depending on layer thickness and ambient temperature) apply a second coat. Ensure good ventilation of the room, both during application and at the end of work.
Note:
Certain oily, exotic or brightly colored woods and excessive amounts can prevent the oil from drying or greatly slow down the drying process. In this case, good ventilation is needed to speed it up.
- Do not use nitrile gloves for work.
- Safe for hands
- Always wear protective goggles when working.
Storage:
In a sealed container. It should be kept away from sources of fire and sparks.


These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

%

Magazine Master&Workshop 2020 № 2 (9)

Журнал Мастер и мастерская 2020 2 (9)

500p(149.8)
Отзывов: 1
>Рейтинг:

Strop PETROGRAD, for carving tools, 150mm*30mm

The bar with glued leather is designed for finishing semi-circular chisels, drawknives, etc. One of the flat sides can also be used for fine-tuning of flat tools. The size of the bar is 150x30 mm. Min radius - 3 mm, max. radius -6 mm. It can be used with polishing pastes. Material - ash, leather - reversal 2mm. Leather color may differ from the image on the site. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv)

Carpenter drawknife PETROGRAD N7, for cleaning up grooves in logs (Meddragskniv). A complete analogue of the Norwegian drawknife Meddragskniv. The thickness of the blade is 6 mm, the radius of the groove is 35 mm, the distance between the handles is 400 mm, the angle of grinding is 30 degrees. Forged, hardened 65G steel (Germany 66Mn4, Ck67, USA 1066) blade, cutting edge hardness - 55-58HRC. Total weight ~ 1.1kg. Handle length - 140mm. Handles are made of beech.
Designed for finishing the lunar groove after adze (removes the effect of scaly). The shape of the shoulder allows you to rotate it when working to grind the entire surface of the groove. Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.

12300p
Отзывов: 1
Рейтинг:

Sash Framing Chisel, PETROGRAD, model Istra, 38mm

Forged carpentry chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.

Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.

8700p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 20mm

Стамеска ПЕТРОГРАДЪ, серия Волга, 20 мм. Производятся шириной от 3мм до 50мм. Кованые стамески Волга спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков.
Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при доработке шиповых соединений и соединений на ласточкин хвост. Толщина лезвия переменная и увеличивается от РК к рукояти.
Полотно из инструментальной высоколегированной стали, закалено до 61HRc. Спинка столярной стамески или рабочая сторона выровнена на плоскошлифовальных станках. Стамески Волга производства фабрики Петроградъ заточены и готовы к работе. Заводской угол заточки 25град.
Деревянная рукоять выполнена из твердых пород древесины, усилена латунным кольцом для силовой работы с киянкой.
3100p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 32mm

Стамеска ПЕТРОГРАДЪ, серия Волга, 32мм. Производятся шириной от 3мм до 50мм. Кованые стамески Волга спроектированы, ориентируясь на многолетний опыт мастеров-краснодеревщиков.
Форма лезвия имеет боковые скосы для работы в труднодоступных местах, например при доработке шиповых соединений и соединений на ласточкин хвост. Толщина лезвия переменная и увеличивается от РК к рукояти.
Полотно из инструментальной высоколегированной стали, закалено до 61HRc. Спинка столярной стамески или рабочая сторона выровнена на плоскошлифовальных станках. Стамески Волга производства фабрики Петроградъ заточены и готовы к работе. Заводской угол заточки 25град.
Деревянная рукоять выполнена из твердых пород древесины, усилена латунным кольцом для силовой работы с киянкой.
3400p
Отзывов: 1
Рейтинг:
new

Forest axe PETROGRAD, model Bryansk

Large forged felling ax Bryansk. This large ax is perfect for felling and chopping trees. 
It will also not be superfluous on the farm, because with its help you can chop small logs and trim something.
Due to the lenticular sharpening, the cutting edge has increased wear resistance.
11000p
Отзывов: 1
Рейтинг:
new

Spoon knife, PETROGRAD, type 1/22, left-handed

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3000p
Отзывов: 1
Рейтинг:
new

Книга "Резьба деревянной ложки своими руками", Игорь Васильева

Книга "Резьба деревянной ложки своими руками", Игорь Васильева посвящена процессу создания деревянной ложки. Начиная от подготовительных работ и заканчивая финишным покрытием.

850p
Отзывов: 1
Рейтинг:
new

Carving knife PETROGRAD, skew type, 60 degrees

Ножи-косяки резчицкие с углом скоса 30, 40, 60 градусов, двухсторонняя заточка. Толщина клинка - около 2мм. Удобная рукоять из дерева, пропитаного маслом. Длина рукояти 140 мм. Нож для широкого спектра работ. Производство фабрика Петроградъ (Россия).

2400p
Отзывов: 1
Рейтинг: