Categories
Lathe's tool rest PETROGRAD, J-type, arrm 180mm, bar D15.8mm*105mm
- Основной склад: 7 шт.Петербург: 1 шт.Москва: 1 шт.
Description
Подручники для токарного станка J-образные, ПЕТРОГРАДЪ, длиной 220мм удобен для точения чаш и тарелок. Материал - сталь. Диаметр стержня 15,8 мм. Идеально подходит для токарных различных моделей со стержнем 15,8 мм.
Изготовлен на фабрике столярных и плотницких инструментов ПЕТРОГРАДЪ.
Производство (Россия)
Are you sure?
Find out a mismatch? Highlight text and press Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Popular goods
Carving knife PETROGRAD, skew type, 30 degrees
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ. Ножи-косяки с углом скоса 30, 40 градусов двухсторонняя заточка. Длина лезвия - 40 мм, ширина 13 мм, прямой обух. Удобная овальная рукоять из красного дерева пропитана маслом и покрыта шеллаком. Длина рукояти - 140 мм. Нож для широкого спектра работ. Лезвие толщиной 2,5 мм выполнено из стали 65Г с закалкой до твердости 59-61 HRc. Заточен и готов к работе.
Сделано в России
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-18, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N2-22, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-18, 90°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N4-18, 90°
Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering gauge
Checkering gauge for markup. Allows you to accurately measure the number of checkering lines on ready products, and mark a new pattern on blanks for checkering.
- measures the number of lines
- measures the shape and angle of diamonds
The corners of the template allow you to measure the shape and size of the diamond in the pattern (checkers ratio).
- edges of the diamond 3 to 1
- edges of the diamond 3.5 to 1
The edges of the template are engraved with the number of checker lines per inch.
- 16, 18, 20, 22 lines per inch (side 1)
- 24, 26, 28, 32 lines per inch (side 2)
Checkering template is an indispensable assistant for work. The gauge is made of hard plastic with engraving and color spraying.
Production of the Petrograd toolworks.
| Lines measurement: | 8 sizes |
|---|---|
| Checkers ratio: | 2 |
| Material: | Hard plastic |
| Lenght: | 235 mm |
| Width: | 70 mm |
| Weight: | 0.012 kg |
Sharpening stone PETROGRAD, 200*70*20mm, 120 grit
Abrasive water stones. Grit: 120, 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 2000 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.