Categories
Carving knife PETROGRAD, Axe type, 32mm / 60 degree
- Петербург: 1 шт.Москва: 2 шт.
Description
Резец-топорик для резьбы по дереву, ПЕТРОГРАДЪ, 32 мм / 60 градусов является частью новой линейки ножей для резьба по дереву Петроградъ. Этот нож основан на резцах-топориках мастера-резчика Адольфа Юрьева. Производство фабрика Петроградъ (Россия).
Характеристики резца:
- Сталь: 65Г
- Закалка: 60-61 HRC
- Рукоять: ясень
- Длина РК: 32 мм
- Угол скоса: 60 градусов
- Угол заточки: 20 градусов
Обновлённый модельный ряд знаменитых ножей-топориков, предназначенных для геометрической резьбы.В отличие от предыдущих моделей, резцы получили более удобную рукоять и защитное кольцо, предохраняющее рукоять от сколов при увеличении нагрузки на клинок при работе с твёрдыми породами древесины.
Разработаны конструктором фабрики ПЕТРОГРАДЪ Александром Сергеевичем Савиным в начале 2023 года, первая партия резцов выпущена фабрикой в августе 2023 года.При конструировании резцов использовались идеи замечательного резчика по дереву Адольфа Юрьева, использующего резцы подобного типа для своих работ.
Are you sure?
Find out a mismatch? Highlight text and press Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
PETROGRAD small carving dowetail chisel 23mm, double bevel
Резец-топорик для резьбы по дереву, ПЕТРОГРАДЪ, 23 мм / 90 градусов, торцевой является частью новой линейки ножей для резьба по дереву Петроградъ. Этот нож основан на резцах-топориках мастера-резчика Адольфа Юрьева. Производство фабрика Петроградъ (Россия).
PETROGRAD carving knife , skew type, 5mm / 60 degree
Резец-топорик для резьбы по дереву, ПЕТРОГРАДЪ, 6 мм / 60 градусов является частью новой линейки ножей для резьба по дереву Петроградъ. Этот нож основан на резцах-топориках мастера-резчика Адольфа Юрьева. Производство фабрика Петроградъ (Россия).
Popular goods
Carving knife PETROGRAD, Finnish type, 200mm/60mm
Carving knife PETROGRAD, skew type, 40 degrees
Carving knives with a bevel angle of 30, 37, 40 degrees double-sided sharpening. Blade length - 40 mm, width 13 mm, straight butt. A comfortable maple oval handle is saturated with oil and covered with shellac. The length of the handle - 115 mm. Knife for a wide range of works:
- marquetry, intarsia, veneering
- leather crafts
- production of musical instruments
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Model | Code | Handle | Blade lenght | Blade width | Scew angle | Total lenght |
| Carving knife PETROGRAD, skew 30 deg, 155mm/40mm | M00013393 | maple | 35 | 23 | 30 | 145 |
| Carving knife PETROGRAD, skew 37 deg, 140mm/40mm | M00013990 | maple | 35 | 35 | 37 | 160 |
| Carving knife PETROGRAD, skew 40 deg, 145mm/40mm | M00014065 | sapele | 30 | 20 | 40 | 165 |
Carving axe PETROGRAD, model Zvenigorod 7, handle n5
Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.
- Blade width 120 mm
- Sharpening angle - 25 degrees
- Hardness - 55-58HRc
- Handle lenght - 350 mm
- Full weight - 07 kg
Carving axe Zvenigorod VII is quite small and easy to control. It's weight is about 650g, makes it maneuverable and allows you to work more accurate and precise.
The shape of the axe head was designed for carving operations where palm is resting extreamly close to axe head or even on the axe head. This design helps to exelent control of the axe even during long carving sessions. Grip above the head is used for trimming, stripping. This axe model was based on samples from museum "Rubankov" and finalized taking into account the wishes of wood carvers.
The axe head is hand forged from steel 65Г (spring steel) and hardened to 55 - 58 HRc at the cutting edge and along the entire beard, the rest part is normalized to HB280. This hardening allows you to hit the poll without the risk of creating a cracks in the metal.
Head has mounted to handle on 3 wedges, one along the head eye and two in cross section.
Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.
Axe handle is made of maple* and coated with Danish oil**. The hatchet handle has a longitudinal bend. In cross-section the handle has the shape of an egg, which is very convenient for good grip while carving. Handle has a hole for hanging.
Woodcarving axe Zvenigorod VII are product of Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.
Picture framing glazier's hammer, PETROGRAD, model N2
Picture framing hammer or glazier's hammer is a hammer with rotating head for strike nails in frame of picture. Because of its 360 degree rotating triangle head it can be easily position on back of a picture frame and precise strike on nail by slide over surface.
- hammer weight 180 grams
- steel rotating triangle head
- steel round head
- full head lenght 70mm
- round head diameter 15mm
- triangle head diameter 22mm
A well-conceived tool for smoothly driving in wire nails when fixing glass panels or backing boards of picture frames. The triangular hammer head has three flat surfaces, which allow you to safely slide the hammer along the glass panle or backing board. The head also rotates, which means you can hold the handle freely even with deep profile grooves. The round hammer head can be used to adjust nails or to drive staples into the frame mitre.
Frame hammers are produced by Petrograd toolworks in Saint Petersburg Russia
| Round Head diametr: | 15 mm |
|---|---|
| Triangle Head diametr: | 22 mm |
| Head lengh: | 70 mm |
| Head material: | steel |
| Shape: | round & triangle |
| Handle lenght: | 315 mm |
| Weight: | 0,18 kg |
*The company reserves the right to change the appearance of the product without further notice, if this does not affect the performance of the tool!
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-16, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter №2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N2-20, 60°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-16, 90°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.