Categories
Description
The beveled chamfer of the cutting edge makes this small ax quite aggressive. This forged ax will cope even with the felling of small trees. The huntsman is a hiking ax, a garden ax, a chisel ax, a hunting ax, a tourist ax, a carpenter's ax, and even a chisel ax. Recommended for bushcraft lovers and survivalists!
Steel ШХ15, with zone hardening of the blade, cutting edge hardness about 58 HRC. Has an impact butt and can be used instead of a hammer.
The handle is made of ash and covered with oil.
It is completed with a leather case with a holster clasp. Reliably protects the cutting edge.
Total length 450 mm.
The ax weighs only 1100 grams.
The manufacturer has the right, without prior notice, to make changes to the product that do not impair its technical characteristics, but are the result of work to improve its design or production technology.
Are you sure?
Find out a mismatch? Highlight text and press Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
Magazine Master&Workshop 2021 № 1 (11)
This is a periodical magazine about woodworking, craftsmen and workshops, about the news of the carpentry world. The best masters share their knowledge and experience with everyone. Illustrated specialized full-color magazine.
Diamond sharpening stone PETROGRAD 200mm*70mm 2000 grit
Diamond sharpening stones PETROGRAD bars are intended for processing high-carbon steels and cast iron products. Diamond bars are monolithic sharpening with a continuous flat diamond layer. The diamond-bearing layer of the bars is made of synthetic diamond micropowders on a copper-tin bond M2-01.
The relative concentration of highly aggressive synthetic diamonds (ASD) is 100%.
Aggressive diamonds provide high productivity. Also, the bars have high abrasion resistance.
Diamond stones do not need to be soaked in water prior to use as they do with abrasive stones, but should be handled with honing oil or water.
Diamond bars are monolithic six-sided, therefore 6 sides are working.
Size, mm - 200x70x3 - LxWxH.
The following grains are available: 7/5 (2000грит)
Textile Tool Roll, PETROGRAD, type 3, 8 pockets, 750mm*950mm
Сумки-скрутки инструментальная тканевые.
Размер - 750х950мм, 8 карманов.
Предназначена для хранения инструментов: резцов, стамесок, ножей. Максимальная длина инструмента - 900мм. Выполнена из брезентовой ткани - 100 % хлопок, прошитые швы.
цвет сумок может отличаться от того, что на картинке.
Инструмент в комплект не входит
Во избежание выскальзывания инструментов из сумки рекомендуем укладывать стамески в карманы сумки рукоятями внутрь. Также рекомендуем укладывать стамески в сумку с надетыми на режущие кромки защитными колпачками.
Производство - Россия.
Производитель оставляет за собой право вносить в конструкцию сумки изменения, не приводящие к ухудшению её качеств.
Shallow Hook Knife, PETROGRAD, type 3, left-handed
Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.
- Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
- All hook cutters are sharpened and ready to go.
- The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
- The handle of the hook knife is made of maple and coated with oil*.
The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.
| Blade width: | 12 mm |
|---|---|
| Blade lenght: | 75 mm |
| Steel: | 9ХС |
| Shape: | hook |
| Handle grip: | left-handed |
| Handle lenght: | 160 mm |
| Total lenght: | 235 mm |
| Weight: | 0,1 kg |
Popular goods
Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete N2-18, 60°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-18, 60°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 60°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving set PETROGRAD, N5
The set N5 includes:
- Carving knife PETROGRAD, Swedish type, 175mm/60mm
- Carving knife PETROGRAD, skew 40 deg, 165mm/35mm
- Spoon knife ( hook knife ) model N1, D 27mm, right one
- Sharpening stone PETROGRAD, 120*15*15mm, 1500 grit
- Textile 4 pocket Tool Roll, PETROGRAD, 360*200mm
Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit
Water stone. 2000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
Comparison of FEPA, JIS and GOST standards:
Apron RUBANKOV, model 4, light-brown
Фартук Столярный Rubankov кожаный, светло-коричневый. Длина фартука - 800 мм, ширина - 680 мм. Нагрудный карман c 1 отделением. Размеры нагрудного кармана - длина 150 мм, ширина 175 мм. Лямки и поясной ремень оборудованы застежками и пряжками. Цвет фартука - светло-коричневый. На фартук нанесен логотип Rubankov. Материал - 100 % натуральная кожа, металлическая фурнитура.
Сделано в России.