Share / Save Link:

PETROGRAD Glue Press 100cm*10cm



Rating :
(1)
Shipping: worldwide

9500 p (146.11)

Description

It is used for gluing wooden boards and plots up to 100mm thick. The pressure block made of high-strength steel ensures high uniform pressure on the lamellas. The minimum and maximum thickness of the glued board varies from 25mm to 100mm.

Thanks to the special design of the clamp, uniform pressure is exerted on the workpieces to be glued from 4 sides. This ensures a strong gluing without gaps, provided that the plots are properly planed and glue is of good quality.

Two removable stop pins with a removable pin allow you to quickly rearrange the backgauge to adjust the required dimensions.

Trapezoidal screw length - 250, diameter - 23mm, thread pitch 3mm. (Attention. During operation, the screw must be cleaned of sawdust and lubricated with any machine oil. This will significantly increase the service life of the tool). The guides are made of a rectangular profile 60x30mm and have a wall thickness of 2mm. The clamps are painted with impact-resistant paint.


Made in Russia

Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

new

Magazine Master&Workshop 2021 № 1 (11)

This is a periodical magazine about woodworking, craftsmen and workshops, about the news of the carpentry world. The best masters share their knowledge and experience with everyone. Illustrated specialized full-color magazine.

800p(146.11)
Отзывов: 1
>Рейтинг:

Wooden fore plane PETROGRAD, 455mm/60mm

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil. The wedge is also made of maple. The installation angle of the knife is 50 ° -55 °. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 60 mm, knife thickness minimum 2.2 mm, maximum thickness - 3.5 mm. Sharpening angle 30 °. Dimensions of jointer plane 455 * 80 * 170 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

14000p(146.11)
Отзывов: 1
>Рейтинг:
new

Petrograd Brass Square 85mm, one-side marking

Elbow flat PETROGRAD, 85mm * 50mm. The square is one of the most used measuring tools in joinery. Ruler width 20 mm. Metric markings in 1 mm increments on the outside and inside. The error of the square is 0.05mm per 100mm. Used not only for checking 90 degree angles and marking, but also for setting up tools, saws and other tools. Material - brass. Engraved etched markings for easy reading.

Production of the PETROGRAD factory.

900p(146.11)
Отзывов: 1
>Рейтинг:
new

Wheel marking gauge Petrograd, type 1

Рейсмус разметочный, диапазон разметки 0 - 150мм. Предназначен для разметки шиповых соединений, фальцев, гнезд, используется при установке петель, при разметке параллельных деталей перед их фуговкой.

3560p(146.11)
Отзывов: 1
>Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 190mm/60mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1400p
Отзывов: 1
Рейтинг:

Spoon knife, PETROGRAD, type 1, D 27mm, left-handed

Spoon knife  (or shallow hook knife) is used to made wooden spoon, as well as for other similar work. Spoon knife blade is cutting out a hollow in a wooden spoon or scoop. Spoon knife N1 has a ring profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

  • Knife blade width - 8 mm.
  • The inner radius of the blade - 15mm.
  • Spoon cutter length - 45 mm
  • Handle length - 130 mm
  • Total length of the spoon knife - 175 mm
  • Spoon knife blade made from tool steel (9ХС; 150Cr14, 90CrSi, 90CrSi5) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the ring has a convex lens-like shape and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

2400p
Отзывов: 1
Рейтинг:

Sharpening set PETROGRAD N4, for knives, 6 stones

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Production - made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

2380p
Отзывов: 1
Рейтинг:

Carving axe PETROGRAD, model Zvenigorod IX

Axe for artistic woodworking and sculpture making. This model was created according to the matrices of the Sweden axe GRANSFORS BRUKS SCULPTOR, building on the models of traditional craft axes. The relatively long, rounded blade with a wide and straight chamfer provides support for wood carving. The cutout on the axe allows you to keep it closer to head for more accurate work. The cutting edge length is 120 mm, the length of the axe is 360 mm. Weight 950 g. The axe is made of excellent steel 65G. The axe undergoes high-quality hardening and forging to a hardness of 58-60 HRc. Forging manually allows you to significantly increase strength. The handle is made of solid maple wood and impregnated with tung oil to prevent rotting. The axe is mounted on the handle with the help of two wooden wedges. Includes a genuine leather case for protecting blade. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia

8500p
Отзывов: 1
Рейтинг:

Carving axe PETROGRAD, model Zvenigorod VII

Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.

  • Blade width 125 mm
  • Head height 145 mm
  • Sharpening angle - 30 degrees
  • Hardness - 55-58HRc
  • Handle lenght - 350 mm
  • Full weight - 0,6 kg

Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.

Wood carving axe Zvenigorod VII was produced by Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.

8500p
Отзывов: 1
Рейтинг:

Chisel set PETROGRAD N13

Chisel set PETROGRAD N13:

Firmer gouge PETROGRAD 10mm
Bench chisel PETROGRAD 10mm
Bench chisel PETROGRAD 20mm
Skew chisel PETROGRAD, right-sided, 12mm
Skew chisel PETROGRAD, left-sided, 12mm
Corner chisel PETROGRAD 
Textile 16 pocket Tool Roll, PETROGRAD, 370*330mm, for chisels

11200p
Отзывов: 1
Рейтинг:

The book `Practical course of woodworking art` + Atlas of drawings, M. Netyksa

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

2200p
Отзывов: 1
Рейтинг:

The book `Practical course of woodturning art` + Atlas of drawings, M. Netyksa

The book is about woodturning art as a separate craft that includes not only the work on the lathe. This book was a basic textbook on turning wood and bone throughout the first half of the twentieth century. Moscow 1910 / Reprint edition of St. Petersburg 2017. Format 145x215 mm, hard tissue binding, 440 pages. Also included is an album of drawings attached to the 1910 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.

Division I. Machines, equipment and tools
Division II. Work techniques and special devices
Division III. Various materials in turning
Division IV. Adhesives, putties and surface grinding
Division V. Decoration and Surface Finishing Turning Works

1900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl, VII, curved handle

Hand forged outdoor axe Roslavl VII ( rus. Рославль VII ) with curved handle.

Total lenght is 370mm ( 14,57inch )
Height of axe is 140mm ( 5,51inch )
Lenght of cutting edge is 120mm ( 4,72inch )
Total weight of axe is 0,7kg  ( ± 0,05kg )

Axe is hand forged from "65Г" steel. Curved cutting edge was straight sharpened.
The axe comes with leather case for protecting cutting edge. Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint-Petersburg Russia.

8500p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 3000 grit

Water stones. Grain size: 3000 and 6000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Japan.

 

3030p
Отзывов: 1
Рейтинг: