Верстак 2000*600мм, с лотком, ПТ - коробка York HV511, БТ - York 516

Журнал Мастер и мастерская 2020 2 (9)

Long Moxon vise, wooden screws. This is one of the most suitable wooden vise for making woodworking joints and especially dovetails on wide boards. Jaws, handles and screws a made of wood, so you will never damage your sharp tools about it.

The vise must be installed on a workbench or other work surface such as massive table. This position is raising the workpiece to a comfortable height for sawing, marking and clear chisel cutting. The front jaw of vise is a clamping jaw. It is firmly fix the workpiece with two screws. Downside of front jaw protrudes downward for easy position vise flush to edge of surface.

• easily and quickly attachment to surface by any fast clamp or bench clamp
• easy vise position, flush to surface edge
• rise worpice for comfortable work
• max width of board for clamping - 550 mm (between screws)
• max thickness of workpice - 30mm (jaw opening)

We make our Moxon vises from solid beech wood, so you can't damage sharp edges of your tools while working with it and if needed you can always make part of it itself.

• vise is made of solid beech wood
• front jaw lenght - 500 mm
• jaw thickness - 45mm
• width between screws - 550 mm
• width of base plate - 100 mm
• lenght of base plate - 780 mm

This model of vise present with wooden screws and handles ( metal screw model here ). Wooden screws can be purchased separately.

• trapezoidal thread
• strong and fast clamp
• handles and screws made of hornbeam*

The Wooden Moxon vise by Petrograd toolworks was designed by Sergey Klein and was based on the early works of Anry Ruobo and Joseph Moxon. Vise have some changes from original work for more compliment work with dovetails and other woodworking joints. Moxon vise do not replace the classic workbench, but it is a devise that expands the arsenal of any master.

• overall dimensions: 780x145x120
• weight - 4.5 kg
• made of soliid beech
• oil coated

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Dimensions:	780x145x120 mm
Weight:	4.5 kg
Type:	for dovetailing
Jaw material:	beech
Handles:	wheel
Handles material:	hornbeam
Screws thread:	trapezoidal
Max width of board:	550 mm
Max thickness of workpice:	30 mm

* we recommend to use wax on screws for smooth and tight turning
** we reserve the right to make minor design changes to improve the vise performance.

Finishing oil PETROGRAD for workbenches and tool handles, 0.5l. Primer, used to apply the first coat before finishing. Recommended for use on hard or absorbent wood. Recommended for workbenches, tables, handles, woodworking tools and other woodworking parts. For indoor use only. It quickly and deeply penetrates the material and also quickly polymerizes.
Composition:
Tung oil, linseed oil, modified oils (linseed, tung, safflower, walnut), ricin oil, carnauba wax, micronized wax.
Mode of application:
Apply oil evenly to the prepared surface free of dirt and grease using a brush or lint-free cloth. After 10 minutes, wipe off the remaining oil from the surface with a dry, lint-free cloth. After 8 hours (depending on layer thickness and ambient temperature) apply a second coat. Ensure good ventilation of the room, both during application and at the end of work.
Note:
Certain oily, exotic or brightly colored woods and excessive amounts can prevent the oil from drying or greatly slow down the drying process. In this case, good ventilation is needed to speed it up.
- Do not use nitrile gloves for work.
- Safe for hands
- Always wear protective goggles when working.
Storage:
In a sealed container. It should be kept away from sources of fire and sparks.
Production - Russia.

Bench hold down Clamp is  a classic and efficient way for quick fixing workpieces to workbench top. Workbench clamp by Petrograd toolworks is manually hand forged by our blacksmiths and present a high quality piece of art to make you job easy and enjoyable.

• easy to use
• strong and save clamp
• extra fast clamping

To use hold down clamp you need to insert it into one of the bench holes for the stops in the workbench top and press down the workpiece. For more pressure can be used with wooden mallet.

• max height of clamped piace  - 120 mm
• diameter of the clamping rod is 16-17 mm
• to use with 19 mm holes ( 3/4 inch)
• for worbench top thick < 50 mm
  
• material - forged steel
• The size of the clamp is 290 x 200 mm. Material - steel.

Bench top camps are made by Petrograd toolworks in Saint-Petersburg Russia.

Hold down clamp Specifications:

Weight:	1.08 kg
Type:	hold down
Rod diameter:	16-17 mm
Material:	forged steel
Total lenght:	290 mm

 * material of handles may changes from batch to batch.