Categories
Workbench 2110*600 mm, with tray, front shoulder vise HV511, side shoulder vise HV519
- Основной склад: 3 шт.
Description
- workbench dimensions - 2000x600 mm
- bench top thickness - 40 mm
- workbench height - 850 mm
- opening width -170 mm.
- width of the movable jaw of the front vice - 250 mm
- height - 120 mm
- thickness - 60 mm
- width of the clamping part of the rear vise - 120 mm
- opening width - 150 mm.
A number of holes were drilled in the bench top to install the bench stops - 10 holes, +4 holes were drilled in the rear vise. In the frame board on the working side are also drilled 4 horizontal holes for the stops. Holes diameter - 19 mm. An additional upper pair of longitudinal crossbars is installed between the legs to strengthen the underlay.
- workbench material - beech sheet
- underbench and handles - solid beech
- top and underbench finished with tung oil
- workbench weight - approximately 95 kg
On the features of the installation of a joiner's workbench.
The workbench must be installed on a flat horizontal surface to avoid warping and deformation of the workbench. Benchboard dimensions with vise - 2182mm x 986mm. Workbench height - 850mm. Minor changes can be made to the design of the workbench without affecting its quality.
Bench stops included 4 pcs. All workbenches produced by the Rubankov company can be equipped with an additional vertical vice and a support board.
Production - factory Petrograd (Russia)
| Weight: | 95 kg |
|---|---|
| Type: | Joiners workbench |
| Material: | Beech |
| Front vise: | G-shape |
| Rear vise: | Box vise |
| Tray: | with tray |
| Lenght: | 2160 mm |
| Width: | 600 mm |
| Height: | 850 mm |
*The workbenches are made of solid beech and may have minor defects and flaws in the wood that do not affect the performance of the workbench. It is also possible a slight change in geometric dimensions during the annual change in humidity. If necessary, preventive leveling of the workbench is required (about once a year)
Are you sure?
Find out a mismatch? Highlight text and press Share / Save Link:
Видеоматериалы
Specs
Reviews
Instructions ()
Publications
Recommended products
Hold Down Clamp, PETROGRAD, type 1
Bench hold down Clamp is a classic and efficient way for quick fixing workpieces to workbench top. Workbench clamp by Petrograd toolworks is manually hand forged by our blacksmiths and present a high quality piece of art to make you job easy and enjoyable.
- easy to use
- strong and save clamp
- extra fast clamping
To use hold down clamp you need to insert it into one of the bench holes for the stops in the workbench top and press down the workpiece. For more pressure can be used with wooden mallet.
- max height of clamped piace - 120 mm
- diameter of the clamping rod is 16-17 mm
- to use with 19 mm holes ( 3/4 inch)
- for worbench top thick < 50 mm
- material - forged steel
- The size of the clamp is 290 x 200 mm. Material - steel.
Bench top camps are made by Petrograd toolworks in Saint-Petersburg Russia.
| Weight: | 1.08 kg |
|---|---|
| Type: | hold down |
| Rod diameter: | 16-17 mm |
| Material: | forged steel |
| Total lenght: | 290 mm |
Beech bench dog, 4 ps
These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia
Fan gasket for bench press
Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia
Popular goods
Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Sharpening set PETROGRAD N2, for woodworking tools, 6 stones
Sharpening set PETROGRAD N2. 
Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
| 150 | 360 | 500 | 800 | 1000 | 1500 | 2000 | |
| Sharpening set PETROGRAD N1 | + | + | + | ||||
| Sharpening set PETROGRAD N2 | + | + | + | + | + | + |
Comparison of FEPA, JIS and GOST standards:
Checkering tool complete N2-18, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N2-20, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Bit for checkering tool N2-18, 90°
Насадка на резец для чекеринга N2-18, 90° (две РК). Обе стороны с зубчиками. Используется для нанесения канавок и их углубления после нанесения. Одно лезвие проходит вдоль направляющей линии, в то время как другое намечает следующую канавку. При переходе на следующую канавку инструмент углубляет ее и снова наносит следующую канавку. Резец 2 Представляет из себя комбинацию инструментов для расширения и углубления канавок. Обе вершинки являются резцами.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering set, type N1, 90°/18lines, 6 tools + gauge, in roll bag
Checkering tool Set N1 (90 degrees, 18 lines) includes 6 tools for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 90 degree cutters, this type is making more sharp checkers that grants great grip and less prone to clogging than flat ones.
Set number 1 includes:
- gouge B-2 ( two cutting edges, spacer with tooths )
- gouge S-1 ( one cutting edge )
- gouge N2-18, 90° ( two cutting edges )
- gouge N3-18, 90° ( right router, left cutting edges )
- gouge N4-18, 90° ( left router, right cutting edges )
- gouge C-1, 90° ( one cutting edge )
- roll bag for carving tools ( 6 pockets )
- Checkering gauge
Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.
| Number of tools: | 6 tools |
|---|---|
| Type of checkers: | 90 degrees |
| Number of lines: | 18 lines on 1 inch |
| Handle material: | Beech* |
| Handle lenght: | 120 mm |
| Total lenght: | 240 mm |
| Total weight: | 0.3 kg |
1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °
2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm
4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle
6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees
Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.
Wooden spoon blanks set (Linden)
A set of blanks for making wooden spoons. The set includes two linden bars and 6 original patterns.
- Bars measuring 200x40x25mm and 200x30x22mm.
- Linden is a material for a beginner carver that does not require much work.
- Excellent sanding and tinting.
- Wood color is white.
- Great for subsequent painting.
Before starting work, it is recommended to copy the drawings for further use on other workpieces.
Wooden blanks by Petrograd toolworks. Made in Saint-Petersburg Russia.
Rule for sharpening guide
Carving knife PETROGRAD, skew type, 45 degrees
Нож для резьбы по дереву, ПЕТРОГРАДЪ, косая заточка 45град. Предназначен для широкого спектра работ. Рукоять выполнена из ясеня, угол скоса 45 градусов, инструментальная сталь. Производство фабрика Петроградъ (Россия).
Carving axe PETROGRAD, model Zvenigorod 7, handle n23
Топор для карвинга по дереву, ПЕТРОГРАДЪ, модель Звенигород 7, топорище н23. Резчицкий топор Звенигород предназначен для художественной обработки дерева: резьбы малых скульптурных форм, рубки посуды и прочих изделий. Небольшая масса топора делает его маневренным и позволяет работать деликатно и точно. Топор прекрасно держит свою остроту даже при малых углах заточки, что является обязательной составляющей для резьбы по дереву. Производство фабрика Петроградъ (Россия).