Share / Save Link:

Верстак школьный, 1060*1060мм, с лотком, тиски - n515 - 4 штуки



Rating : (1)
Shipping: worldwide

96000 p (1476.48)

Description

Верстак деревянный 1060*1060 мм, с лотком, тиски - HV515. Габариты верстачной доски - 1060х1060мм, толщина щита - 40мм. Обвязочная доска высотой 115мм с соединениями на "ласточкин хвост". На верстаке установлены 4 пары тисков с винтовыми парами York HW515. Производство фабрика Петроградъ (Россия).

  • ширина раскрытия тисков - 225мм
  • высота губок тисков - 110мм
  • толщина губок тисков - 50мм
  • ширина подвижной губки  тисков - 350мм

Губки тисков и подверстачье у этой модели прямые, не украшенные. Для установки упоров в столешнице просверлен ряд отверстий, 28 штук, +4 отверстие просверлено в задних тисках. В обвязочных досках с рабочих сторон также просверлено по 3 горизонтальных отверстия под упоры. Диаметр отверстий - 19мм.
В центральной части верстачной доски расположен лоток для мелких инструментов, глубина лотка - 35мм, ширина - 240 мм, длина - 980мм.

Подверстачь имеет 2 ноги и 4 проножки. Материал верстачной доски - буковый щит, подверстачье и рукояти - массив бука. Столешница и подверстачье покрыты маслом ПЕТРОГРАДЪ. Верстак необходимо устанавливать на ровную горизонтальную поверхность во избежание коробления и деформации верстачной доски. 

  • размер подверстачья - 975х975х810мм
  • сечение ножек - 90х45мм
  • высота верстака - 850мм
  • масса верстака - примерно 45кг.
  • верстак покрыт грунтовочным маслом марки Петроградъ *

Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Petrograd Аssembly Wood Table 1050*500, with 19mm hols

Верстак деревянный 1060*500мм, c пазом, без тисков (сборочный стол). Габариты верстачной доски - 1060х500мм, толщина щита - 40мм. Обвязочная доска высотой 120мм с соединениями на ласточкин хвост. Соединение ласточкин хвост - одно из самых  красивых и надежных столярных соединений, прочность которого проверена веками. На верстаке установлены передние переставные тиски и задние стационарные тиски. 
Теперь верстаки без лотка выполняются с центральным пазом. Паз закрыт Т-образной планкой, создающей либо поверхность с упором, либо ровную поверхность. Также при необходимости при удалении планки паз можно использовать для установки струбцин или упоров.

38000p(1476.48)
Отзывов: 1
>Рейтинг:

Workbench 2160*600 mm, with tray, front shoulder vise HV511, side shoulder vise HV510

The wooden workbench for carpentry and woodworking. It's a classic example of a workbench, which is known to everyone who had labor lessons at school in childhood (in Russia of course). The workbench is equipped with an G-shape front vise and a rear box vise. The frame board of the workbench has increased height and fixed by dovetail joints.

  • workbench dimensions - 2000x600 mm
  • bench top thickness - 40 mm
  • workbench height - 850 mm
148000p(1476.48)
Отзывов: 1
>Рейтинг:

Workbench 2000*600 mm, with tray, front vise - HV516, side vise - HV516

Габариты верстачной доски - 2000х600мм, толщина щита - 40мм. Обвязочная доска высотой 120мм с соединениями на ласточкин хвост. На верстаке установлены передние тиски и задние тиски York. Передние тиски с шириной раскрытия - 275мм. Ширина подвижной губки передних тисков - 410мм, высота - 120мм, толщина 60мм.Ширина задних тисков - 410мм. Высота верстака - 850мм. Масса верстака - примерно 90кг. Материал - бук. К заказу доступны 2 варианта комплектации: верстачная доска с подверстачьем и отдельно верстачная доска. Производство - мастерская Рубанков (Россия).

Для выбора верстака нужной комплектации нажмите на название товара
98000p(1476.48)
Отзывов: 1
>Рейтинг:

Carpenter drawknife PETROGRAD N5, Swedish type, 270mm

The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

7200p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 270mm

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

5300p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2060p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Natural lapping stone PETROGRAD, 200*70*20mm

Lapping stone from gabbro diabase. Used for lapping the soles of planes, abrasive stones and other surfaces. It has a perfectly smooth surface. Lapping is carried out with abrasive powders or diamond pastes. Approximate dimensions: 200x70x20 mm. Made in Russia.

2400p
Отзывов: 1
Рейтинг:
new

Froe PETROGRAD, model Uglich 300мм

Froe is a special cleaving axe (cleaver) for green woodworking, bodging and spoon making. Long blade and perpendicularly handle make it easy to split wood along the grain. Thick blade back would be good to use with mallet or even log*. Froe axe also good for split logs for fireplace, stove or even for making wood shingles and wooden blanks for spoons.

Edge is lenticular sharpened. Froe "Uglich" by petrograd toolworks is perfect choice for making blanks for spoon making. Froe axe is hand forged and totally made in Saint-Petersburg Russia

8000p
Отзывов: 1
Рейтинг:

The book `Practical course of woodworking art` + Atlas of drawings, M. Netyksa

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

2200p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

3440p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 3, double bevel

Leather Knife PETROGRAD, type 3, double bevel
The saddle knife is designed for cutting and roughing leather. Can be used for straight cuts and trimming of leather.
Produced in Russia at the PETROGRAD factory
4200p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, left-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

  • Knife blade width - 12mm.
  • Hook cutter length - 235 mm
  • Handle length - 160 mm
  • Hook knife blade made from tool steel and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

3600p
Отзывов: 1
Рейтинг: