Share / Save Link:

Magazine Master&Workshop 2019 5 (7)



Rating :
(1)
Shipping: worldwide

500 p (7.69)

Description

' ' 
:


:

- -

- ?

- « »
 
- «»
 
- « » « »
 
- ˨ - VERITAS ( )
 
-

-

-
«» 
- : « Ѩ »
WOODSIMKA 
- , ! ! ( )

-

-

-

-

-

- ( 5. )

- (. . )

-


« »
3000 .
6 .

Share / Save Link:

Specs

Reviews

Instructions ()

Publications

Sharpening set PETROGRAD N1, for woodworking tools, 3 stones

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

5240p
: 1
:

Center finding dowel/tenon pin set PETROGRAD, D5,6,8,10,12 mm, 2 pcs each

Centerfinding pins for furniture dowels. Diameter of punch: 5 mm, 6 mm, 8 mm, 10 mm, 12 mm.Totally hand made atPETROGRAD factory of joinery and carpentry tools.Made in Russia.

700p
: 1
:

Brass hammer PETROGRAD, model N1

This small brass hammer is designed for finishing trimming and driving parts requiring careful handling. Can be used to adjust the plane when setting the knife. Hammer head peens are flat. Turned polished strikers, hammer handle is made of cherry and covered with oil-wax. This tool in addition to the direct appointment also delivers aesthetic pleasure. The mass of the hammerhead is 125 g. The total length of the hammer is 320 mm. The size of the brass hammer striker - 70 x 16 mm (round section)

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Made in Russia.

2700p
: 1
:

Bit for checkering tool C-1, 60

C-1, 60° ( ) 1 . 90 60 . , . V- . -1 , , . . , , , ,   . , . .

- .

450p
: 1
:
new

Petrograd Brass Square 85mm, one-side marking

Elbow flat PETROGRAD, 85mm * 50mm. The square is one of the most used measuring tools in joinery. Ruler width 20 mm. Metric markings in 1 mm increments on the outside and inside. The error of the square is 0.05mm per 100mm. Used not only for checking 90 degree angles and marking, but also for setting up tools, saws and other tools. Material - brass. Engraved etched markings for easy reading.

Production of the PETROGRAD factory.

900p
: 1
:
new

PETROGRAD Center Finder, type 2, D100mm

Center finder, model n2, D100mm. Round center finder for marking and finding the center of the workpiece for turning. This is a measuring tool with which the center of the end face of cylindrical or arbitrary-shaped workpieces is found. The center-finder is made of polycarbonate. The maximum diameter of the measured workpiece is up to 100mm. Do not heat above 75 ° C. The step of the measuring scale is 10 degrees, from 0-100mm.

400p
: 1
:
new

Sharpening stone PETROGRAD, 153*15*15mm, 2000 grit

Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

680p
: 1
:
new

Sharpening stone PETROGRAD, 153*15*15mm, 500 grit

Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

480p
: 1
:
new

Sharpening stone PETROGRAD, 153*15*15mm, 360 grit

Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

410p
: 1
: