Мебель для токарной мастерской

The set includes:

Carving knife PETROGRAD, Bogorodsky type, 155mm/40mm
Carving knife PETROGRAD, Finnish type, 175mm/60mm
Carving knife PETROGRAD, skew 30 deg, 155mm/40mm
Carving knife PETROGRAD, Swedish type, 175mm/60mm
Spoon knife, PETROGRAD, D 27mm, right-handed
Carving chisel, PETROGRAD, 10mm
Textile 6 pocket Tool Roll, PETROGRAD, 360*260mm, for carving knives

The tools are made of steel 65G (Germany 66Mn4, Ck67, USA 1066) and have handles made of beech and maple covered with tung oil.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The right version of knife is designed to work with the right hand towards yourself or left hand to outside.

• Hook knife blade made from tool steel (9ХС) and hardened up to 58-60HRC.
• All hook cutters are sharpened and ready to go.
• The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
• The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

*coating may change from batch to batch

Leather fingertip is a thumb guard for wood carvers by Petrograd toolworks. Designed to protect hands from sharp tools. Thumb guard protects your finger from cut injuries when you are moving the cutting tool towards thumb, and prevents the formation of calluses when working away from yourself. Watch pictures for more info.

• made of 2mm natural leather
• easy to use
• save you from injures

Guard has a special ring that prevents it from slipping during operation. The thimble was made of 2mm soft leather, which provides good protection for the toe.

Thumb guard was made by Petrograd toolworks in Saint Petersburg Russia

Full tool set for checkering N3 (90 degrees, 18 lines) includes 10 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. This is most full set of tools for making checkers a on rifle handles. Gouges with 90 degree cutters in this set are making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 3 includes:

• gouge B-2 ( two cutting edges, spacer with tooths )
• gouge S-1 ( one cutting edge )
• gouge N2-18, 90° ( two cutting edges )
• gouge N3-18, 90° ( right router, left cutting edges )
• gouge N4-18, 90° ( left router, right cutting edges )
• gouge C-1, 90° ( one cutting edge )
• gouge L- 9, 90° ( right router with wide space, left cutting edge )
• gouge R- 9, 90° ( left router with wide space, right cutting edge )
• gouge for corners 90° (or Carving chisel, PETROGRAD, V-type, 90 degrees)
• gouge for marking rifle handles
• checkering guage
• roll bag for carving tools model N1 ( 12 pockets )

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
   It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
   Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
   The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
   The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °
2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm
4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle
6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Стамеска-ложкорез Петроград клюкарза N7, 30мм. Стамеска-ложкорез предназначена для создания ложек, кукс, а также прекрасно подойдет резьбы по дереву. Стамески клюкарзы используются для выполнения глубокой барельефной резьбы. Также удачно подходит для выборки углублений при резьбе посуды, кукс, ложек и декорировании деревянной поверхности.

Стамеска-ложкорез ПЕТРОГРАДЪ, клюкарза Swan Neck, н7,30мм – это прекрасный инструмент, позволяющий без особых усилий выбирать материал, при создании деревянных чаш, кукс и ложек. Эта стамеска выкована вручную из стали 9ХС и закалена до 61 HRc. Производство фабрика Петроградъ (Россия).