Share / Save Link:

Checkering set, type N1, 60°/18lines, 6 tools



Rating :
(1)
Shipping: worldwide

6900 p (106.12)

Description

Set N1 (60 degrees, 18 lines) includes 6 tools  for making checkers on wood.

Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 60° ( two cutting edges )
  • gouge N3-18, 60° ( right router, left cutting edges )
  • gouge N4-18, 60° ( left router, right cutting edges )
  • gouge C-1, 60° ( one cutting edge )
  • Checkering gauge
  • roll bag for carving tools ( 6 pockets )

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.


Share / Save Link:

Videos

youtube video
youtube video
youtube video

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Magazine Master&Workshop 2020 № 2 (9)

Журнал Мастер и мастерская 2020 2 (9)

500p(106.12)
Отзывов: 1
>Рейтинг:

Checkering gauge

600p(106.12)
Отзывов: 1
>Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 500 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

1620p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

1770p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 190mm/60mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1400p
Отзывов: 1
Рейтинг:

Spoon knife, PETROGRAD, type 1, D 27mm, left-handed

Spoon knife  (or shallow hook knife) is used to made wooden spoon, as well as for other similar work. Spoon knife blade is cutting out a hollow in a wooden spoon or scoop. Spoon knife N1 has a ring profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

  • Knife blade width - 8 mm.
  • The inner radius of the blade - 15mm.
  • Spoon cutter length - 45 mm
  • Handle length - 130 mm
  • Total length of the spoon knife - 175 mm
  • Spoon knife blade made from tool steel (9ХС; 150Cr14, 90CrSi, 90CrSi5) and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the ring has a convex lens-like shape and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

2400p
Отзывов: 1
Рейтинг:

Sharpening set PETROGRAD N4, for knives, 6 stones

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Production - made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

2380p
Отзывов: 1
Рейтинг:
new

Carving axe PETROGRAD, model Zvenigorod IX

Axe for artistic woodworking and sculpture making. This model was created according to the matrices of the Sweden axe GRANSFORS BRUKS SCULPTOR, building on the models of traditional craft axes. The relatively long, rounded blade with a wide and straight chamfer provides support for wood carving. The cutout on the axe allows you to keep it closer to head for more accurate work. The cutting edge length is 120 mm, the length of the axe is 360 mm. Weight 950 g. The axe is made of excellent steel 65G. The axe undergoes high-quality hardening and forging to a hardness of 58-60 HRc. Forging manually allows you to significantly increase strength. The handle is made of solid maple wood and impregnated with tung oil to prevent rotting. The axe is mounted on the handle with the help of two wooden wedges. Includes a genuine leather case for protecting blade. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia

8500p
Отзывов: 1
Рейтинг:

Carving set PETROGRAD, N5

Carving set PETROGRAD, N5
The set includes:
Carving knife PETROGRAD, Swedish type, 175mm/60mm
Sharpening stone PETROGRAD, 120*15*15mm, 1500 grit
Textile 4 pocket Tool Roll, PETROGRAD, 360*200mm
Carving chisel, PETROGRAD, dovetail, 12mm
Spoon knife, PETROGRAD, D 27mm, right-handed
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

5840p
Отзывов: 1
Рейтинг:
new

Outdoor axe PETROGRAD, model Roslavl, VII, curved handle

Hand forged outdoor axe Roslavl VII ( rus. Рославль VII ) with curved handle.

Total lenght is 370mm ( 14,57inch )
Height of axe is 140mm ( 5,51inch )
Lenght of cutting edge is 120mm ( 4,72inch )
Total weight of axe is 0,7kg  ( ± 0,05kg )

Axe is hand forged from "65Г" steel. Curved cutting edge was straight sharpened.
The axe comes with leather case for protecting cutting edge. Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint-Petersburg Russia.

8500p
Отзывов: 1
Рейтинг:

Bit for checkering tool N2-16, 60°

Насадка на резец для чекеринга N2-16, 60° (две РК). Обе стороны с зубчиками. Используется для нанесения канавок и их углубления после нанесения. Одно лезвие проходит вдоль направляющей линии, в то время как другое намечает следующую канавку. При переходе на следующую канавку инструмент углубляет ее и снова наносит следующую канавку. Резец 2 Представляет из себя комбинацию инструментов для расширения и углубления канавок. Обе вершинки являются резцами.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России

450p
Отзывов: 1
Рейтинг:

Bit for checkering tool S-1, 60°

Насадка на резец для чекеринга S-1, 60° (одна РК) имеет 1 пирамидальный зуб. Углы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резцы S-предназначен для обработки углов и изгибов, а также труднодоступных мест. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

450p
Отзывов: 1
Рейтинг: