Checkering set, type N1, 90°/18lines, 6 tools + gauge, in roll bag


  • Основной склад: 3 шт.
    Петербург: 1 шт.
    Москва: 1 шт.

Rating : (0)
Shipping: worldwide

6300 p (0)

Description

Checkering tool Set N1 (90 degrees, 18 lines) includes 6 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 90 degree cutters, this type is making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 90° ( two cutting edges )
  • gouge N3-18, 90° ( right router, left cutting edges )
  • gouge N4-18, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • roll bag for carving tools ( 6 pockets )
  • Checkering gauge
Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools:6 tools
Type of checkers:90 degrees
Number of lines:18 lines on 1 inch
Handle material:Beech*
Handle lenght:120 mm
Total lenght:240 mm
Total weight:0.3 kg

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.


Share / Save Link:

Видеоматериалы

youtube video
youtube video
youtube video

Specs

Reviews

Instructions ()

Нет файлов

Publications

%

Magazine Master&Workshop 2020 № 2 (9)

Журнал Мастер и мастерская 2020 2 (9)

500p(0)
Отзывов: 1
>Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2700p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Finnish type, 175mm/45mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

2500p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 60°

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

900p
Отзывов: 1
Рейтинг:

Checkering tool complete C-1, 90°

Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.

The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl 7, scandy bevel, handle n11

Hand forged outdoor axe Roslavl VII with curved handle. Axe as a woodworking tool has superior cutting abilities, short handle and would be good choiсe for any outdoor activity like campings, spoon making, making bonfire and etc. This axe is ideal for those who want take a small axe for different ways of use when you are going out and about in the countryside. Although it is light, it can be used to fell a small or even midle tree, thanks to its handle and heavy, strong head. The axe is also excellent for delimbing a tree and making wooden stakes.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

Axe Roslavl VII Specifications:
Head weight: 0.63 kg
Full weight: 0.7 kg
Type: outdoor hatchet
Steel: 65Г
Hardness: 55-58HRc
Handle material: Ash*
Handle lenght: 320 mm
Edge: Curved
Sharpening angle: 30 degrees
Blade lenght: 120 mm
Total lenght: 370 mm
 * material of handles may changes from batch to batch.
** coating oil may changes too
13000p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 1, double bevel

Leather Knife type 1 is a leather Head knife, also known as Round knife or even a Half-Moon knife. Head knife has double-sided sharpening. It's one of the oldest and most versality leather workning tool.

  • for straight cuts
  • for curved cuts
  • for skiving
  • for multiple layers cut

Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and reade to work out of the box.
This type of knives is used in handicraft, leather, and shoemaking.

  • blade made of tool alloy steel 9ХФ
  • blade thickness - 2 mm
  • edge radius - 61 mm
  • handle made of wood *
  • oil covered **

Handles are made of wood and fixed with 2 brass rivets. The kit includes a neat stitched leather case.
Knives for leather work are produced by Petrograd toolworks in Saint Petersburg Russia

Weight: 0.2 kg
Type: round knife
Steel: 9ХФ
Hardness: 58-61 HRc
Handle material: beech*
Handle lenght: 110 mm
Edge: curved
Sharpening: double sided
Blade lenght: 120 mm
Total lenght: 175 mm
 * material of handles may changes from batch to batch.
** coating oil may changes too
5130p
Отзывов: 1
Рейтинг:
new

Spoon knife, PETROGRAD, type 1/22, left-handed

Ложкорез по дереву ПЕТРОГРАДЪ модель N1/22, это инструмент для резьбы деревянных ложек и других впуклых поверхностей. Основная задача ложкореза - выборка лунки в деревянной ложке (черпало). Выпускается двух видов: правый и левый. Производство фабрика Петроградъ (Россия)

3200p
Отзывов: 1
Рейтинг:
new

Carving knife PETROGRAD, skew type, 45 degrees

Нож для резьбы по дереву, ПЕТРОГРАДЪ, косая заточка 45град. Предназначен для широкого спектра работ. Рукоять выполнена из ясеня, угол скоса 45 градусов, инструментальная сталь. Производство фабрика Петроградъ (Россия).

2500p
Отзывов: 1
Рейтинг:
new%

Outdoor axe PETROGRAD, model Roslavl X, handle

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25. Отличается от других топоров удлиненной режущей кромкой. Благодаря этой особенности топор можно брать близким к полотну хватом и не бояться поранить руку при работе. Такой хват очень удобен при тёске и ошкуривании бревен. Удлиненная рукоять позволяет без лишних усилий рубить ветки и сучья. Производство фабрика Петроградъ (Россия).

15000p
Отзывов: 1
Рейтинг:
new

Масло камелии, KAPLEUM, Лаванда, 60 мл.

Масло камелии, KAPLEUM, Лаванда, 60 мл. Неформальная творческая группа GILDIA.PRO предлагает новый продукт, изготовленный на основе отлично зарекомендовавшего себя масла Камелии – KAPLEUM.

 

720p
Отзывов: 1
Рейтинг: