Шлифовальная лента 50мм*2000мм, 400грит (А45), Trizact 253FA

Spoon knife (shallow hook knife).
Used to made a wooden spoons, as well as for other similar works.
The blade width is 8mm, the inner radius of the ring is 15mm. The outer side of the ring has a convex lens-like shape and is polished, which, together with the small width of the blade, allows you to cleanly and smoothly cut wood without scoring and steps.
The total length of the knife is 175 mm; the length of the handle is 130 mm.
Made of  9ХС (150Cr14, 90CrSi, 90CrSi5) steel, hardened to 58-60HRC.The convenient ergonomic oval handle of the knife is made of maple and impregnated with oil.
All knives are sharpened, finished and fully ready for work.
The right-handed version is designed to work with the right hand towards itself, the left-handed version - with the left hand towards itself.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia

Bench chisel PETROGRAD. The length of the blade 120mm; width - 20mm. Overall length 250mm.These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess. Chisels are made focusing on the experience of old masters of woodworking. The blade is made of high-alloyed chrome-manganese steel and hardened to 60HRc. Comfortable hornbeam handle. The handle at the junction with the blade reinforced brass ring with leather gasket. 

Special gouges with blackened blade, which tapers in hight. Forged blade is made of traditional Cr-Mn steel and is heat treated to 59 Hrc. Improved blade penetration into wood. Combination of the stained hornbeam handle, brass ferrule and improved griding of the blade creates unique design of the tool.

Marking knife PETROGRAD, with a flexible blade from steel 60SG2A (Germany 66Mn4, Ck67, USA 1066) is an ideal tool for marking the connections of the dovetail. The angle of formation of the arrow is 60 °, sharpening the blade with an angle of - 30 °. Blade thickness - 0.73mm, width - 9mm. Blade length - 40mm, knife length - 200mm. The handle is made of sapele wood covered with oil and shellac. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

Checkering tools from T-series has three cutting parts. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The beech handle is well balanced and easy to use.

At the same time cut all three blades with equally spaced teeth, so you can quickly apply the pattern immediately to a large area. This speeds up the process of drawing the picture, eliminates the additional effort. The lines are parallel with a single pass.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smooth turns every groove.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

The model range consists of straight chisels with an expanding blade with a working part width of 11 mm, 18 mm, 27 mm, 38 mm, 43 mm. They have a wide range of applications for carving, are one of the main knives in geometric carving, and are also convenient and in demand using the Whittling carving technique. Chisels are made of steel 65G (Germany 66Mn4, Ck67, USA 1066) and have handles of maple, covered with tung oil. Sharpening angle - 20 degrees, blade thickness - 2 mm.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia