Petrograd Carver's Table Vise



Rating : (1)
Shipping: worldwide

15000 p (230.7)

Description

This vise is a device that expands the arsenal of any master and not only a carver. The vice is installed on a workbench or other work surface, thereby raising the workpiece to a comfortable height for working with a cutting tool. They are attached to the working surface with clamps or jacks (not included). Solid beech vise. Hornbeam screws. Covered in oil.
The design of the vice is made using classic joinery joints, which provides them with high strength and stability. The considerable thickness of the upper shield and the height of the vice itself allows the use of jacks or clamps as clamps.
12 holes are drilled in the tabletop and 4 in the front jaw of the vise for the tuning pegs. This is done for the convenience of fixing flat blanks of various irregular shapes. Pegs are installed in these holes, which serve as stops for the workpiece. The vise clamping jaw with two screws firmly fixes the workpiece.

It is recommended to periodically lubricate the screws with wax for smooth running.
Overall dimensions: 480x490x130. The thickness of the jaws is 45mm. Tabletop thickness 43mm.

Maximum width of the workpiece to be clamped (distance between screws) 380mm.
Maximum workpiece thickness (screw travel) - 30mm.

We reserve the right to make minor design changes to improve vise performance.
The vice was developed by Sergey Aleksandrovich Klein.
Production of the PETROGRAD factory, Russia


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Straight Gouge Rubankov, N7, 10mm

Straight Gouge Rubankov, N7, 10mm (0.39 inches)

Carving chisel "Rubankov" Straight Gouge N7, 10mm (0.39 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 10mm ( 0.39 inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

3300p(230.7)
Отзывов: 1
>Рейтинг:
new

Magazine Master&Workshop 2021 № 2 (12)

Magazine Master and Workshop 2021 № 2 (12). This is a periodical magazine about woodworking, craftsmen and workshops, about the news of the carpentry world. The best masters share their knowledge and experience with everyone. Illustrated specialized full-color magazine.

on the cover: Fyodor Zhiltsov, master of furniture repair and restoration.
1000p(230.7)
Отзывов: 1
>Рейтинг:

Dead blow wooden mallet, round, 450 g

Dead blow wooden mallet, round shape. Mallets made by woodturning from solid wood with filling of metal balls (lead shot). Filling act as a weighting agent, and also reduce recoil upon impact. Mallet weight 450 gramm. Mallets made of beech wood and covered with tung oil. Round mallets used for working with mortise chisels and woodcarving chisels. It used when cutting joints and when carving large elements or sculptures (work from under the mallet).

Production of Petrograd toolworks. Made in Saint Petersburg Russia.

*blow without bounce

900p(230.7)
Отзывов: 1
>Рейтинг:

Hold Down Clamp, PETROGRAD, type 1

Clamp for quick fixing of workpieces. The clamp is hand forged. To use it, insert it into one of the holes for the stops in the workbench tabletop and press down the workpiece. Depth and height of workpiece clamping 120 mm. The diameter of the clamping rod is 16-17 mm. The size of the clamp is 290 x 200 mm. Material - steel.

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

3200p(230.7)
Отзывов: 1
>Рейтинг:

Sharpening set PETROGRAD N3, for knives, 3 stones

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

 

2900p
Отзывов: 1
Рейтинг:

Carving axe PETROGRAD, model Zvenigorod IX

Axe for artistic woodworking and sculpture making. This model was created according to the matrices of the Sweden axe GRANSFORS BRUKS SCULPTOR, building on the models of traditional craft axes. The relatively long, rounded blade with a wide and straight chamfer provides support for wood carving. The cutout on the axe allows you to keep it closer to head for more accurate work. The cutting edge length is 120 mm, the length of the axe is 360 mm. Weight 950 g. The axe is made of excellent steel 65G. The axe undergoes high-quality hardening and forging to a hardness of 58-60 HRc. Forging manually allows you to significantly increase strength. The handle is made of solid maple wood and impregnated with tung oil to prevent rotting. The axe is mounted on the handle with the help of two wooden wedges. Includes a genuine leather case for protecting blade. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia

10500p
Отзывов: 1
Рейтинг:

The book `Practical course of woodturning art` + Atlas of drawings, M. Netyksa

The book is about woodturning art as a separate craft that includes not only the work on the lathe. This book was a basic textbook on turning wood and bone throughout the first half of the twentieth century. Moscow 1910 / Reprint edition of St. Petersburg 2017. Format 145x215 mm, hard tissue binding, 440 pages. Also included is an album of drawings attached to the 1910 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.

Division I. Machines, equipment and tools
Division II. Work techniques and special devices
Division III. Various materials in turning
Division IV. Adhesives, putties and surface grinding
Division V. Decoration and Surface Finishing Turning Works

1900p
Отзывов: 1
Рейтинг:

Outdoor axe PETROGRAD, model Roslavl VII, handle n11

Hand forged outdoor axe Roslavl VII with curved handle.

  • Total lenght is 370mm ( 14,57inch )
  • Height of axe is 140mm ( 5,51inch )
  • Lenght of cutting edge is 120mm ( 4,72inch )
  • Axe is hand forged from 65G steel (Germany 66Mn4, Ck67, USA 1066).
  • Curved cutting edge was straight sharpened.
  • Total weight of axe is 0,7kg  ( ± 0,05kg )
  • Handle lenght is 320mm ( 12,6inch) and it is made from solid mapple with right grain position.
  • The axe comes with leather case for protecting cutting edge.

Axe is well balanced and would be a good choice for a lot types of work. It will be great as outdoor axe, for small carpentry and othe woodwork projects. This is kind of universal axe for everyone.

Axe Roslavl VII produced by Petrograd toolworks in Saint Petersburg Russia.

10500p
Отзывов: 1
Рейтинг:
%

Carving knife PETROGRAD, Bogorodsky type, 240mm/80mm

Нож резчицкий ПЕТРОГРАДЪ, Богородский, 240мм/80мм. Название этого инструмента для традиционной резьбы по дереву. Богородский нож имеет прямой короткий клинок. Успешно используется как для грубой, так и для тонкой резьбы.

Производство - фабрика столярных и плотницких инструментов 
Сделано в России

1700p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 3000 grit

Water stones. Grain size: 3000 and 6000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Japan.

 

2950p
Отзывов: 1
Рейтинг:
new

Axe Anika, model Jaeger 380mm, 850g

Топор Аника, Егерь, с чехлом. Легкий универсальный топор пригодится в походе, на даче, на охоте, рыбалке и даже в столярных и резчицких мастерских.
Скошенная фаска режущей кромки делает этот небольшой топор достаточно агрессивным. Этот кованый топор справится даже с валкой небольших деревьев. Егерь походный топор, садовый топор, резчицкий топор, охотничий топор, туристический топор, плотницкий топор и даже резчицкий топор. Рекомендуется любителям bushcraft и выживальщикам!
9000p
Отзывов: 1
Рейтинг:

Chisel handle n18

Рукоять для стамесок n17. Ручка имеет восьмигранную эргономичную форму. Не шлифована, ничем не покрыта, с кольцом. Латунное кольцо придает изысканный вид и предотвращает рукоять от растрескивания. Рукоять изготовлена из ценных пород древесины. Ударная сторона закруглена, чтобы не наминать мозоли на ладонях. В рукояти имеется отверстие для хвостовика стамески.

Производство фабрики столярных и плотницких инструментов ПЕТРОГРАДЪ

750p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 30mm

Bevel edge chisel Volga. These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess.

  • blade lenght - 150 mm
  • blade width - 30 mm
  • blade is made of high-alloyed chrome-manganese steel
  • hardened to 59-61 HRc
  • basic edge angle - 25 degrees
3100p
Отзывов: 1
Рейтинг:
new

Bevel edge chisel, PETROGRAD, model Volga, 8mm

Bevel edge chisel Volga. These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess.

  • blade lenght - 150 mm
  • blade width - 8 mm
  • blade is made of high-alloyed chrome-manganese steel
  • hardened to 59-61 HRc
  • basic edge angle - 25 degrees
2700p
Отзывов: 1
Рейтинг: