Carpenter axe PETROGRAD, model Kursk 15



Rating : (1)
Shipping: worldwide

10000 p (153.8) out of stock

Description

Топор плотницкий ПЕТРОГРАДЪ, модель Курск 15, топорище н31 – это добротный универсальный топор. Длинное топорище и клиновидная форма головы позволяют использовать его для колки небольших поленьев и рубки небольших деревьев. Производство фабрика Петроградъ (Россия).

Характеристика топора:

  • Сталь: 65Г
  • Закалка: 58 HRc
  • Масса: 1500 грамм
  • Общая длина: 500мм
  • Длина рукояти: 430мм
  • Длина режущей кромки: 110 мм
  • Рукоять: ясень
  • В комплекте 2 чехла

Представленный топор имеет прямую заточку под углом 30 градусов. За счет клиновидной формы головы обладает прекрасными рубящими свойствами. Угол заточки 30 градусов, что обеспечивает дополнительную стойкость режущей кромки.


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Spoon axe PETROGRAD, model Semeonov, handle n30

Топор ложкарный ПЕТРОГРАДЪ, модель Семёнов. Это малый кованый топор, предназначенный для грубой обтески будущих ложек. Производство фабрика Петроградъ (Россия).

9800p(153.8)
Отзывов: 1
>Рейтинг:
new

Outdoor axe PETROGRAD, model Roslavl X, handle

Топор кованый ПЕТРОГРАДЪ, модель Рославль 10, топорище н25. Отличается от других топоров удлиненной режущей кромкой. Благодаря этой особенности топор можно брать близким к полотну хватом и не бояться поранить руку при работе. Такой хват очень удобен при тёске и ошкуривании бревен. Удлиненная рукоять позволяет без лишних усилий рубить ветки и сучья. Производство фабрика Петроградъ (Россия).

14000p(153.8)
Отзывов: 1
>Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 1000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

 

2300p
Отзывов: 1
Рейтинг:
new

Carving knife PETROGRAD, Swedish type, 180mm/40mm

Carving knives with a straight butt and a curved cutting edge are great for strength work. Blade length 45mm or 60mm. The length of the handle - 115mm. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Strop PETROGRAD, two-sided, 200mm*70mm

Double-sided bar with glued leather. The size of the bar is 200x70x25mm. It can be used with polishing pastes. Material - ash, leather - "reversal" 2mm. Skin color may differ from the image on the site. Made in Russia.

950p
Отзывов: 1
Рейтинг:

Cutting knife PETROGRAD, double bevel 30 deg, 20mm/167mm

Knives jambs with a bevel angle of 30 degrees. The blade length is shown in the table, the blade thickness is about 2 mm. The blade is made of 65G (Germany 66Mn4, Ck67, USA 1066) steel hardened of 59-61 HRc. Sharpened and ready to go. Knives with a slanting sharpening have a wide range of applications (in carving, for marking, when working with cardboard, modeling and in everyday life).

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

3100p
Отзывов: 1
Рейтинг:
new

Carving set PETROGRAD, N2

The set includes:

Carving knife PETROGRAD, Bogorodsky type, 155mm/40mm
Carving knife PETROGRAD, Finnish type, 175mm/60mm
Carving knife PETROGRAD, skew 30 deg, 155mm/40mm
Carving knife PETROGRAD, Swedish type, 175mm/60mm
Spoon knife, PETROGRAD, D 27mm, right-handed
Carving chisel, PETROGRAD, 10mm
Textile 6 pocket Tool Roll, PETROGRAD, 360*260mm, for carving knives

 

 

 

 

15000p
Отзывов: 1
Рейтинг:

Strop PETROGRAD, for carving tools, 150mm*30mm

The bar with glued leather is designed for finishing semi-circular chisels, drawknives, etc. One of the flat sides can also be used for fine-tuning of flat tools. The size of the bar is 150x30 mm. Min radius - 3 mm, max. radius -6 mm. It can be used with polishing pastes. Material - ash, leather - reversal 2mm. Leather color may differ from the image on the site. Made in Russia.

900p
Отзывов: 1
Рейтинг:

Leather fingertip for woodcarvers

Leather fingertip is a thumb guard for wood carvers by Petrograd toolworks. Designed to protect hands from sharp tools. Thumb guard protects your finger from cut injuries when you are moving the cutting tool towards thumb, and prevents the formation of calluses when working away from yourself. Watch pictures for more info.

  • made of 2mm leather
  • easy to use
  • save you from injures

Guard has a special ring that prevents it from slipping during operation. The thimble was made of 2mm soft leather, which provides good protection for the toe.

Thumb guard was made by Petrograd toolworks in Saint Petersburg Russia

600p
Отзывов: 1
Рейтинг:

Checkering set, type N3, 90°/18lines, 10 tools + gauge, in roll bag

Set N3 (90 degrees, 18 lines) includes 10 tools  for making checkers on wood.

Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Set number 3 includes:

gouge B-2 ( two cutting edges, spacer with tooths )
gouge S-1 ( one cutting edge )
gouge N2-18, 90° ( two cutting edges )
gouge N3-18, 90° ( right router, left cutting edges )
gouge N4-18, 90° ( left router, right cutting edges )
gouge C-1, 90° ( one cutting edge )
gouge L- 9, 90° ( right router with wide space, left cutting edge )
gouge R- 9, 90° ( left router with wide space, right cutting edge )
gouge for corners 90° (or Carving chisel, PETROGRAD, V-type, 90 degrees)
gouge for marking rifle handles
checkering guage
roll bag for carving tools model N1 ( 12 pockets )

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.

10290p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 2000 grit

Water stone. 2000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

2560p
Отзывов: 1
Рейтинг:
new

Прибор для выжигания 'Тесла'

Прибор для выжигания "Тесла". Профессиональный выжигательный электроприбор "ТЕСЛА" предназначен для декорирования деревянной поверхности и выжигания на фанере, на дереве или фанере, коже и кости.

Комплект поставки:

  • Блок питания
  • Силовой гибкий кабель в оплетке
  • Две сменные ручки
  • Руководство по эксплуатации.
10000p
Отзывов: 1
Рейтинг: