PETROGRAD Glue Press, type 2, 910mm



Rating : (1)
Shipping: worldwide

8550 p (131.5)

Description

Вайма ПЕТРОГРАДЪ, модель 2, 910мм – это усовершенствованная версия модели номер 1. Используется для склейки деревянных щитов и делянок толщиной до 100мм. Отличительной особенностью являются ножки, благодаря наличию которых вайма стала более устойчивой. Производство фабрика Петроградъ (Россия).

Характеристики ваймы:

  • Ширина склеиваемого щита до 910 мм
  • Усилие на сжатие 800 кПа.
  • Минимальная толщина склеиваемого щита 25 мм
  • Максимальная толщина склеиваемого щита 100 мм
  • Имеет ножки

Очередной приятной особенностью ваймы является то, что она может быть сложена в транспортировочное состояние, при котором общая длина снижается до 15 см. Сокращение длина достигается посредством перевода шарнира петель внутрь направляющих. Именно в таком состоянии вайма отправляется при доставке транспортной компанией.

Прижимной блок из высокопрочной стали обеспечивает высокое равномерное давление на ламели. Прочный винт обеспечивает качественный прижим. В процессе эксплуатации винт необходимо очищать от опилок и смазывать любым машинным маслом. Это значительно увеличит срок службы инструмента. Благодаря специальной конструкции вайм на склеиваемые заготовки оказывается равномерное давление с 4-х сторон. Это обеспечивает прочную склейку без щелей при условии качественной прифуговки делянок и качественного клея. Два съёмных упорных штифта со съемной шпилькой позволяют оперативно переставлять задний упор для регулировки необходимых размеров.


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

PETROGRAD Glue Press 100cm*10cm

It is used for gluing wooden boards and plots up to 100mm thick. The pressure block made of high-strength steel ensures high uniform pressure on the lamellas. The minimum and maximum thickness of the glued board varies from 25mm to 100mm.

Thanks to the special design of the clamp, uniform pressure is exerted on the workpieces to be glued from 4 sides. This ensures a strong gluing without gaps, provided that the plots are properly planed and glue is of good quality.

Two removable stop pins with a removable pin allow you to quickly rearrange the backgauge to adjust the required dimensions.

Trapezoidal screw length - 250, diameter - 23mm, thread pitch 3mm. (Attention. During operation, the screw must be cleaned of sawdust and lubricated with any machine oil. This will significantly increase the service life of the tool). The guides are made of a rectangular profile 60x30mm and have a wall thickness of 2mm. The clamps are painted with impact-resistant paint.


Made in Russia
12700p(131.5)
Отзывов: 1
>Рейтинг:

Wooden fore plane PETROGRAD, 455mm/60mm

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil. The wedge is also made of maple. The installation angle of the knife is 50 ° -55 °. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 60 mm, knife thickness minimum 2.2 mm, maximum thickness - 3.5 mm. Sharpening angle 30 °. Dimensions of jointer plane 455 * 80 * 170 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

16000p(131.5)
Отзывов: 1
>Рейтинг:
%

Wheel marking gauge Petrograd, type 1

Рейсмус разметочный, диапазон разметки 0 - 150мм. Предназначен для разметки шиповых соединений, фальцев, гнезд, используется при установке петель, при разметке параллельных деталей перед их фуговкой.

4000p(131.5) 4 500 p
Отзывов: 1
>Рейтинг:

Carpenter drawknife PETROGRAD N5, Swedish type, 270mm

The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

7200p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 270mm

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

5300p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2060p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Natural lapping stone PETROGRAD, 200*70*20mm

Lapping stone from gabbro diabase. Used for lapping the soles of planes, abrasive stones and other surfaces. It has a perfectly smooth surface. Lapping is carried out with abrasive powders or diamond pastes. Approximate dimensions: 200x70x20 mm. Made in Russia.

2400p
Отзывов: 1
Рейтинг:
new

Froe PETROGRAD, model Uglich 300мм

Froe is a special cleaving axe (cleaver) for green woodworking, bodging and spoon making. Long blade and perpendicularly handle make it easy to split wood along the grain. Thick blade back would be good to use with mallet or even log*. Froe axe also good for split logs for fireplace, stove or even for making wood shingles and wooden blanks for spoons.

Edge is lenticular sharpened. Froe "Uglich" by petrograd toolworks is perfect choice for making blanks for spoon making. Froe axe is hand forged and totally made in Saint-Petersburg Russia

8000p
Отзывов: 1
Рейтинг:

The book `Practical course of woodworking art` + Atlas of drawings, M. Netyksa

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

2200p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

3440p
Отзывов: 1
Рейтинг:

Leather Knife PETROGRAD, type 3, double bevel

Leather Knife PETROGRAD, type 3, double bevel
The saddle knife is designed for cutting and roughing leather. Can be used for straight cuts and trimming of leather.
Produced in Russia at the PETROGRAD factory
4200p
Отзывов: 1
Рейтинг:

Shallow Hook Knife, PETROGRAD, type 3, left-handed

Hook knife is used for cutting out a hollow in a wooden spoon or scoop, as well as for other similar work. Shallow hook knife N3 has a water drop profile of blade. That's making it perfectly choose for cut wooden spoons bowl. The left version of knife is designed to work with the left hand towards yourself or right hand to outside.

  • Knife blade width - 12mm.
  • Hook cutter length - 235 mm
  • Handle length - 160 mm
  • Hook knife blade made from tool steel and hardened up to 58-60HRC.
  • All hook cutters are sharpened and ready to go.
  • The outerside of the hook is ring-shaped and perfectly polished. Thats allow you to cut wood cleanly and smoothly without scoring.
  • The handle of the hook knife is made of maple and coated with oil.

The right version of hook knife is designed to work with the right hand towards yourself, the left version - with the left hand towards yourself.
Made by Petrograd toolworks in Saint-Petersburg Russia.

3600p
Отзывов: 1
Рейтинг: