Petrograd Аssembly Wood Table 1050*500, with 19mm hols

The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

Lapping stone from gabbro diabase. Used for lapping the soles of planes, abrasive stones and other surfaces. It has a perfectly smooth surface. Lapping is carried out with abrasive powders or diamond pastes. Approximate dimensions: 200x70x20 mm. Made in Russia.

Froe is a special cleaving axe (cleaver) for green woodworking, bodging and spoon making. Long blade and perpendicularly handle make it easy to split wood along the grain. Thick blade back would be good to use with mallet or even log*. Froe axe also good for split logs for fireplace, stove or even for making wood shingles and wooden blanks for spoons.

Edge is lenticular sharpened. Froe "Uglich" by petrograd toolworks is perfect choice for making blanks for spoon making. Froe axe is hand forged and totally made in Saint-Petersburg Russia

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.