Верстак деревянный 1060*500мм, с лотком, ПТ - HV515, БТ - HV515, авторская работа Михаила Зелинского



Rating : (1)
Shipping: worldwide

38000 p (584.44) out of stock

Description

Верстак столярный, характеристики и особенности

Данный верстак является авторской работой Михаила Зелинского. Верстачная доска украшена элементами из красного дерева «полет ласточки». Губки тисков выполнены с декоративными вставками из красного дерева. 

Габариты верстачной доски - 1060х500мм, толщина щита - 40мм. Обвязочная доска высотой 115мм с соединениями на ласточкин хвост"На верстаке установлены передние (фронтальные) тиски и задние (боковые) тиски. Передние и задние тиски сделаны на основе металлической винтовой пары от фирмы York (Чехия), ширина раскрытия - 225мм. Ширина подвижной губки передних тисков - 350мм, высота - 110мм, толщина - 50мм. Ширина задних тисков . Для установки упоров в столешнице просверлен ряд отверстий, 14 штук, отверстие просверлено в задних тисках. В обвязочной доске с рабочей стороны также просверлены 3 горизонтальных отверстия под упоры. Диаметр отверстий - 19мм.

В задней части верстачной доски расположен лоток для мелких инструментов, глубина лотка - 35мм, ширина - 180мм, длина - 980мм.

Для усиления подверстачья между ножками установлена дополнительная верхняя пара продольных перекладин. Материал верстачной доски - буковый щит, подверстачье и рукояти - массив бука. Столешница и подверстачье покрыты маслом. Верстак необходимо устанавливать на ровную горизонтальную поверхность во избежание коробления и деформации верстачной доски. Размер подверстачья - 1060х500х800мм, сечение ножек - 90х45мм. Высота верстака - 850мм. Масса верстака - примерно 45кг.

В конструкцию верстака могут вноситься небольшие изменения, не влияющие на его качество. Верстачные упоры продаются отдельно. На все столярные верстаки производства компании Рубанков можно установить дополнительные вертикальные тиски и опорную доску.  Верстак так же можно доукомплектовать подверстачной тумбой для инструментов. Производство - мастерская Рубанков (Россия)

Столярный верстак выполнен из массива бука и может иметь незначительные дефекты и пороки древесины не влияющие на эксплуатационные качества деревянного столярного верстака. Также возможно незначительное изменение геометрических размеров в течении годового изменения влажности. При необходимости требуется профилактическое выравнивание верстака (примерно раз в год

"


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Beech bench dog, 4 ps

These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

800p(584.44)
Отзывов: 1
>Рейтинг:

Hold Down Clamp, PETROGRAD, type 1

Clamp for quick fixing of workpieces. The clamp is hand forged. To use it, insert it into one of the holes for the stops in the workbench tabletop and press down the workpiece. Depth and height of workpiece clamping 120 mm. The diameter of the clamping rod is 16-17 mm. The size of the clamp is 290 x 200 mm. Material - steel.

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

3200p(584.44)
Отзывов: 1
>Рейтинг:

Strop PETROGRAD, one-sided, 200mm*70mm

One-sided bar with glued leather. The size of the bar is 200x70x22mm. It can be used both with polishing pastes and without them. Material - ash, leather - smooth - 2mm. Made in Russia.

850p
Отзывов: 1
Рейтинг:
new

Strop PETROGRAD, two-sided, 200mm*70mm

Double-sided bar with glued leather. The size of the bar is 200x70x25mm. It can be used with polishing pastes. Material - ash, leather - "reversal" 2mm. Skin color may differ from the image on the site. Made in Russia.

950p
Отзывов: 1
Рейтинг:
new

Sharpening set PETROGRAD N2, for woodworking tools, 6 stones

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

13970p
Отзывов: 1
Рейтинг:

Strop PETROGRAD, for carving tools, 150mm*30mm

The bar with glued leather is designed for finishing semi-circular chisels, drawknives, etc. One of the flat sides can also be used for fine-tuning of flat tools. The size of the bar is 150x30 mm. Min radius - 3 mm, max. radius -6 mm. It can be used with polishing pastes. Material - ash, leather - reversal 2mm. Leather color may differ from the image on the site. Made in Russia.

900p
Отзывов: 1
Рейтинг:
new%

Carving adze PETROGRAD, type N1, half round, external bevel

Wood carving adze by PETROGRAD toolworks.

This adze was developed taking into account the wishes of artisans, as well as our experience in creating carpentry and carving tools. The carving adze is intended for chiseling the internal cavity when creating dishes (trough, broths, cups, bowls, plates, etc.), as well as for roughing the outer surfaces. Scope due to the size of adze.

Developed and designed carving adze - V. Sasin.

The ergonomic handle allows you to securely hold the tool during operation. Expansion at the end of the handle prevents slipping from the hand. The adze handle made of maple and covered with oil. Maple - one of the best wood for the manufacture of handles.

Hand forged blade from steel 65G (Germany 66Mn4, Ck67, USA 1066). Together with the handle has a mass of about 750 grams. Cutting edge sharpening angle - 30 degrees. The width of the working part - 40mm. Cutting edge bending radius - 20mm. If to speak it is applicable to the carving tool  - it is 9 profile.

The eye has a wedge shape. The adze handle slides and splits into 3 wedges.

Sharpening the cutting edge - chamfer outside. It is preferable to use this adze at the finishing stages, for stripping, for smooth formation of the transition from the vertical wall to the flat bottom.

Any carving adze can be used from the beginning to the end. With experience comes the understanding that all three models must be in the arsenal.

Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

9200p
Отзывов: 1
Рейтинг:

Petrograd Bevel Gauge, 85mm*55mm

Шаблон угломер ПЕТРОГРАДЪ. 13 вырезов под углы - 15°, 20°,22.5° 25°, 27.5°, 30°, 32.5°, 35°, 37.5°, 40°, 45°, 90°, 120° глубина вырезов - 9 мм. Ширина шаблона - 54 мм, Длина шаблона 85 мм. На конце вырезов имеется отверстие, что позволяет использовать шаблон для определения других углов проводя интерполяцию (н-р угол 24° или 26°, используя вырез на 25°). Выполнен из латуни. Удобный и компактный шаблон используется для проверки углов при заточке стамесок, резцов, ножей рубанков и тп.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России.

1200p
Отзывов: 1
Рейтинг:
%

Polishing Paste 1200 grit 180 g

Waxy polishing pastes in the form of a rectangular bar. Dimensions - 60x60x15mm. Granularity - coarse, medium and fine. Brown 1200grit Weight - 180g. Used for grinding and polishing on wheels, belts, etc. Perfect for hand-held leather bars Petrograd.

Ingredients: a mixture of grinding powders, binders and auxiliary elements kerosene, stearin, sodium bicarbonate, silica gel.

Made in Russia.

720p
Отзывов: 1
Рейтинг:
new

Axe Anika, model Tomohawk

Топор Аника, Томагавк, с чехлом. Ультра-легкий топор Томагавк с обухом-молотком. Идеальный инструмент для передвижений налегке и хозяйственной деятельности в лесу. Заточка с микроподводом для работ по сухой и сырой древесине. Вес головы — около 600 грамм. Вес топора — около 800 грамм. Общая длина — 400-450 мм.
7900p
Отзывов: 1
Рейтинг:
new

Checkering set, type N1, 90°/16lines, 6 tools + gauge, in roll bag

Checkering Set N1 (90 degrees, 16 lines) includes 6 tools for making checkers on wood. Set of gouges with 90 degree cutters, this type is making more sharp pointed checkers that grants stronger grip.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 90° ( one cutting edge )
  • gouge N2-16, 90° ( two cutting edges )
  • gouge N3-16, 90° ( right router, left cutting edges )
  • gouge N4-16, 90° ( left router, right cutting edges )
  • gouge C-1, 90° ( one cutting edge )
  • Checkering gauge
  • roll bag for carving tools ( 6 pockets )
6100p
Отзывов: 1
Рейтинг: