Workbench 2000*600 mm, with tray, front vise - HV516, side vise - HV516



62000 p (860.56) out of stock
Rating :
Avg. value 0 (by rates of 0 users)

Description

Габариты верстачной доски - 2000х600мм, толщина щита - 40мм. Обвязочная доска высотой 120мм с соединениями на ласточкин хвост. Соединение ласточкин хвост - одно из самых  красивых и надежных столярных соединений, прочность которого проверена веками. На верстаке установлены передние (фронтальные) тиски и задние (боковые) тиски. Передние и задние тиски сделаны на основе металлической винтовой пары от фирмы York (Чехия), ширина раскрытия тисков - 275мм. Ширина подвижной губки передних тисков - 410мм, высота - 120мм, толщина - 60мм. Ширина задних тисков - 410мм. Губки тисков и опоры подверстачья украшены легким фрезерным узором. Для установки упоров в столешнице просверлен ряд отверстий, 32 штуки , отверстия просверлено в задних тисках. В обвязочной доске с рабочей стороны также просверлены 6 горизонтальных отверстия под упоры, отверстие в губке задних тисков. Диаметр отверстий - 19мм. В задней части верстачной доски расположен лоток для мелких инструментов, глубина лотка - 35мм, ширина - 150мм, длина - 1920мм. Для усиления подверстачья между ножками установлена дополнительная верхняя пара продольных перекладин. Материал верстачной доски - буковый щит, подверстачье и рукояти - массив бука. Столешница и подверстачье покрыты тунговым маслом фирмы Borma. Размер подверстачья - 1500х600х800мм, сечение ножек - 90х45мм. Высота верстака - 850мм. Верстак необходимо устанавливать на ровную горизонтальную поверхность во избежание коробления и деформации верстачной доски. Масса верстака - примерно 60кг. В конструкцию верстака могут вноситься небольшие изменения, не влияющие на его качество. Верстачные упоры продаются отдельно. Верстак так же можно доукомплектовать подверстачной тумбой для инструментов. К заказу доступны 2 варианта комплектации: верстачная доска с подверстачьем и отдельно верстачная доска. Производство - мастерская Рубанков (Россия).

Верстаки выполнены из массива бука и могут иметь незначительные дефекты и пороки древесины не влияющие на эксплуатационные качества верстака. Также возможно незначительное изменение геометрических размеров в течении годового изменения влажности. При необходимости требуется профилактическое выравнивание верстака (примерно раз в год).

Посмотреть виртуальный мастер-класс по изготовлению верстака.


l

Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

500p(860.56) In stock

These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia

340p(860.56) In stock

Clamp for quick fixing of workpieces. The clamp is hand forged. To use it, insert it into one of the holes for the stops in the workbench tabletop and press down the workpiece. Depth and height of workpiece clamping 120 mm. The diameter of the clamping rod is 17 mm. The size of the clamp is 290 x 200 mm. Material - steel.

Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia

2 500p(860.56) In stock

Spoon knife (shallow hook knife).
Used to made a wooden spoons, as well as for other similar works.
The blade width is 8mm, the inner radius of the ring is 15mm. The outer side of the ring has a convex lens-like shape and is polished, which, together with the small width of the blade, allows you to cleanly and smoothly cut wood without scoring and steps.
The total length of the knife is 175 mm; the length of the handle is 130 mm.
Made of  9ХС (150Cr14, 90CrSi, 90CrSi5) steel, hardened to 58-60HRC.The convenient ergonomic oval handle of the knife is made of maple and impregnated with oil.
All knives are sharpened, finished and fully ready for work.
The right-handed version is designed to work with the right hand towards itself, the left-handed version - with the left hand towards itself.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia

2 100p

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

1 350p

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
900p

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

630p

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

4 910p

Carving knives with a bevel angle of 30, 37, 40 degrees double-sided sharpening. Blade length - 40 mm, width 13 mm, straight butt. A comfortable maple oval handle is saturated with oil and covered with shellac. The length of the handle - 115 mm. Knife for a wide range of works. The 2.5 mm thick blade is made of 65G (Germany 66Mn4, Ck67, USA 1066) steel,  hardened to 59-61 HRc. Sharpened and ready to go.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

 

900p

Cylindrical water stones. Grain size: 240, 500, 1000. Size D15*120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

1 830p
%

Marking knives PETROGRAD have a unilateral right or left sharpening and bevel at an angle of 30 and 45 degrees. The blade of the knife is made of high carbon steel and hardened to 59HRC, it passes through the entire handle - this allows you to use it not only as a marking knife, but also as a power knife jamb. Blade thickness - 1.7mm, width - 19mm. The lining is made of beech wood, covered with tung oil and fastened with brass rivets. The length of the knife is 165mm, the blade is 70mm.

900p

Carving knives for general use, as well as for large material removal. Blade length 56 mm or 38 mm, beveled butt. Comfortable oval maple handle soaked in oil. The length of the handle - 130mm. Excellent knife for both beginners and professionals. The 1.8 mm thick blade is made of 65G high carbon steel (Germany 66Mn4, Ck67, USA 1066), hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools.Made in Russia.

900p

Tool Roll is designed to store short chisels and knives in the amount of up to 4 pieces. The bag is made of black fabric -100% cotton. The maximum tool length is 180 mm. The length of the tool roll in expanded form - 360 mm, width 200 mm. Compartment for chisels has a strap - to close the cutting part. Lacing is provided for fixing the twist bag. Made in Russia.

350p