Magazine Master&Workshop 2021 № 2 (12)

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.

It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.

Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.

The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.

The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Abrasive water stones. Grit: 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

Abrasive water stones. Grit: 120, 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

Bevel edge chisel Volga. These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess.

• blade lenght - 150 mm
• blade width - 26 mm
• blade is made of high-alloyed chrome-manganese steel
• hardened to 59-61 HRc
• basic edge angle - 25 degrees

 Chisels are made focusing on the experience of old masters of woodworking. Comfortable handle. The handle at the junction with the blade reinforced brass ring.

• handle lenght - 130 mm
• overall length - 280 mm

Made by Petrograd toolworks in Saint Petersburg Russia.

Верстак настольный 500*350мм, Shipmodeller. Этот верстак выполнен из массива бука и предназначен для установки на любую удобную вам поверхность. Наилучшим образом подходит для небольших работа по дереву, таких, как судомоделизм. Производство фабрика Петроградъ (Россия).