High-precision marking gauge for woodworking intended for marking mortise, tenons, finger joints, bridle joints and etc. Gauge also can be use for installing hinges and marking alot of parallel parts in woodworking.

• Measurement range 0-180 mm.
• The rod is 235 mm long and is made of hardened steel.
• Steel rod diameter 7mm.
• The stop is made of stainless steel with a diameter of 59 mm.
• Microadjustment mechanism with a convenient adjusting wheel.
• Micro-adjustment range up to 7 mm.
• One revolution of the micro-adjustment wheel is 0.5 mm

Marking gauge suitable for marking:

• mortise and tenons
• bridle joints
• finger joint depth
• dovetail joints depth
• parallel hand planing line

Production of Petrograd toolworks. Made in Saint-Petersburg Russia.

Diamond stones for sharpening knives, small chisels, cutting tools and other tools. The sharpening stones are designed for cutting high carbon steels. Diamond stones are a monolithic bar 150 x 12 mm with a continuous diamond layer (dusting). The diamond-bearing layer of grinding stones is made of synthetic diamond micropowders on a copper-tin bond M2-01.

Chisel PETROGRAD flat with a straight cutting edge, for wood. Blade length - from 120mm to 160mm; width - 3mm, 4mm, 5mm, 6mm, 8mm, 10mm, 12mm, 16mm, 20mm, 26mm, 32mm, 40mm, 50mm. The total length is from 250mm to 295mm. The blade is made of high-alloy chrome-manganese tool steel and hardened to 60HRc. The handle is made of hornbeam wood, the size of the handle is 130x30mm and 135x30mm. Uncoated handle - the craftsman chooses the finish himself. The handle at the junction with the blade is reinforced with a brass ring with a leather lining. There are also sets of chisels in a twist bag.

Наводка для цикль, ПЕТРОГРАДЪ, модель 2. Имеет закаленный стержень с круглым сечением для нанесения грата и деформации кромок цикль. Двусторонняя рукоятка обеспечивает превосходное управление для равномерного распределения усилий при заточке цикль. Подходит для заточки, как прямых так и криволинейных форм.

Стамеска  ПЕТРОГРАДЪ плоская с прямой режущей кромкой, по дереву. Длина полотна - от 120мм до 160мм; ширина - 3мм, 4мм, 5мм, 6мм, 8мм, 10мм, 12мм, 16мм, 20мм, 26мм, 32мм, 40мм, 50мм. Общая длина - от 250мм до 295мм. Полотно выполнено из инструментальной хром-марганцевой высоколегированной стали и закалено до твердости 60HRc. Рукоять выполнена из древесины граба, размер ручки - 130x30мм и 135х30мм. Рукоять без покрытия - мастер сам выбирает покрытие. Рукоять в месте соединения с полотном укреплена латунным кольцом с кожаной прокладкой. Также имеются наборы стамесок в сумке скрутке. Производство - Европа.

Designed for grinding steel parts. Used for grinding and polishing metals and minerals.
Vulcanite polishing wheel with rubber base with abrasive grit. The mineral is volcanite. The binder contains rubber. Because of this, vulcanite polishing wheels are also called rubber.
The diameter of the circle is 150mm, the width of the circle is 16mm. Landing hole 32mm. Gritness - 180.

Vulcanite block made on a rubber base: vulcanized synthetic rubber, abrasive material and special additives. Its main function is minimization of burns and burrs during material processing, high-quality grinding and polishing, sharpening of cutting tools and metal cutting.

Designed exclusively for high-quality grinding of metal and its subsequent polishing. When grinding metal with the help of vulcanite, it is possible to remove hundredths of a millimeter from its surface. This type of abrasive is successfully used for sharpening Rechitsa chisels, knives, axes and other cutting tools. In addition, vulcanite abrasives do not require the restoration of the top layer, it does not get greasy.

Polishing with a vulcanite wheel is carried out after the final shaping of the workpiece. When processing metal, the optimal number of revolutions is considered to be 2500-3000. After processing the part with vulcanite, you can make an additional refinement with a felt wheel with a pre-applied polishing paste.

Circles of the required profiles are easily made from the bar.

Нож раскроечный ПЕТРОГРАДЪ, модель 2, правая заточка, в чехле. Можно использовать для прямолинейного реза и торцевания кожи. Нож укомплектован кожаным чехлом.
Нож имеет 2 режущие стороны. Верхние и нижние режущие кромки заточены и доведены до бритвенного состояния. Нож не требует доводки и готов к работе. 

Выполнены из инструментальной стали и закалены до твёрдости 58-61HRC.

Произведено в России на фабрике «ПЕТРОГРАДЪ

 

The saddle knife is designed for cutting and roughing leather. Can be used for straight cuts and trimming of leather. Semicircular wide blade with one-sided right sharpening. RK length 65mm. Blade width - 30 mm, length - 70-75mm, thickness 1.7mm. The total length of the knife is 180mm. The grips are made of maple, covered with oil. Handle length 105mm. The blade is made of 9HF carbon steel, hardened to a hardness of 57-61HRc. The PETROGRAD tool is sharpened and ready to work. Equipped with leather covers.
Supplied with covers to protect the cutting edge and against accidental cuts on the hands.
Production of the PETROGRAD factory.

Тиски столярные вертикальные, ширина подвижной губки 120мм. Переставные вертикальные верстачные тиски позволяют расширить функциональность верстака. Расстояние от верха верстачной доски до винта тисков составляет 240мм. Тиски изготовлены на основе  металлической винтовой пары. Фиксируются тиски от продольного перемещения комплектным упором диаметром 19мм. Для этого необходимо совместить вертикальное отверстие в тисках с отверстие м в верстачной доске и установить упор. Для выставления диапазона зажима в нижней направляющей тисков предусмотрены отверстия для ограничения хода в которые устанавливается упора диаметром 19мм. Устанавливаются на верстаки Рубанков.

Carving knives with a straight butt and a curved cutting edge are great for power work. The knife is an analogue of the famous carving knife "Carving Sloyd knife". Blade length 60mm. Comfortable oval handle made of precious wood and coated with oil. Handle length - 115mm. Great knife for beginners and professionals alike. The 2mm thick blade is made of high carbon steel hardened to a hardness of 59-61 HRc. This set is packed in a gift box made of beech, the lower part has a lodgment, which is suitable for models of Petrograd carving knives. This is an elegant way to present a carving knife from the Petrograd tool line as a gift. The box is made of beech, on a CNC machine and decorated with a brand and covered with oil. Production of the Petrograd factory (Russia).
To select the desired knife, click on the product name

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

Abrasive water stones. Grit: 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.

Water stone. 360 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

 

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

The model range is represented by straight chisels with an expanding blade with a working part width of 8 mm, 10 mm, 12 mm. They have a wide range of applications for both carving and woodworking such as fitting joints on dovetail. Chisels are made of steel 65G (Germany 66Mn4, Ck67, USA 1066) and have beech handles coated with tung oil. Blade length - 35 mm, total length - 180 mm, sharpening angle - 30 degrees, blade thickness - 2 mm. 

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 15х15х120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

> Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

Water stone. 2000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.

High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.

Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.

Comparison of FEPA, JIS and GOST standards:

Marking knives  PETROGRAD have a swept blade that is sharpened on 2 faces, which makes it comfortable to use both right-handed and left-handed. One-sided sharpening. The 2.3mm thick blade is made of high carbon steel and hardened to 61HRC. The handle is made of curly maple and saturated with linseed oil. Before the blade on the handle made a comfortable stop to prevent sliding of the hand. The length of the handle is 160mm.Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia

Push sticks PETROGRAD are used to safely push workpieces on router tables, format-cutting and cabinet saws, and so. The shape of the handle has a special stop to prevent the hand from sliding. Available in 2 lengths - 320mm and 440mm. Thickness - 20mm, made of beech. Coating - tung oil.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.