Categories
Plane blade, PETROGRAD, 50mm*175mm
The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 50 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Plane blade, PETROGRAD, 60mm*175mm
The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 60 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Stanley standart plane blade, PETROGRAD, 51mm * 3.2mm
Replacement blades for Stanley, Dictum and similar planers are designed to replace a worn blade or expand the capabilities of your tool. They allow replacing native knives on Stanley / Dictum planers, 4, semi-jointing planes 5.
The piece of iron is made of steel 9XC. Hardened to 59-61 HRC. Knife length - 175 mm, width 50mm, minimum thickness 3.5mm.
Knives have two sides - one hard, one soft (production feature)
Each knife is tested with a hardness tester.
The hard side has 2 points from the diamond cone - test, and control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without impairing the working qualities of the tool.
Knives for wooden planers are made at the factory of joinery and carpentry tools PETROGRAD
Production - Russia
Stanley standart plane blade, PETROGRAD, 51mm * 2.5mm
Replacement blades for Stanley, Record and similar planers are designed to replace a worn blade or expand the capabilities of your tool. They allow replacing native knives on Stanley / Record planers, 4, semi-jointing planes 5.
The piece of iron is made of steel 9XC. Hardened to 59-61 HRC. Knife length - 175 mm, width 50 mm, minimum thickness 2.5 mm.
Each knife is tested with a hardness tester.
The hard side has 2 points from the diamond cone - test, and control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without impairing the working qualities of the tool.
Knives for wooden planers are made at the factory of joinery and carpentry tools PETROGRAD
Production - Russia
Scrub plane blade, PETROGRAD, 30mm*175mm
The scrub plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 30 mm, thickness minimum 2.2 mm, thickness maximum 3.5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Blank blade for moulding plane, `strip`, w/o sharpening, 10mm*180mm
The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| item | item code | shank width mm | minimum shank thickness mm | flag length mm | flag width mm | flag max thickness mm | overall length mm |
| Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm | М00014997 | 10 | 3,2 | - | 10 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm | М00015123 | 10 | 3,2 | 40 | 16 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm | М00014666 | 10 | 3,2 | 40 | 20 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm | М00014590 | 10 | 3,2 | 40 | 24 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm | М00014667 | 10 | 3,2 | 40 | 30 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm | М00015124 | 10 | 3,2 | 40 | 36 | 4,6 | 180 |
Blank blade for moulding plane, `flag`, w/o sharpening, 24mm*180mm
The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| item | item code | shank width mm | minimum shank thickness mm | flag length mm | flag width mm | flag max thickness mm | overall length mm |
| Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm | М00014997 | 10 | 3,2 | - | 10 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm | М00015123 | 10 | 3,2 | 40 | 16 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm | М00014666 | 10 | 3,2 | 40 | 20 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm | М00014590 | 10 | 3,2 | 40 | 24 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm | М00014667 | 10 | 3,2 | 40 | 30 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm | М00015124 | 10 | 3,2 | 40 | 36 | 4,6 | 180 |
Blank blade for moulding plane, `flag`, w/o sharpening, 36mm*180mm
The blank is made of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blade have two sides - one hard, one soft (production feature)
Absolutely every knife is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| item | item code | shank width mm | minimum shank thickness mm | flag length mm | flag width mm | flag max thickness mm | overall length mm |
| Blank blade for moulding plane, "strip", w/o sharpening, 10mm*180mm | М00014997 | 10 | 3,2 | - | 10 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 16mm*180mm | М00015123 | 10 | 3,2 | 40 | 16 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 20mm*180mm | М00014666 | 10 | 3,2 | 40 | 20 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 24mm*180mm | М00014590 | 10 | 3,2 | 40 | 24 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 30mm*180mm | М00014667 | 10 | 3,2 | 40 | 30 | 4,6 | 180 |
| Blank blade for moulding plane, "flag", w/o sharpening, 36mm*180mm | М00015124 | 10 | 3,2 | 40 | 36 | 4,6 | 180 |
Нож для "косого" зензубеля ПЕТРОГРАДЪ
Нож для "косого" зензубеля ПЕТРОГРАДЪ. Предназначен для установки в деревянный зензубель Петроградъ. Выполнен из стали 9ХС. Закален до 60-61 HRc. Заточен "из коробки" до 1000 грит. Угол заточки составляет 30 градусов. Производство – фабрика Петроградъ (Россия).
Petrograd Plane Blade 150mm*50mm*2.2mm, 25 degree, without slot
Нож для одинарного рубанка, ПЕТРОГРАДЪ, 150мм*50мм*2,2мм, 25 градусов. Нож для одинарного рубанка, выпускаемого Сестрорецким Инструментальным заводом имени Воскова. Подходит также для одинарных рубанков, произведённых в своё время и другими советскими заводами. Производство – фабрика Петроградъ (Россия).
Zelland spare blade, 34mm*105mm
Нож для рубанка Zelland, 34мм*105мм, прямая РК, фаска 25 градусов, клеймо ПЕТРОГРАДЪ. Выполнен из стали 9ХС, закален до 60-61 HRc. Производство – фабрика Петроградъ (Россия).
Zelland spare blade, 55mm*120mm, tooth edge
Нож для рубанка Zelland, 55мм*120мм, зубчатая РК. Этот нож обладает долотообразными зубчиками шириной 0,9 мм. Он предназначен для работы по сложным породам древесины. Устанавливается в рубанки Zelland. Производство – фабрика Петроградъ (Россия).
Zelland spare blade, 55mm*120mm
Нож для рубанка Zelland н13, 54мм. Выкован из стали 9ХС и закален до 60 единиц по шкале Роквелла. Нож имеет заводскую заточку в 20 градусов. Производство Zelland (Россия).
Zelland spare blade, 55mm*120mm
Нож для рубанка Zelland н13, 54мм. Выкован из стали 9ХС и закален до 60 единиц по шкале Роквелла. Нож имеет заводскую заточку в 25 градусов. Производство Zelland (Россия).
Plane blade, PETROGRAD, 30mm*110mm
The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 80 mm, width 30 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Plane blade, PETROGRAD, 40mm*175mm
The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 175 mm, width 40 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Plane blade, PETROGRAD, 50mm*175mm, thickness 3.5-2.5mm
Plane blade, PETROGRAD, 65mm*175mm
The blade for wooden planes. Ьade of steel 9HS (DIN - 150Cr14), hardened to 59-61 HRC. It has dimensions: total length 175 mm, width 65 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes from others, and is ideal for wooden planes with wedge fixation.
Blades have two sides - one hard, one soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Stanley standart plane blade, PETROGRAD, 51mm * 3.2mm, Scrubplane's type
Ножи для рубанка, стандарт Stanley/Dictum, толщина 3.2 мм, выполнен из легированной стали. Запасные ножи для рубанков Stanley, Dictum и похожей конструкции (не подходит для некоторых моделей Stanley и Восковского завода, для них есть модель с толщиной 2.5мм). Предназначены для замены изношенного ножа или расширения возможностей вашего инструмента. Позволяют заменить родные ножи на выглаживающих рубанках Dictum/Luban номер 4 и полуфуганках (номер 5). Производство фабрика Петроградъ (Россия).
Stanley standart plane blade, PETROGRAD, 60mm * 3.2mm
Нож для рубанка, стандарт Stanley/Dictum, 60мм, толщина 3.2мм предназначен для Stanley, Dictum и похожей конструкции. Используются для замены изношенного ножа или расширения возможностей вашего инструмента. Позволяют заменить родные ножи на выглаживающих рубанках Dictum номер 4 1/2. Производство фабрика Петроградъ (Россия).
Ножи для рубанков
Все железки (рубаночные ножи) производятся на фабрике Петроградъ, имеют клиновидный спуск с углом 0,5 градуса. Это выгодно отличает их от других рубаночных ножей, и делает их идеально подходящими для деревянных рубанков с клиновой фиксацией ножа.
Рабочая сторона ножа, закалённая до твёрдости 59-61HRc, помечена небольшими отверстиями, остающимися от проверки ножа твёрдомером. Эти отверстия, имеющиеся на каждом ноже, являются свидетельством проверки ножей и не влияют на работоспособность изделия.
Ассортимент ножей для ручных рубанков Петроградъ постоянно пополняется и насчитывает на сегодня: 17 ножей различных моделей и размеров, начиная от ножей для классических выглаживающих рубанков и заканчивая экзотикой типа ножей для грунтубелей, фальцгобелей и рубанков калевочного типа.
Приобретая рубаночный нож от фабрики Петроградъ в покупаете качественную и надежную вещь которая будет служить и радовать вас годами.
Popular goods
Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete N2-18, 60°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-18, 60°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 60°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving set PETROGRAD, N5
The set N5 includes:
- Carving knife PETROGRAD, Swedish type, 175mm/60mm
- Carving knife PETROGRAD, skew 40 deg, 165mm/35mm
- Spoon knife ( hook knife ) model N1, D 27mm, right one
- Sharpening stone PETROGRAD, 120*15*15mm, 1500 grit
- Textile 4 pocket Tool Roll, PETROGRAD, 360*200mm
Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit
Water stone. 2000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
Comparison of FEPA, JIS and GOST standards:
Apron RUBANKOV, model 4, light-brown
Фартук Столярный Rubankov кожаный, светло-коричневый. Длина фартука - 800 мм, ширина - 680 мм. Нагрудный карман c 1 отделением. Размеры нагрудного кармана - длина 150 мм, ширина 175 мм. Лямки и поясной ремень оборудованы застежками и пряжками. Цвет фартука - светло-коричневый. На фартук нанесен логотип Rubankov. Материал - 100 % натуральная кожа, металлическая фурнитура.
Сделано в России.