Wooden apron plane PETROGRAD, 30mm/150mm



Rating : (2)
Shipping: worldwide

8000 p (123.04)

Description

Traditional wooden small plane, the so-called "apron hand plane". This small hand plane uses for various types of work, it is always at hand, fit in the pocket of your clothes or apron.

  • body of hand plane is made of hornbeam
  • wedge made of mahogany
  • hand plane dimensions: 150x45x69 mm
  • coating - oil and wax

Blade installed in hand plane body with 45 degrees angle and fixed by wooden wedge.

  • blade was made of alloyed tool steel 9XC (DIN - 150Cr14)
  • hardned to 59-61 HRC.
  • blade length - 79 mm
  • blade width - 30 mm
  • blade shape - wedge
  • blade thickness minimum 4.8 mm
  • maximum thickness - 5.2 mm.
  • sharpening edge is 30 °

All PETROGRAD hand plane blades have a wedge-shaped descent with an angle of 0.5 degrees. This distinguishes them favorably from other plane blades, and makes them ideal for wooden planes with a wedge fixation. The working side of the knife, hardened to a hardness of 59-61 HRc, is marked with small indentations, which remain from the hardness gauge after checking the knife. These recesses, which are located on each blade, are evidence of checking blades and do not affect the performance of the product.

IMPORTANT! The reverse side of the knife, not marked with control points, is not working!
The manufacturer reserves the right to change the thickness of the knife without degrading the working qualities of the tool.

Hand made by Petrograd toolworks in Saint Petersburg Russia.


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

Wooden fore plane PETROGRAD, 455mm/60mm

Traditional wooden jointer. The plane is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam, the handle is made of paduk. Coating - tung oil. The wedge is also made of maple. The installation angle of the knife is 50 ° -55 °. The blade is made of alloyed tool steel 9XC (DIN - 150Cr14) hardened to 59-61 HRC. Blade dimensions: length - 175 mm, width - 60 mm, knife thickness minimum 2.2 mm, maximum thickness - 3.5 mm. Sharpening angle 30 °. Dimensions of jointer plane 455 * 80 * 170 mm.

All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.

16000p(123.04)
Отзывов: 1
>Рейтинг:

Wooden plane PETROGRAD, Gerfschaaf type

Рубанок деревянный ПЕТРОГРАДЪ, 165мм / 30мм, голландский тип (Gerfschaaf) это классический "фартучный" рубанок, основным предназначением которого издревле была работа за пределами мастерской. Образцом для создания рубанка голландского типа стал рубанок, известный под названием Gerfschaaf и хранящийся В Музее-Мастерской Рубанков. Производство фабрика Петроградъ (Россия).

8000p(123.04)
Отзывов: 1
>Рейтинг:

Carpenter drawknife PETROGRAD N5, Swedish type, 270mm

The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

7200p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 270mm

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

5300p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2060p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Finnish type, 175mm/45mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Sharpening set PETROGRAD N1, for woodworking tools, 3 stones

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

7460p
Отзывов: 1
Рейтинг:

Natural lapping stone PETROGRAD, 200*70*20mm

Lapping stone from gabbro diabase. Used for lapping the soles of planes, abrasive stones and other surfaces. It has a perfectly smooth surface. Lapping is carried out with abrasive powders or diamond pastes. Approximate dimensions: 200x70x20 mm. Made in Russia.

2400p
Отзывов: 1
Рейтинг:
new

Froe PETROGRAD, model Uglich 300мм

Froe is a special cleaving axe (cleaver) for green woodworking, bodging and spoon making. Long blade and perpendicularly handle make it easy to split wood along the grain. Thick blade back would be good to use with mallet or even log*. Froe axe also good for split logs for fireplace, stove or even for making wood shingles and wooden blanks for spoons.

Edge is lenticular sharpened. Froe "Uglich" by petrograd toolworks is perfect choice for making blanks for spoon making. Froe axe is hand forged and totally made in Saint-Petersburg Russia

8000p
Отзывов: 1
Рейтинг:

The book `Practical course of woodworking art` + Atlas of drawings, M. Netyksa

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

2200p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

3440p
Отзывов: 1
Рейтинг: