Categories
Description
Упоры верстачные, ПЕТРОГРАДЪ, латунь, D18мм*115мм, 2 штуки. Эти круглые верстачные упоры сделаны из прутков твердой латуни и легко устанавливаются в стол или верстак с отверстием 19 мм. Являются аналогом латунных упоров Veritas. Производство фабрика Петроградъ (Россия).
Характеристика упоров:
- Материал: латунь
- Длина: 115 мм
- Диаметр: 18 мм
- На упорной части нанесен штрих
- Наклон упорной части 2 градуса
- В комплекте 2 шт
С одного конца упоров имеется плоская часть с нанесенным штрихом и внутренним наклоном в 2 градуса, что позволяет прочно, без проскальзывания зажимать заготовки. Гладкая поверхность упоров позволяет легко устанавливать их в отверстие, а имеющаяся стальная пружина не дает им проваливаться в верстачные отверстия. Длина упоров 115 мм. В комплекте 2 шт. Производство фабрика Петроградъ (Россия).
*Пружина в первой партии упоров может немного деформироваться при полном погружении упора в верстак.
Are you sure?
Find out a mismatch? Highlight text and press Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
Beech bench dog, 4 ps
These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia
Popular goods
Carving axe PETROGRAD, model Zvenigorod 7, handle n5
Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.
- Blade width 120 mm
- Sharpening angle - 25 degrees
- Hardness - 55-58HRc
- Handle lenght - 350 mm
- Full weight - 07 kg
Carving axe Zvenigorod VII is quite small and easy to control. It's weight is about 650g, makes it maneuverable and allows you to work more accurate and precise.
The shape of the axe head was designed for carving operations where palm is resting extreamly close to axe head or even on the axe head. This design helps to exelent control of the axe even during long carving sessions. Grip above the head is used for trimming, stripping. This axe model was based on samples from museum "Rubankov" and finalized taking into account the wishes of wood carvers.
The axe head is hand forged from steel 65Г (spring steel) and hardened to 55 - 58 HRc at the cutting edge and along the entire beard, the rest part is normalized to HB280. This hardening allows you to hit the poll without the risk of creating a cracks in the metal.
Head has mounted to handle on 3 wedges, one along the head eye and two in cross section.
Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.
Axe handle is made of maple* and coated with Danish oil**. The hatchet handle has a longitudinal bend. In cross-section the handle has the shape of an egg, which is very convenient for good grip while carving. Handle has a hole for hanging.
Woodcarving axe Zvenigorod VII are product of Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.
Sharpening stone PETROGRAD, 200*70*20mm, 360 grit
Abrasive water stones. Grit: 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 200*70*20mm, 120 grit
Abrasive water stones. Grit: 120, 150, 360, 500, 800, 1000,1500, 2000 and 4000 grit. Size 200x70x20mm. The abrasive grain is silicon carbide. Bond - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Axe Anika, model Tomohawk
Bevel edge chisel, PETROGRAD, model Volga, 26mm
Bevel edge chisel Volga. These chisels have a classic design with blades that are bevel-edged to a narrow land on each side, providing excellent clearance when trimming into an angled corner such as in dovetail work, as well as reducing sidewall friction when working in a tight recess.
- blade lenght - 150 mm
- blade width - 26 mm
- blade is made of high-alloyed chrome-manganese steel
- hardened to 59-61 HRc
- basic edge angle - 25 degrees
Chisels are made focusing on the experience of old masters of woodworking. Comfortable handle. The handle at the junction with the blade reinforced brass ring.
- handle lenght - 130 mm
- overall length - 280 mm
Made by Petrograd toolworks in Saint Petersburg Russia.
| Weight: | 0.22 kg |
|---|---|
| Type: | bevel edge |
| Steel: | 9ХС |
| Hardness: | 59-61HRc |
| Handle material: | Ash* |
| Handle lenght: | 130 mm |
| Edge: | straight |
| Sharpening angle: | 25 degrees |
| Blade lenght: | 150 mm |
| Blade width: | 26 mm |
| Total lenght: | 280 mm |
* material of handles may changes from batch to batch.
** coating oil may changes too
