Categories
Sharpening stone PETROGRAD, 153*15*15mm, 800 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 360 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 1000 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 2000 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 4000 grit
Абразивные водные камни. Зернистость: 150, 360, 500, 800, 1000,1500 и 2000. Размер 15х15х153мм. Абразивное зерно - карбид кремния. Связка - керамика. Твёрдость I обеспечивает минимальный износ камня при работе. При заточке не перегревается сталь. Не требует использования масла. Перед использованием замочить в воде на 2-10 мин. Предназначен для заточки сталей и твердых сплавов. Производство - сделано в России.
Sharpening stone PETROGRAD, 153*15*15mm, 1500 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 500 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Sharpening stone PETROGRAD, 153*15*15mm, 150 grit
Sharpening stone PETROGRAD. Granularity: 150, 360, 500, 800, 1000, 1500 and 2000. Size 15x15x153mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. When sharpening, the steel does not overheat. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Manufactured in Russia.
Box for Sharpening set Petrograd, n4
Деревянный ящик для хранения заточных брусков ПЕТРОГРАДЪ. Очень удобен для хранения абразивных камней ПЕТРОГРАДЪ квадратных и особенно круглых. Габаритные размеры 162х134х30мм (ДхШхВ). Абразивные камни в комплект не входят.
Производство Россия.
Dressing stone PETROGRAD, 120*15*15mm, 4000 grit
Abrasive water stones. Granularity: 150, 360, 500, 1000, 1500 and 2000, 4000. Size 15x15x120mm. The abrasive grain is silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during work. Steel does not overheat when sharpening. Does not require oil. Soak in water for 2-10 minutes before use. Used for sharpening and beveling.
High productivity of sharpening, second only to diamond, is provided by the use of abrasive grains of silicon carbide, which are distinguished by sharpness and brittleness. The high hardness of silicon carbide abrasives allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of alumina powders. In addition to productivity, it is worth noting the extraordinary tactile sensations when sharpening the tool. The stones quickly slurry and produce a very pleasant sound.
PETROGRAD water stones are characterized by high performance and geometry as delivered.
In the characteristics of the water stone are indicated: the first letter - hardness (I, J - soft, K - medium); grain size according to the Japanese standard JIS R6001-1987 - 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and the material is silicon carbide (C- green, B- the black). Comparison of FEPA, JIS and GOST standards:
Заточной абразив ПЕТРОГРАДЪ, 125*25*6мм, 1000грит
Заточной абразив ПЕТРОГРАДЪ, 125*25*6мм, 1000грит. Средне мягкой твердости, используются для заточки инструмента. Абразивное зерно – карбид кремния. Производство фабрика Петроградъ (Россия).
Petrograd axe sharpening stone 500 grit
Заточной абразив ПЕТРОГРАДЪ, 125*25*6мм, 2000грит
Заточной абразив ПЕТРОГРАДЪ, 125*25*6мм, 2000грит. Средне мягкой твердости, используются для заточки инструмента. Абразивное зерно – карбид кремния. Производство фабрика Петроградъ (Россия).
Ножевые абразивы
Popular goods
Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving knife PETROGRAD, Bogorodsky type, 200mm/60mm
Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete B-2
Checkering too B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete C-1, 60°
Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.
Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Checkering tool complete N2-18, 60°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
| Item code | Item | Cutting angle |
Teeth per inch |
| М00015687 | N2-16 | 60° | 16 |
| М00015638 | N2-16 | 90° | 16 |
| М00015688 | N2-18 | 60° | 18 |
| М00015669 | N2-18 | 90° | 18 |
| М00015689 | N2-20 | 60° | 20 |
| М00015662 | N2-20 | 90° | 20 |
| М00015690 | N2-22 | 60° | 22 |
| М00015637 | N2-22 | 90° | 22 |
| М00015691 | N2-24 | 60° | 24 |
| М00015676 | N2-24 | 90° | 24 |
Checkering tool complete N3-18, 60°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 60°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 60 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 60 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving set PETROGRAD, N5
The set N5 includes:
- Carving knife PETROGRAD, Swedish type, 175mm/60mm
- Carving knife PETROGRAD, skew 40 deg, 165mm/35mm
- Spoon knife ( hook knife ) model N1, D 27mm, right one
- Sharpening stone PETROGRAD, 120*15*15mm, 1500 grit
- Textile 4 pocket Tool Roll, PETROGRAD, 360*200mm
Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit
Water stone. 2000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Used for sharpening and setting bevels.
High sharpening performance, second only to diamond, is ensured by the use of silicon carbide abrasive grains, which are notable for their sharpness and brittleness. The high hardness of carbide-silicon grinding materials allows you to confidently process not only carbon steels, but also hard alloys, which is impossible on stones made of electro-alumina powders. In addition to performance, it is worth noting the extraordinary tactile sensations when sharpening a tool. Stones quickly give a slurry and produce a very pleasant sound.
Water stones PETROGRAD are distinguished by high performance and geometry in a state of delivery.
In the characteristic of a water stone are specified: the first letter - hardness (I, J - soft, K - average); Japanese grain size according to JIS R6001-1987 is 150 (80 microns), 360 (34 microns), 500 (24 microns), 1000 (12 microns), 2000 (6 microns) and C is silicon carbide.
Comparison of FEPA, JIS and GOST standards:
Apron RUBANKOV, model 4, light-brown
Фартук Столярный Rubankov кожаный, светло-коричневый. Длина фартука - 800 мм, ширина - 680 мм. Нагрудный карман c 1 отделением. Размеры нагрудного кармана - длина 150 мм, ширина 175 мм. Лямки и поясной ремень оборудованы застежками и пряжками. Цвет фартука - светло-коричневый. На фартук нанесен логотип Rubankov. Материал - 100 % натуральная кожа, металлическая фурнитура.
Сделано в России.