Checkering set, type N1, 90/18lines, 6 tools



Rating : (1)
Shipping: worldwide

7580 p (116.58)

Description

Checkering tool Set N1 (90 degrees, 18 lines) includes 6 tools  for making checkers on wood. Gouges by Petrograd toolsworks for making checkers. Set of tools with 90 degree cutters, this type is making more sharp checkers that grants great grip and less prone to clogging than flat ones.

Set number 1 includes:

  • gouge B-2 ( two cutting edges, spacer with tooths )
  • gouge S-1 ( one cutting edge )
  • gouge N2-18, 90 ( two cutting edges )
  • gouge N3-18, 90 ( right router, left cutting edges )
  • gouge N4-18, 90 ( left router, right cutting edges )
  • gouge C-1, 90 ( one cutting edge )
  • roll bag for carving tools ( 6 pockets )
  • Checkering gauge
Gouges for making checkers. Checkering is a type of woodcarving and decorating handles of knives, rifles. This gouges was based on our expirience of use the variety of worldwide know gouges. Model line includes all base gouges from 16 to 32 lines per inch with angles about 60 and 90 dergrees. All gouges blades can be replaced on new ones and can be purchased separately.

Checkering tool set by Petrograd toolworks. Made in Saint-Petersburg Russia.

Number of tools:6 tools
Type of checkers:90 degrees
Number of lines:18 lines on 1 inch
Handle material:Beech*
Handle lenght:120 mm
Total lenght:240 mm
Total weight:0.3 kg

1. Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90

2. Checkering tool N2-18. Both sides with 18 teeth per inch. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

3. Checkering tool B-2, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained. Maximum roller height 1 mm, width 2.5 mm

4. Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with 18 teeth per inch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.

5. Checkering tools from series N4 have two sides: the right side with 18 teeth per inch, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle

6. Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work. It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters. The wooden handle is made of beech, well balanced and lies comfortably in your hand. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods. The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained. The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees

Totally hand made by PETROGRAD-TOOLS factory of joinery and carpentry tools. Made in Russia.


Share / Save Link:

Videos

youtube video
youtube video
youtube video

Specs

Reviews

Instructions ()

Publications

Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 170mm

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 170 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

4700p
: 1
:

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1400p
: 1
:

Carving knife PETROGRAD, Swedish type, 170mm/40mm

Carving knives with a straight butt and a curved cutting edge are great for strength work. Blade length 45mm or 60mm. The length of the handle - 115mm. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
1400p
: 1
:

Sharpening set PETROGRAD N3, for knives, 3 stones

Water stones. Grain size: 150, 360, 500, 1000, 1500 and 2000. Size 1515120mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

 

1290p
: 1
:

Center finding dowel/tenon pin set PETROGRAD, D6 mm, 6 pcs

Centerfinding pins for furniture dowels. Diameter of punch: 5 mm, 6 mm, 8 mm, 10 mm, 12 mm.Totally hand made atPETROGRAD factory of joinery and carpentry tools.Made in Russia.

460p
: 1
:

Mallet PETROGRAD, `barrel`, D85mm, 600 g

Mallet PETROGRAD, "barrel", striker size - mm D85
Excellent all-wooden mall weighing 500 g (+ -30 g)
The mallet is made of beech and covered with tung oil. The mallet has a barrel shape and a comfortable, chiseled, ergonomic handle. The handle is fixed on a wooden wedge. Mallets are widely used when working with bits and chisel chisels when cutting connections, as well as when carving large items or sculptures.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

1100p
: 1
:

Outdoor axe PETROGRAD, model Roslavl VII, straight handle

Outdoor axe. Overall length - 370 mm. Axe height - 140 mm. The length of the cutting edge - 115 mm. The axe is forged by hand from 65G steel (Germany 66Mn4, Ck67, USA 1066). Sharpening straight. Total weight - 0.7 kg. Comes with a leather case to protect the blade. The axe handle is made of maple wood, 320 mm long. The axe is perfectly balanced and is suitable for a wide variety of works, like a hiking axe, for small carpentry and carpentry works, and simply as a universal axe.

Totally hand made atPETROGRAD factory of joinery and carpentry tools.Made in Russia.

8500p
: 1
:

Carving axe PETROGRAD, model Zvenigorod VII

Wood carving axe Zvenigorod VII . This axe is made for artistic processing of wood, such as carving sculptures, bowl carving, dish carving and other stuff.

  • Blade width 120 mm
  • Sharpening angle - 25 degrees
  • Hardness - 55-58HRc
  • Handle lenght - 350 mm
  • Full weight - 07 kg

Carving axe Zvenigorod VII is quite small and easy to control. It's weight is about 650g, makes it maneuverable and allows you to work more accurate and precise.

The shape of the axe head was designed for carving operations where palm is resting extreamly close to axe head or even on the axe head. This design helps to exelent control of the axe even during long carving sessions. Grip above the head is used for trimming, stripping. This axe model was based on samples from museum "Rubankov" and finalized taking into account the wishes of wood carvers.

The axe head is hand forged from steel 65 (spring steel) and hardened to 55 - 58 HRc at the cutting edge and along the entire beard, the rest part is normalized to HB280. This hardening allows you to hit the poll without the risk of creating a cracks in the metal.
Head has mounted to handle on 3 wedges, one along the head eye and two in cross section.

Cutting edge is razor sharp and ready to work out of the box. Sharpening angle - 30 degrees.

Axe handle is made of maple* and coated with Danish oil**. The hatchet handle has a longitudinal bend. In cross-section the handle has the shape of an egg, which is very convenient for good grip while carving. Handle has a hole for hanging.

Woodcarving axe Zvenigorod VII are product of Petrograd toolworks and supplied in a leather case for protection of the cutting edge and easy storage. Made in Saint-Petersburg Russia.

9200p
: 1
:

Leather Knife PETROGRAD, type 2, double bevel

Knives saddlery PETROGRAD.
The saddlery knife is designed for cutting and grinding leather. It can be used for straight cutting and skin cutting. The knife is equipped with a leather case.

4700p
: 1
: