PETROGRAD Workbench's hardware kit N2



Rating : (1)
Shipping: worldwide

2600 p (39.99) out of stock

Description

Finishing oil PETROGRAD for workbenches and tool handles, 0.5l. Primer, used to apply the first coat before finishing. Recommended for use on hard or absorbent wood. Recommended for workbenches, tables, handles, woodworking tools and other woodworking parts. For indoor use only. It quickly and deeply penetrates the material and also quickly polymerizes.
Composition:
Tung oil, linseed oil, modified oils (linseed, tung, safflower, walnut), ricin oil, carnauba wax, micronized wax.
Mode of application:
Apply oil evenly to the prepared surface free of dirt and grease using a brush or lint-free cloth. After 10 minutes, wipe off the remaining oil from the surface with a dry, lint-free cloth. After 8 hours (depending on layer thickness and ambient temperature) apply a second coat. Ensure good ventilation of the room, both during application and at the end of work.
Note:
Certain oily, exotic or brightly colored woods and excessive amounts can prevent the oil from drying or greatly slow down the drying process. In this case, good ventilation is needed to speed it up.
- Do not use nitrile gloves for work.
- Safe for hands
- Always wear protective goggles when working.
Storage:
In a sealed container. It should be kept away from sources of fire and sparks.


These round bench rests are made from solid beech and easily fit into a table or workbench with a 19 mm hole. The smooth surface of the stops makes them easy to fit into the hole. Stop length 50 mm, head: Ø 30 mm, height 15 mm, body: Ø 18.5-18.8 mm, height 35 mm. Includes 4 pcs.

 

Fan gasket for bench press. Size 40x120 mm consists of 7 slats (4,5,5,5,5,5,10 mm). This simple device is designed to help prevent the vise from skewing and jamming by clamping the workpiece to one side of the vise. Just fit as many fan-shaped spacers as you need so that the thickness of the fan-shaped insert is approximately the same as the thickness of your part. When clamping parts with a thickness of more than 40 mm, it is recommended to use junk pieces of wood together with the fan to compensate for the skew. This keeps your workpiece securely in place and prevents the vise mechanism from skewing and jamming. The gaskets are made of various types of wood and have an aesthetic appearance.

Production - factory of joinery and carpentry tools PETROGRAD.

Made in Russia


Share / Save Link:

Specs

Reviews

Instructions ()

Нет файлов

Publications

Recommended products

%

Volcanite disc 150mm*40mm*32mm, 60grit

Designed for grinding steel parts. Used for grinding and polishing metals and minerals.
Vulcanite polishing wheel with rubber base with abrasive grit. The mineral is volcanite. The binder contains rubber. Because of this, vulcanite polishing wheels are also called rubber.
The diameter of the circle is 150mm, the width of the circle is 40mm. Landing hole 32mm. Gritness - 60.

1500p(39.99)
Отзывов: 1
>Рейтинг:

Marking knife PETROGRAD, model N3, flexible, arrow form

Dovetail Marking knife N3 has flexible blade with arrow form. This knife is a carpentry tool for precision marking, it has one-sided sharpening. Blade of marking tool is made of high carbon steel and hardened. Best for marking dovetail joints. Arrow form give easy two side marking: forward and backwark.

Knife blade was sharpened and ready to work out of the box.

  • high carbon steel ( like 60SG2A steel (Germany 66Mn4, Ck67, USA 1066))
  • hardened to 59-61 HRc
  • blade length - 40 mm
  • blade width - 9 mm
  • blade thickness - 0.73 mm
  • sharpening angle - 30 degrees
  • skew angle - 60 degrees
1200p(39.99)
Отзывов: 1
>Рейтинг:

Carpenter drawknife PETROGRAD N5, Swedish type, 270mm

The forged drawknife bent in two directions has an advantage over other non-linear drawknives in convenience and control. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The total length of the drawknife is 650 mm. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding. Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

7200p
Отзывов: 1
Рейтинг:

Carpenter drawknife PETROGRAD N11, u-shaped, with raised arms, 270mm

A flat drawknife with curved and perpendicular cutting edge with handles will be convenient for various operations both in woodworking and carpentry: precise fit of logs in size, manufacture of seats, quick material removal in joinery, etc. Handles are raised above the blade plane and allow work closely to the treated surface. The blade is forged manually from tool steel 65G (Germany 66Mn4, Ck67, USA 1066) and hardened to 55-58 HRC. Sharpening - chamfering up. Handles 140 mm long are made of beech and impregnated with oil. Blade length - 270 mm, width 36 mm. Blade thickness - 6 mm, sharpening angle - 30 degrees. Comes in a leather case with a clasp on the buttons. The design of the drawknives, as well as their sharpening, is recommended by the Russian Carpenters Union for debarking and carpentry work on fitting logs. Other kinds of carpentry work may require regrinding.Blade was fully hardened through, that allows you to repeatedly honing the blade or his fully re-grind it. Totally hand made at PETROGRAD factory of joinery and carpentry tools.

Made in Russia.

5300p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 800 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

2060p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Bogorodsky type, 170mm/40mm

Carving knives for general use, as well as for large material removal. Blade length 40mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to 59-61 HRc. All the knives are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Carving knife PETROGRAD, Finnish type, 175mm/45mm

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
 
2400p
Отзывов: 1
Рейтинг:

Sharpening set PETROGRAD N1, for woodworking tools, 3 stones

Water stones. Grain size: 150, 360, 500, 800, 1000, 1500 and 2000. Size 200x70x20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

To select and order an abrasive stone of desired grain size, click on the name of the product.

7460p
Отзывов: 1
Рейтинг:

Natural lapping stone PETROGRAD, 200*70*20mm

Lapping stone from gabbro diabase. Used for lapping the soles of planes, abrasive stones and other surfaces. It has a perfectly smooth surface. Lapping is carried out with abrasive powders or diamond pastes. Approximate dimensions: 200x70x20 mm. Made in Russia.

2400p
Отзывов: 1
Рейтинг:
new

Froe PETROGRAD, model Uglich 300мм

Froe is a special cleaving axe (cleaver) for green woodworking, bodging and spoon making. Long blade and perpendicularly handle make it easy to split wood along the grain. Thick blade back would be good to use with mallet or even log*. Froe axe also good for split logs for fireplace, stove or even for making wood shingles and wooden blanks for spoons.

Edge is lenticular sharpened. Froe "Uglich" by petrograd toolworks is perfect choice for making blanks for spoon making. Froe axe is hand forged and totally made in Saint-Petersburg Russia

8000p
Отзывов: 1
Рейтинг:

The book `Practical course of woodworking art` + Atlas of drawings, M. Netyksa

The fundamental book on the treatment of wood for professionals and amateurs, which was the basic textbook on woodworking, the entire first half of the twentieth century. Moscow 1901 / Reprint edition of St. Petersburg 2016. Format 145x215 mm, hard fabric binding, 680 pages, 755 illustrations. Also available is a set of drawings attached to the 1901 edition. The author is M. A. Netyksa, a member of the Scientific Department of the Society for the Distribution of Technical Knowledge.

Table of contents.
Division I.
Chapter I. The wood, its structure and properties ... The age of the twood ... The color of the wood ... The density of the wood ...
Chapter II Cutting wood into boards ... Machine sawing boards ... Diseases, defects and structural features of wood ...
Chapter III Various wood species ...
Chapter IV Chemical painting of wood ... Coloring methods and preparation of dye solutions ...
Division II.
Chapter I. The workbench and some adaptations to it ...
Saws and sawing ...
Chapter II Measuring, marking and testing instruments ... Compasses ...
Chapter III Cleaving, curing, cutting and planing ... Planes and planing ...
Chapter IV Rasps and filings ...
Chapter V. Drills and drilling ... Devices and devices for turning various drills ...
Chapter VI. Chisels ... Slotters ...
Chapter VII Various tools and accessories ... Devices for gluing ...
Chapter VIII. Sharpening  ...
Chapter IX The device and acquisition of a workshop ...
Division III. Different types of wooden joints ...
Division IV. Wooden surface finish ...
Division V. Furniture joinery ...
Division VI. Model business ...
Division VII. Machine building ...

2200p
Отзывов: 1
Рейтинг:

Sharpening stone PETROGRAD, 200*70*20mm, 4000 grit

Water stones. Grain size: 150, 360, 500, 1000, 1500, 2000 and 4000 grit. Size 200*70*20mm. Abrasive grain - silicon carbide. Bundle - ceramics. Hardness I ensures minimal wear of the stone during operation. When sharpening does not overheat the steel. Does not require the use of oil. Soak in water for 2-10 minutes before use. Designed for sharpening steels and hard alloys. Made in Russia.

 

3440p
Отзывов: 1
Рейтинг: