PETROGRAD axe, model Roslavl 7, Laminate, handle n11, authorship of A.S.Savin

Carving knives with a sharp tip are designed for detailing and working in hard to reach places. Blade length 45mm or 60mm, rounded butt. A comfortable oval redwood handle is saturated with oil and covered with shellac. The length of the handle - 115mm. Excellent knife for both beginners and professionals. The 2.5 mm thick blade is made of high carbon steel hardened to a 59-61 HRc. All the cutters are sharpened and ready to go. Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Wooden mallet, round shape. Solid wood mallets made by woodturning. Mallet weight 300 gramm. Mallets made of beech wood and covered with tung oil. Round mallets used for working with mortise chisels and woodcarving chisels. It used when cutting joints and when carving large elements or sculptures (work from under the mallet).

Production of Petrograd toolworks. Made in Saint Petersburg Russia.

Forged corner carpenter chisel PETROGRAD 25*25 mm with a wooden handle are designed for hard work with wood. The blade is forged manually from steel ШХ15 (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6) and hardened to a hardness of 58-61 HRC. With the help of machining specified exact geometry. Designed for processing and cleaning the corners of deep grooves. The handles are made of ash and crimped with two stainless rings - one to prevent splitting wood near the handle, the second to harden the back of the bar when working with a mallet or hammer. A leather pad between the chisel and the grip allows you to dampen the blows. Available in 25 mm wide. Blade length 300 mm, total length 550 mm. The guarantee of 100% quality is a small hole on the back of the chisel - a trace from the diamond cone of the device for determining the hardness. This test passes every chisel.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Bent Gouge Rubankov, N7, 30mm (1.8 inches)

Carving chisel "Rubankov" Bent Gouge N7, 30mm ( 1.8 inches ). Perfectly suits for volume carving and deep hollow carving. The width of the cutting edge is 30mm ( 1.8inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.

Gouge is sharpened, honed and fully ready to work out of the box.
This model is for hand cutting and can be used with a mallet.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )

Checkering layout guide is necessary for confident marking of lines under the notch, for drawing notches parallel to the upper line of the forearm, for accurate drawing and repeatability of the notch pattern on both sides of the bed, for marking the edge of the guide lines with the original pattern.

Checkering layout guide is regulated along the entire length of the installation of both the upper and lower notch lines, and the length of the fixed handle is sufficient to reach the other side even through the widest trunk.

Working length of a rod is 77 mm.
Knife projection from 6.5 mm to 48.5 mm

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Резец C-1, имеет 1 пирамидальный зуб. Угол вершины 90 и 60 градусов. Резец продается в сборе, имеют удобную рукоять из бука и шток с установленной на нем рабочей частью. Все резцы изготовлены из стали, прошли процесс закалки и обработки, для продолжительной и надежной работы.
Имеет V-образную форму с зубцами по обе стороны. Резец С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами.
Деревянная рукоятка хорошо сбалансирована и удобно лежит в руке.
На фотографии детально показаны зубцы. Обратите внимание на высокую рельефность, обеспечивающую быструю и ровную нарезку. Зубцы обеспечивает хорошее удаление всех твердых пород древесины.
Резцу все равно, что вырезать глубокие или мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. Ровной получается каждый элемент.

Ширина рабочей части 5 мм, длина рабочей части 11 мм, угол вершины 90 и 60 градусов.

Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.

Сделано в России

Checkering tools from L-series have two sides: left side with teeth, right side - smooth, used as a guide. Between the tool tips, the gap is equal to the pitch. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. At the same time between the previous line and the new remains empty space - the line width in the usual row. Thus, it is possible to alternate sections with a notch and neat smooth lines of the same width. Such a notch principle is often called "French" or "Scottish."

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.

Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.

Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.