Share / Save Link:
Petrograd Brass Square 85mm with base, two-side marking
Description
Square PETROGRAD, ground. Double-sided, 85 * 50mm in size. The square is one of the most used measuring tools in joinery. Ruler width 15 mm. Metric markings in 1 mm increments on the outside and inside, on both sides. The error of the square is 0.05mm per 100mm. It is used not only for checking 90 degree angles, but also for setting up tools, saws and other tools. Also handy for marking with a pencil or a knife. Material - brass. Engraved etched markings for easy reading.
Made in Russia
Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
Petrograd Bevel Setter, 200mm*55mm, for sliding bevels
Petrograd Bevel Setter, 200mm*55mm, for sliding bevels. This is an ingenious tool for setting angles when lining up and for marking or measuring workpieces. Pieces can be positioned freely in line with the etched markings. Special dovetail and polygon markings are on the back, as well as a millimetre scale.
Wooden bench plane PETROGRAD, 50mm/230mm
Traditional wooden plane. The shoe is made of maple with brass insert for reliable fixation of the blade, the sole is made of hornbeam. The wedge is also made of maple, easy to install and remove. The installation angle of the blade is 50 °.
The plane blade is made of steel 9ХС (DIN - 150Cr14). Hardened to 59-61 HRC. Dimensions: total length 175 mm, width 60 mm, thickness minimum 3.5 mm, thickness maximum 5 mm.
All blades are wedge-shaped with a wedge angle of 0.5 degrees, which favorably distinguishes them from others, and are ideally suited for wooden planes with wedge fixation.
Blades have two sides - one is hard, the other is soft (production feature)
Absolutely every blade is tested with a hardness tester.
The solid side has 2 points from the diamond cone - the test, and the control test.
The manufacturer reserves the right to change the thickness and appearance of the knife without degrading the working qualities of the tool.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Popular goods
Carving chisel, PETROGRAD, 6mm
Carving chisels.
The model range includes straight chisels with a width of 2mm, 4mm, 6mm, 8mm, 10mm, 12mm, 14mm. Chisels are made of steel 65 G (Germany 66Mn4, Ck67, USA 1066) and have beech handles coated with tung oil. Blade length - 35 mm, total length - 180 mm, sharpening angle - 30 degrees, blade thickness - 2 mm.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia
Adze PETROGRAD, half round N2
Adze N2 created on the basis of a study of ancient tools, made in the northern regions of Russia and now stored in our Museum of Ancient Instruments.
Forged tempered to hardness - 58-60HRc. The adze is made of spring steel 65 g (Germany 66Mn4, Ck67, USA 1066). The width of the blade is 70 mm. Total length - 500 mm. Weight - 1.3 kg.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia
Marking knife PETROGRAD, model N2, arrow form
Marking knives PETROGRAD have a unilateral right or left sharpening and bevel at an angle of 30 and 45 degrees. The blade of the knife is made of high carbon steel and hardened to 59HRC, it passes through the entire handle - this allows you to use it not only as a marking knife, but also as a power knife jamb. Blade thickness - 1.7mm, width - 19mm. The lining is made of beech wood, covered with tung oil and fastened with brass rivets. The length of the knife is 165mm, the blade is 70mm.
Butcher axe, model Rzhev, half round
Classy axe for cutting meat. Forged tempered blade has a hardness of 58-60HRc. The axe is made of 9XC (DIN - 150Cr14) alloyed tool steel. Half round cutting edge. Sharpening 30 degrees. The axe handle is made of maple wood, covered with tung oil and has a curved finish.Fixed to the cross with two wooden wedges. Comes with a leather case with a fixation on the buttons.
The width of the forging is 220 mm, the ax handle is 370 mm long, the total length is 450 mm, and the weight is 2000 g.
Totally hand made at PETROGRAD factory of joinery and carpentry tools.
Made in Russia.
Checkering tool complete C-1, 90°
Checkering tool C-1 has 1 pyramidal tooth. Angle top 90 degrees. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Checkering tool C-1 is designed for applying the original layout of the picture, as well as for deepening the grooves after their application, with other cutters.
The wooden handle is made of beech, well balanced and lies comfortably in your hand.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter doesnt look like cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Equal each element is obtained.
The width of the working part is 5 mm, the length of the working part is 11 mm, the apex angle 90 degrees.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N2-22, 90°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete S-1, 90°
Checkering tool S-1 has 1 pyramidal tooth. Angle of the top is 90 degrees. The cutter has a convenient beech handle and a rod with a sharp bend perpendicular to the cutting axis and the working part installed on it. All the cutters are made of steel, undergone the process of hardening and processing, for long and reliable work.
It is V-shaped with teeth on both sides. Designed to handle corners and bends, as well as hard-to-reach places.
Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
The cutter has not matter what cutting - deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Every element is smooth and beautiful.
The width of the working part is 5 mm, the length of the working part is 5 mm, the apex angle is 90 °
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Carving chisel, PETROGRAD, half round, 10mm
Half round carving chisel PETROGRAD designed for threading medium-sized parts and for detailing small forms. Made of 65G (Germany 66Mn4, Ck67, USA 1066) forged steel. The beech handle is barrel-shaped, which makes it possible to securely and conveniently hold the chisel without tiring the wrist. Coating oil wax. The length of the handle - 140 mm, the total length - 175 mm, width - 10 mm.
Designed for both amateurs and professionals engaged in medium-sized products.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Bit for checkering tool C-1, 90°
Насадка на резец для чекеринга C-1, 90° (одна РК) имеет 1 пирамидальный зуб. Уголы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резецы С-1 предназначен для нанесения оригинального макета рисунка, а также для углубления канавок после их нанесения, другими резцами. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России
Bit for checkering tool S-1, 90°
Насадка на резец для чекеринга S-1, 90° (одна РК) имеет 1 пирамидальный зуб. Углы вершин 90 и 60 градусов. Все резцы изготовлены из стали, прошли процесс закалки и обработки. Имеют V-образную форму. Резцы S-предназначен для обработки углов и изгибов, а также труднодоступных мест. Высокая рельефность обеспечивает быструю и ровную нарезку на твердых породах древесины. Резцы могут резать, как глубокие так и мелкие пазы, прямые или закругленные углы, параллельные линии или перекрестную штриховку, по направлению волокна или поперек. Не нужно заново делать проход, чтобы обработать неровные участки. При определенных навыках ровной получается каждая канавка.
Производство - фабрика столярных и плотницких инструментов ПЕТРОГРАДЪ.
Сделано в России