Share / Save Link:
Description
Slick chisel "Onega" by Petrograd toolworks is one of best choices for Timber Framing joinery. Slick Onega is a fine combination of weight, balance and splendid sharpening and flatness. All that will give you an extraodinary feeling wile working with our timber frame slicks.
- blade offset of handle
- blade width - 70 mm
- blade lenght - 300 mm
- blade made of ШХ15 steel (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6)
- hardened to 58-61HRc
The blade is hand forged and has off-set from the handle. This allows extra clearance when working on deep mortices or taking long paring cuts.
Made of ШХ15 steel our "Onega" slicks offer a perfect combination of hardness and toughness together with a razor sharp cutting edge.
The back side of blade (near handle) is rounded off to eliminate sharp corners giving extra comfort and security.
- rased up handle
- handle lenght 500 mm
- handle made of ash wood
- leather pad
All carpentr's slicks Onega comes with leather holster for edge protection. Every Blade is tested for hardness, sharp and ready to work.
This is a complete tool for timber frame joinery and othe heavy duty work.
- full lenght - 820 mm
- weight - 1.7 Kg
| Weight: | 1.7 kg |
|---|---|
| Type: | Timber Framing Slick |
| Steel: | ШХ15 |
| Handle material: | Ash* |
| Edge: | Straight |
| Edge width: | 70mm |
| Blade lenght: | 300 mm |
| Total lenght: | 820 mm |
*material of handles may changes from batch to batch.
Share / Save Link:
Videos
Specs
Reviews
Instructions ()
Publications
Recommended products
Carpenter Slick Chisel, PETROGRAD, model Onega, 60mm
Carpenters Slick "Onega" by Petrograd toolworks is one of best choices for Timber Framing joinery. Slick Onega is a fine combination of weight, balance and splendid sharpening and flatness. All that will give you an extraodinary feeling wile working with our carpentry slicks.
- blade offset of handle
- blade width - 60 mm
- blade lenght - 300 mm
- blade made of ШХ15 steel (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6)
- hardened to 58-61HRc
The blade is hand forged and has off-set from the handle. This allows extra clearance when working on deep mortices or taking long paring cuts.
Made of ШХ15 steel our "Onega" slicks offer a perfect combination of hardness and toughness together with a razor sharp cutting edge.
The back side of blade (near handle) is rounded off to eliminate sharp corners giving extra comfort and security.
- rased up handle
- handle lenght 500 mm
- handle made of ash wood
- leather pad
All carpentr's slicks Onega comes with leather holster for edge protection. Every Blade is tested for hardness, sharp and ready to work.
This is a complete tool for timber frame joinery and othe heavy duty work.
- full lenght - 820 mm
- weight - 1.4 Kg
Carpenter Slick Chisel, PETROGRAD, model Onega, 80mm
Carpenters Slick "Onega" by Petrograd toolworks is one of best choices for Timber Framing joinery. Slick Onega is a fine combination of weight, balance and splendid sharpening and flatness. All that will give you an extraodinary feeling wile working with our carpentry slicks.
- blade offset of handle
- blade width - 80 mm
- blade lenght - 300 mm
- blade made of ШХ15 steel (USA 52100, G52986, J19965; Germany 1.3505, 100Cr6, 102Cr6)
- hardened to 58-61HRc
The blade is hand forged and has off-set from the handle. This allows extra clearance when working on deep mortices or taking long paring cuts.
Made of ШХ15 steel our "Onega" slicks offer a perfect combination of hardness and toughness together with a razor sharp cutting edge.
The back side of blade (near handle) is rounded off to eliminate sharp corners giving extra comfort and security.
- rased up handle
- handle lenght 500 mm
- handle made of ash wood
- leather pad
All carpentr's slicks Onega comes with leather holster for edge protection. Every Blade is tested for hardness, sharp and ready to work.
This is a complete tool for timber frame joinery and othe heavy duty work.
- full lenght - 820 mm
- weight - 2.0 Kg
Bench Chisel, PETROGRAD, model Istra short, 50mm
Forged carpentry short chisels Istra with a straight cutting edge and a wooden handle, has designed for hard work. The basis for the manufacture of chisels Istra was taken the form of old Russian chisels from the old tools museum Rubankov, and also takes into account long-term experience in the development of professional carpentry and carpentry tools of other toolworks.
The blade has forged manually from steel ШХ15 (USA analog is 52100, G52986, J19965; Germany analog of 1.3505, 100Cr6, 102Cr6) and hardened to 58-61 HRC. Carpentry chisels are intended for timber framing for processing deep grooves in logs and timber as an indispensable tool for the construction of frame structures in the style of timber frame, post-and-beam half-timbered, fachwerkhaus, Log house.
- Chisel blade fastened to the handle with a conical socket.
- The thickness of the blade at the neck is 11 mm, the thickness in the area of the descent is 7 mm.
- The handles are made of ash and crimped with a stainless ring to harden the butt when working with a mallet or hammer.
- Available in widths of 19 mm, 25 mm, 38 mm, 40 mm and 50 mm ( see full catalogue).
- Blade length 300 mm, full length 410 mm.
- The wedge-shaped blade prevents jamming in the wood.
Carpentry chisels Istra are totally hand made at PETROGRAD toolworks of joinery and carpentry tools. Made in Saint-Petersburg Russia.
Popular goods
Checkering tool complete B-1
Checkering too B-1, is a 2 conical cutter with a working angle of 90 degrees, separated by a wide groove with teeth. A tool for making the roller around the notch. Pay attention to the high relief, providing fast and smooth cutting. The tines provide good removal of all hardwoods.
A cutter is just the same as cutting deep or shallow grooves, right or rounded corners, parallel lines or cross-hatching, in the direction of the fiber or across. No need to re-do the pass to treat uneven areas. Smoothly each groove is obtained.
Maximum roller height 1 mm, width 2.5 mm
Made in Russia.
Checkering tool complete N2-18, 60°
Checkering tool No2. Both sides with teeth. Used for the application of grooves and their deepening after application. One blade runs along the guideline, while the other marks the next groove. When moving to the next groove, the tool deepens it and again applies the next groove. Cutter 2 It is a combination of tools for expanding and deepening grooves. Beech handle. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N3-18, 60°
Checkering tools from series N3, have two sides: the right side is smooth, used as a guide, the left - with teeth. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The right blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The left blade has teeth and cuts a new groove during the process of notching from right to left. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Checkering tool complete N4-18, 60°
Checkering tools from series N4 have two sides: the right side with teeth, the left - smooth, is used as a guide. All the cutters are made of steel, underwent a process of hardening and processing, for long and reliable work. The left blade is devoid of teeth, has a sharp and smooth shape, and exactly follows along the guide line. The right blade has teeth and cuts a new groove during the process of notching from left to right. Thus, it is possible to apply a notch, using the previous groove, as a guide. Beech handle.
Totally hand made at PETROGRAD factory of joinery and carpentry tools. Made in Russia.
Leather Knife PETROGRAD, type 1, single stright bevel
Straight and flat leather Knife type 1 with a single bevel (up or right). This model has one flat side and one bevel side. It's simple knife for paring and skiving.
- for straight cuts
- for skiving
- for paring
Flat Leather knife type 1 by Petrograd toolworks comes with a leather sheath. Edge is perfectly sharpened and ready to work out of the box.
This type of knives is used in handicraft, leather work, and shoemaking.
- blade made of tool alloy steel 9ХФ
- blade thickness - 1.7 mm
- edge lenght - 40 mm
- blade lenght - 70mm
- handle made of wood *
- oil covered **
Straight Gouge Rubankov, N3, 6mm
Straight Gouge Rubankov, N3, 6mm
Straight Gouge Rubankov, N3, 6mm (0.43 inches)
Carving chisel "Rubankov" Straight Gouge N3, 6mm (0.43 inches). This is universal chisel that perfectly suits for carving hard and soft wood. The width of the cutting edge is 6mm ( 0.43 inches ). The total lenght of the gouge is 280mm (11.02inches ), blade lenght is 145mm ( 5.71inches ), the lenght of the handle is 135mm (5.31inches ). Made of alloy steel, hand forged and hardened to 59-61HRc. The comfortable and ergonomic oval handle is made of cherrywood ( may change) and coated with oil.
Gouge is sharpened, honed and fully ready to work out of the box.
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )
Straight Gouge Rubankov, N2, 14mm, fishtail
RUBANKOV chisels are forged from low-alloy high-carbon steel. Hardened to a hardness of 59-61 HRc.
The faceted handle is made of precious wood and covered with oil. The impact side is rounded so as not to crush calluses on the palms. The brass ring has an exquisite look and the effect of the handle from cracking when working with a mallet. The internal profile of the chisel is polished, the detected edge is sharpened and ready for work.
These models are percussion, they can be paired with a mallet.
The declared geometric dimensions vary in handling, as the tool is made and hoarded by hand.
The length of the metal sheet is 145 mm. Overall length with handle 280mm.
Web width - 14mm.
Made at the PETROGRAD joinery and carpentry tools factory.
Production Russia.
Straight Carving Chisel Rubankov, N1, 10mm
Straight carving gouge N1 has 10mm wide blade(0.39 inches) and slight profile for better carving abilities. It is universal wood carving chisel that perfectly suits for carving hard or soft wood. Best choice for relief wood carving.
- cutting edge width - 10mm (0.39 inches)
- blade lenght is 145mm (5.71inches)
- Made of alloy steel
- hand forged
- hardened to 59-61HRc
Produced by PETROGRAD toolworks. ( Saint-Petersburg Russia )
Carving set PETROGRAD n19, 6 tools, chisel handles
Набор мини стамесок для резьбы по дереву, ПЕТРОГРАДЪ, N19, 6 предметов. Авторский набор мини-стамесок для миниатюрной резьбы по дереву. Эти прекрасные инструменты подойдут для моделистов, любителей миниатюрной резьбы и для максимальной деталировки резьбы. Набор включает три плоские прямые стамески, две косые стамески и одну полукруглую стамеску. Производство Россия.
Petrograd Bushcraft Straight Gouge, n7, 30mm
Прямая стамеска для вырезания ложки, профиль Н7, ширина 30 мм. Эта стамеска была специально разработана с оглядкой на нужды ложкарей, ее профиль и общие габариты, даже внешний вид, подобраны исходя из эргономики изготовления деревянной ложки. Прямые стамески подходит для множества задач от создания фигурных форм до подбора фона Стамеска подойдет и для классической резьбы при съеме материала. Производство фабрика Петроградъ (Россия)