Верстак 2000*600мм, с лотком, ПТ - коробка York HV511, БТ - York 516
Description
Габариты верстачной доски - 2000х600 мм, толщина щита - 40мм. Обвязочная доска высотой 120 мм с соединениями на ласточкин хвост. На верстаке установлены передние Г-образные тиски (фронтальные) тиски и задние (боковые) коробчатые тиски. Передние тиски сделаны на основе металической винтовой пары York HV511, ширина раскрытия -170 мм. Ширина подвижной губки передних тисков - 250 мм, высота - 120 мм, толщина - 60 мм. Задние тиски сделаны на основе металической винтовой пары York HV516 с деревянной направляющей. Ширина прижимной части задних тисков - 410 мм, ширина раскрытия - 275 мм. Губки тисков и опоры подверстачья украшены легким узором. Край верстачной доски в районе задних тисков лежит вне плоскости ножек подверстачья, что позволяет зажимать длинные брусья и рейки в вертикальном положении. Для установки упоров в столешнице и в задних тисках просверлен ряд отверстий. В обвязочной доске с рабочей стороны также просверлены 4 горизонтальных отверстия под упоры. Диаметр отверстий - 19 мм. Для усиления подверстачья между ножками установлена дополнительная верхняя пара продольных перекладин. Материал верстачной доски - буковый щит, подверстачье и рукояти - массив бука. Столешница и подверстачье покрыты тунговым маслом Borma . Верстак необходимо устанавливать на ровную горизонтальную поверхность во избежание коробления и деформации верстачной доски. Высота верстака - 850 мм. Масса верстака - примерно 85 кг.
Габариты верстачной доски с тисками - 2182x986 мм. В конструкцию верстака могут вноситься небольшие изменения, не влияющие на его качество.Верстачные упоры в комплекте 4 шт. На все верстаки производства компании Рубанков можно установить дополнительные вертикальные тиски и опорную доску. К заказу доступны 2 варианта комплектации: верстачная доска с подверстачьем и отдельно верстачная доска.
Производство - мастерская Рубанков (Россия).
Share / Save Link:
Specs
Reviews
Instructions ()
Publications
Recommended products
Magazine Master&Workshop 2020 № 2 (9)
Журнал Мастер и мастерская 2020 2 (9)
Moxon vise, 550mm
Joinery vise, model Moxon, capture width - 550mm. (Dovetail vise, Moxon vise.)
A special version of the vise with two screws for convenient work with the edges and ends of the panels.
Maximum width of the workpiece to be clamped (distance between screws) 550mm.
Maximum workpiece thickness (screw travel) - 30mm
The vise was designed by Sergey Aleksandrovich Klein based on the early work of Anry Ruobo and Joseph Moxon.
We did not strive to make an exact copy of the vise, we set ourselves the task of making a functional and affordable tool for comfort when working with a dovetail joint. This vise does not replace the classic workbench, but is a device that expands the arsenal of any craftsman.
We reserve the right to make minor design changes to improve vise performance.
Oil PETROGRAD for workbenches and tool handles, 0.5l
Finishing oil PETROGRAD for workbenches and tool handles, 0.5l. Primer, used to apply the first coat before finishing. Recommended for use on hard or absorbent wood. Recommended for workbenches, tables, handles, woodworking tools and other woodworking parts. For indoor use only. It quickly and deeply penetrates the material and also quickly polymerizes.
Composition:
Tung oil, linseed oil, modified oils (linseed, tung, safflower, walnut), ricin oil, carnauba wax, micronized wax.
Mode of application:
Apply oil evenly to the prepared surface free of dirt and grease using a brush or lint-free cloth. After 10 minutes, wipe off the remaining oil from the surface with a dry, lint-free cloth. After 8 hours (depending on layer thickness and ambient temperature) apply a second coat. Ensure good ventilation of the room, both during application and at the end of work.
Note:
Certain oily, exotic or brightly colored woods and excessive amounts can prevent the oil from drying or greatly slow down the drying process. In this case, good ventilation is needed to speed it up.
- Do not use nitrile gloves for work.
- Safe for hands
- Always wear protective goggles when working.
Storage:
In a sealed container. It should be kept away from sources of fire and sparks.
Production - Russia.
Hold Down Clamp, PETROGRAD, type 1
Clamp for quick fixing of workpieces. The clamp is hand forged. To use it, insert it into one of the holes for the stops in the workbench tabletop and press down the workpiece. Depth and height of workpiece clamping 120 mm. The diameter of the clamping rod is 16-17 mm. The size of the clamp is 290 x 200 mm. Material - steel.
Production - factory of joinery and carpentry tools PETROGRAD.
Made in Russia